Advertisement
1. and 2. above, then press [VOL ], then [CABLE] in step 3.
To control volume / mute through your TV or Audio device
in the remote's video mode...
1. Press [DEVICE], then [MUTE] together - hold both down
until the lighted mode buttons start blinking in sequence.
2. Press [VIDEO] to select the video mode. The VIDEO
button will illuminate.
3. Press [VOL ], then [TV] for TV volume. Or [VOL ] then
[AUDIO] for audio volume. The [VIDEO] button will blink 2
times and go out.
13. Your Remote's SmartKeys™
Your remote is equipped with three (3) SmartKeys™ ([CBL],
[TV], [BYPASS]) that operate in its cable mode.
Each SmartKey™ can be programmed so whenever it's
pressed, it can transmit up to 8 individual button presses in
sequence.
Programming and using the [CABLE] SmartKey™
The [CABLE] button normally turns on / off your cable
converter.
You can program the [CABLE] SmartKey™ to turn on your
converter, TV, VIDEO and AUDIO devices with one button
press.
1. Press [DEVICE], then [CABLE] to select the Cable mode
of your remote.
2. Press [CABLE], then [SEL] together – hold both down
together until the [CABLE] button illuminates.
3. In this order, press [TV], [VIDEO], [AUDIO]. The
[CABLE]
button will blink and remain illuminated.
4. Press [CH ] to lock in this setting. The [CABLE] button
will blink 2 times and go out.
To return the [CABLE] button to its normal default setting,
repeat steps 1 and 2 above, then press [CH ].
Programming and using the [TV] SmartKey™
The [TV] button normally turns on / off your TV.
You can program the [TV] SmartKey™ so whenever it is
pressed, it will turn on your TV, then tune your TV to its correct
output channel (typically 3) with one button press.
1. Press [DEVICE], then [CABLE] to select the CABLE mode
of your remote.
2. Press [TV], then [SEL] together – hold both down together
until the [TV] button illuminates.
3. In this order, press [0], [3]. The [TV] button will blink and
remain illuminated.
4. Press [CH ] to lock in this setting. The [TV] button will
blink 2 times and go out.
To return the [TV] button to its normal default setting, repeat
steps 1 and 2 above, then press [CH ].
Programming and using the [BYPASS] SmartKey™
The [BYPASS] button (CABLE mode) normally puts your
converter in a BYPASS mode. While the converter is in its
BYPASS mode, you can record one program on your VCR
while watching a different program through your TV.
exiting your converter's BYPASS mode, your TV must be re-
tuned to its correct output channel (typically 3) for proper cable
reception.
You can program the [BYPASS] SmartKey™ to automatically
tune your TV to its correct output channel.
1. Press [DEVICE], then [CABLE] to select the Cable mode
of your remote.
2. Press [BYPASS], then [SEL] together – hold both down
together until the [CABLE] button illuminates.
3. In this order, press [DEVICE], [TV], [0], [3]. The [CABLE]
button will blink and remain illuminated.
4. Press [CH ] to store the setting. The [CABLE] button will
blink 2 times and go out.
To return the BYPASS SmartKey™ to its normal default
setting, repeat steps 1 and 2 above, then press [CH ].
Remember: When using any SmartKey™ to transmit a series
of functions, be sure to keep your remote aimed at the devices
to ensure all functions are received in their entirety.
nd
14.
Programming a 2
TV, VCR, DVD
Instead of programming an audio device, you can program
nd
nd
your remote to operate a 2
TV, 2
VCR, or 2
Here's an example of how you would program a second TV to
your remote's [AUDIO] button...
1. Turn on your 2
2. Press [DEVICE], then [MUTE] together - hold both buttons
down until the lighted mode buttons start blinking in
sequence.
3. Press [AUDIO], then [TV]. The [AUDIO] and [TV] buttons
will start blinking.
4
a. Press and hold [CH ] until your 2
soon as your 2
OR
b. From the TV Setup Code list, locate and enter the 3-
digit codes until your 2
5. Press [MUTE].
[AUDIO] to lock in the code. The [AUDIO] button will blink
2 times and go out.
When
nd
If your 2
TV doesn't turn back on, repeat steps 4 and 5
above until you can turn your 2
! NOTE when using the Point and Press™ Programming
method (step 4a.). If you find a code that turns your 2
but not back on, you may have gone past the correct matching
code. Try pressing [CH ] one step at a time until find a code
that turns your 2
If you want to program a 2
example, you would press [AUDIO], then [VIDEO] in step 3.,
then steps 4. and 5. referring to the Video Setup Code list.
15.
Code Number Readback
To identify a 3-digit device code stored under the Point and
Press™ method, follow these steps:
1. Press [DEVICE], then [MUTE] - hold both down until the
illuminated mode buttons start blinking in sequence.
2. Press [CABLE] to identify your cable converter code. Or
[TV], [VIDEO], [AUDIO] to identify these codes.
selected mode button will be illuminated.
3. Press [INFO].
code numbers, with a 1 second interval between each digit
of the code.
nd
Example: For code "035", the remote will blink 10 times, then
DVD player.
3 times, then 5 times.
nd
TV.
nd
TV turns off. As
nd
TV turns off, release [CH ]!.
nd
TV turns off.
nd
If your
2
TV turns back on, press
nd
TV off and on.
nd
TV off
nd
TV back on.
nd
VCR or DVD player in the above
The illuminated button "blink back" the
The
Advertisement
