Cobra 15 BAND XRS 9670 Operating Instructions Manual page 7

EasySet Programming Menu
Your Detector
This EasySet Programming menu lists all of the modes and settings you can
choose from after you have entered Program mode as described on page 7.
Mode Tone Visual Setting
Set Two beeps City X
IntelliShield
City mode
One beep City X
default*
beep Off
One beep City X+K
IntelliMute Two beeps IntelliMute On
mode
One beep IntelliMute Off
Set
One beep Set IntelliMute
IntelliMute
(see page 14
RPMs
to set activation
point)
IntelliMute Two beeps IntelliMute Pro
Pro mode
On
One beep IntelliMute Pro
Off
AutoMute Two beeps AutoMute On
mode
One beep AutoMute Off
Set One beep Set Compass
compass
Pop Detect Two beeps Pop Detect On
mode
One beep Pop Detect Off
English
8
Result
A single beep sounds when the
signal is first detected.
Audio for all X band alerts are blocked
until signal strength reaches Level 3.
Combines the City X mode with
prevention of K band audio alerts
until signal strength reaches Level 2.
All alerts (except for strobe signals
from emergency vehicles) are
automatically muted below the
engine rev point you set.
Normal operation.
Allows you to set the engine
rev point while using IntelliMute.
Note: Only shown if IntelliMute is Off.
All radar, VG-2 and Spectre detection is
turned Off below the engine rev set point.
Normal operation.
The audio volume of all alerts will be
automatically muted after four seconds for
as long as the signal is detected.
All alerts will sound at full volume
for as long as the signal is detected.
Allows you to calibrate the compass.
(see page 17 to calibrate compass)
Unit will detect Pop signals.
Unit will not detect Pop signals.
EasySet Programming Menu
Your Detector
Mode Tone Visual Setting
VG-2 Detect Two beeps VG-2 Detect On
mode
One beep VG-2 Detect Off
VG-2 Audio Two beeps VG-2 Audio On
mode (not
shown if VG-2
One beep VG-2 Audio Off
detect is Off)
Spectre Two beeps Spectre
Detect mode Detect On
One beep Spectre
Detect Off
Spectre Two beeps Spectre Audio
Audio mode On
(not shown
One beep Spectre Audio
if Spectre
Off
detect is Off)
SmartPower Two beeps SmartPower On
mode
One beep SmartPower Off
X Band Two beeps X Band On
Detect mode
One beep X Band Off
K or Ku Band Two beeps K or Ku Band On Unit will detect K or Ku Band signals.
Detect mode
One beep K or Ku Band Off Unit will not detect K or Ku Band signals.
Set display Two beeps Display Dim
Dim mode
One beep Display Dimmer More dimmed for dusk or night driving.
default*
One beep Display Dark
Restore factory One beep Restore Factory
settings Settings
Exit program One beep EXIT PROGRAM Allows you to exit Program mode.
* The settings for these user modes can also be changed
with the one button method. See description of each
user mode (pages 10 and 24) for details.
Result
Unit will detect VG-2 signals.
Unit will not detect VG-2 signals.
With VG-2 Detect On, the unit will give
audible alerts for VG-2 signals.
With VG-2 Detect Off, the unit will give
only visual alerts for VG-2 signals.
Unit will detect Spectre I & IV+ signals.
Unit will not detect Spectre I & IV+
signals.
With Spectre Audio On, unit will give
audible alerts for Spectre signals.
With Spectre Audio Off, unit will give only
visual alerts for Spectre signals.
SmartPower is On.
SmartPower is Off.
Unit will detect X Band signals.
Unit will not detect X Band signals.
Partially dimmed for dusk or night driving.
Display is Off.
Resets user modes and settings to
factory default.
Nothing Comes Close to a Cobra 9
®