Paper Thickness - Epson FX-1050 Product Manual

NEW FX - 850/1050 DOT- MATRIX PRINTER
Paper width:
Paper Sheet
Single
Sheet
7.2 to 10.1" (182-257mm) 7.2 to 14.4" (182-366mm)
Continuous
4 to 10" (1101-254 mm)
Envelopes 6.5" or 9.5"
Labels
2.5" or 4.0"
Paper Length:
Single sheet
Printable area:
Single sheet
Number of copies:
Up
thickness must not exceed 0.012" (0.32 mm)
Paper feeding methods: Friction
Posh tractor
Cut sheet feeder (optional)
Pull tractor (optional)
Ribbon
Cartridge ribbon. available in black only:
#875O (FX-85O)
#8755(M) (FX-1050)
Life expectancy of ribbon:
3 million characters (14 dots/character)
MCBF:
For all components excluding print head:
5 million limes
MTBF:
FX 850
FX-1050 6000 power-on hours
print head life:
100 million characters (14 dots/character)
Dimensions and might:
Height:
Width:
Depth:
weight:
voltage:
120 VAC ± 10%
Power consumption:
120 watts maximum
Frequency: 49.5
Insulation resistance:
10M ohms between AC power line and chassis
Dielectric strength (between AC line and chassis):
Can withstand 1.0 kV rms applied for one
minute or 1250 VAC rms applied for one
second.
Temperature:
Operation: 40°F to 95°F (5°C to 35°C)
Storage: -22°F to 140°F (-30°C to 60°C)
NEW FX-850/1050-4
FX-1050
FX-850
4 to 16" (101-406.4 mm)
6.5" or 9.5"
2.5" or 4.0"
7.2
to 14.3 inches (182 to 364 mm)
12 mm (.5") 12 mm (1/2")
sheets including the original. Total
to 4
on
4000 power-on hours
FX-850 FX-1050
5.9' 5.9"
17.9'
24.8"
14.2'
14.2'
20.9 27.5
lbs
to 60.5 Hz
Always return the lever to Position 2 when you go back to printing on
ordinary paper. Continuous printing with the lever set at a position
higher than 2 can shorten the life of the print head.
WARNING: Printing past the edge of envelopes, multi-part
Commands in Numerical Order I
This section lists all the FX commands. with their decimal and
hexadecimal values. The numbers in the columns on the right are the
page numbers in this chapter where a complete description of the
command can be found. If the Epson and IBM emulation mode page
numbers are the same, the command is the same in both modes and is
described only in the Epson mode section.
7
BEL
B e e p c r
B S 8 08 Backspace
9
H T
09 Tab horizontally
LF
10 0A Line feed
VT
11 0B Tab vertically
12
FF
CC Form feed
13
CR 0D Carriage return
14
SO
0E Select double-wide (1 line)
SI 15 OF Select condensed mode
17
18
18
DC2
19
DC3
DC4 20 14 Cancel double-wide (1 line)
CAN 24
DEL 7F Delete character
ESC SO 7: 0E Select doublc-wide (1 line)
lbs
E S C S I 1 5 0F Select condensed mode
ESC EM 25
ESC SP 32 20 Set intercharacter space
21
ESC I 33
ESC # 35
ESC $ 36 24 Set absolute print position
3 7
E S C % 25 Select user-defined set
E S C & 3 8
ESC* 42
2A Select graphics mode
ESC - 45
47
ESC/
ESC 0 48
30 Select l/&inch line spacing
ESC 1 49
ESC 2 50
E S C 2 5 0
ESC 3 51
52
ESC 4
7/20/89
11 Select printer
l2 Cancel condensed mode
12 Cancel condensed/12 cpi prop.
13
Deselect printer
18 Cancel line
19
Cut sheet feeder on/off
Master Select
23 Cancel MSB control
26 Define user-defined characters
2D Turn underlining on/off
2F Select vertical tab channel
31 Select 7/72-inch line spacing
32 Select 1/6-inch line spacing
32 Programmable line spacing
33 Select n/216-inch line spacing
34 Select italic mode
8-12 8-12
8-20 8-20
8-22 8-22
8-15 8-15
8-l8 8-18
8-14 8-14
8-13
8-13
8-27 8-27
8-26 8-26
8-3 8-8
8-26
8-47
8-9
8-27 8-27
8-l3 8-13
8-13
8-27 8-27
8-26 8-26
8-11
8-32
8-24
8-12
8-21
8-36
8-35
8-39
8-31 8-31
8-19
8-16 8-16
8-16 8-16
8-16
8-43
8-17 8-17
8-33
9 - Pin Printers