Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for CDA HCC662
Summary of Contents for CDA HCC662
- Page 1 Manual for Installation, Use and Maintenance Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...
- Page 2 Under no circumstances should any external covers be removed for servicing or maintenance except by suitably qualified personnel. Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model...
- Page 3 Please note: • Ceramic hobs become hot and remain hot during and immediately after use. Do not touch the hob until it has been allowed to cool. • Keep children away from the appliance when in use. • Never put cooking foil or plastic materials on the ceramic surface when the hob is hot. These materials could melt and cause damage to the hob.
-
Page 4: Using Your Hob
Using your hob Fig. 1 Zones: Zone indicators Front left 0.7/2. 1 kW 130/220 mm dual Zone displays Back left 1.2 kW 160 mm Zone selection key Back right 1.8 kW 190 mm Power level + key Power level - key Front right 1.2 kW 160 mm 10. - Page 5 Using your hob To switch the zone on • Touch the power key. • Select the zone required by touching the zone selection key until the required zone flashes a 0 in the zone display. The order for zone selection is clockwise starting at the front right zone. The zone display will flash for approximately ten seconds when the zone will be set at the power level selected or switch off if no power level is set.
-
Page 6: Efficient Use Of Your Hob
Efficient Use of your Hob Before using your hob for the first time, switch the zones on for a FEW SECONDS to burn off any grease left over from the manufacturing process The ceramic glass retains heat, so to make best use of the residual heat, switch off the zone five minutes prior to the end of cooking. -
Page 7: Care And Maintenance
3. Check that the fuse in the spur has not blown. Contact CDA Customer Care A : Customer Care Department, The CDA Group Ltd, Harby Road, Langar, Nottinghamshire, NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu... -
Page 8: Mains Electricity Connection
Mains Electricity Connection Warning! this appliance must be earthed We recommend that the appliance is connected by a qualified electrician, who is a member of the N.I.C.E.I.C. and who will comply with the I.E.E. and local regulations. This appliance is intended to be connected to fixed wiring and is not suitable for connection to a 13a plug or 13a supply. -
Page 9: Fitting The Hob
Fitting the Hob Unpacking the hob: • Take care not to lose or mishandle any parts. Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 190mm away from any adjacent vertical surfaces, e.g. -
Page 10: How To Install The Hob
How to Install the Hob How to install the hob: Overall dimensions of the hob: Width: 580mm Depth: 510mm Worktop cut-out dimensions: Width: 560mm Depth: 490mm 1. Make the required hole in the worktop. Before doing this, you must check the instructions supplied with any cooker hood to ensure that you will have the required clearance. - Page 12 Passionate about style Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...