Page 1: Introduction
TABLE OF CONTENTS SECTION PAGE ............. 3 INTRODUCTION .
Page 3: Table Of Contents
INTRODUCTION CONTENTS Introduction ......4 Vehicle Identification Number ....6 How To Use This Manual .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL This manual has been prepared with the assistance of Consult the table of contents to determine which section service and engineering specialists to acquaint you with contains the information you desire. the operation and maintenance of your vehicle. It is The detailed index, at the rear of this manual, contains a supplemented by a Warranty Information Booklet and complete listing of all subjects.
Page 5: Common Icons
INTRODUCTION 5 Common Icons...
Page 6: Vehicle Identification Number
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures that could result in an accident or bodily injury. It also contains CAUTIONS against procedures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important infor- mation.
Page 7: Vehicle Modifications/Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9: Things To Know Before Starting Your Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Rearming The System ....18 Ignition Key Removal .
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Using The Panic Alarm ....26 Auto Window Down — If Equipped ..36 Programming Additional Transmitters .
Page 11 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Enhanced Seat Belt Reminder System Event Data Recorder (EDR) ....66 (BeltAlert ) ......49 Child Restraint .
Page 12: Things To Know Before Starting Your Vehicle 9
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS IGNITION KEY REMOVAL The dealer that sold you your new vehicle has the key Automatic Transaxle code numbers for your vehicle locks. These numbers can Place the shift lever in PARK. Turn the ignition switch to be used to order duplicate keys from your dealer.
Page 13 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 • For vehicles equipped with the Electronic Vehicle NOTE: • If you try to remove the key before you place the Information Center (EVIC), the power window selector lever in PARK, the key may become trapped switches, radio, hands–free system (if equipped), and temporarily in the ignition switch lock cylinder.
Page 14: Key-In-Ignition Reminder
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE KEY-IN-IGNITION REMINDER WARNING! Opening the driver’s door when the key is in the ignition, sounds a signal to remind you to remove the key. NEVER leave children alone in a vehicle. Leaving children in a vehicle unattended is dangerous for a NOTE: •...
Page 15: Sentry Key
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 turn for three seconds for a bulb check. If the light SENTRY KEY The Sentry Key Immobilizer System prevents unautho- remains after the bulb check, it indicates that there is a rized vehicle operation by disabling the engine. The problem with the electronics.
Page 16: Replacement Keys
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: REPLACEMENT KEYS • The Sentry Key Immobilizer System is not compat- NOTE: Only keys that have been programmed to the ible with some aftermarket remote starting systems. vehicle electronics can be used to start the vehicle. Once Use of these systems may result in vehicle starting a Sentry Key has been programmed to a vehicle, it problems and loss of security protection.
Page 17: Sentry Key Programming
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 4. Insert a blank Sentry Key into the ignition switch. SENTRY KEY PROGRAMMING You can program new keys to the system if you have two Turn the ignition switch to the position within 60 sec- valid sentry keys by performing the following procedure: onds.
Page 18: General Information
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE vehicle. The remaining keys must then be repro- SECURITY ALARM SYSTEM — IF EQUIPPED grammed. All vehicle keys must be taken to the dealer at The Vehicle Security Alarm (VSA) system monitors the the time of service to be reprogrammed.
Page 19: To Arm The System
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 NOTE: TO ARM THE SYSTEM: • During the 16 second arming period, if a door is 1. Remove the keys from the ignition switch and get out opened or the ignition switch is turned ON, the system of the vehicle.
Page 20: To Disarm The System
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TO DISARM THE SYSTEM the system will give you a false alarm. If one of the Either press the UNLOCK button on the remote keyless previously described arming sequences has occurred, the entry transmitter or insert a valid sentry key into the system will arm regardless of whether you are in the ignition lock cylinder and turn the key to the ON/START...
Page 21: Illuminated Entry System - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 NOTE: ILLUMINATED ENTRY SYSTEM — IF EQUIPPED • The front courtesy overhead console and door cour- The courtesy/reading lights will turn on when you use the Remote Keyless Entry (RKE) transmitter or open tesy lights do not turn on if the dimmer control is in either door.
Page 22: Remote Keyless Entry - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY — IF EQUIPPED NOTE: Inserting the key into the ignition switch dis- This system allows you to lock or unlock the doors, open ables all buttons on the transmitter. the trunk, or activate the PANIC alarm from distances a TO UNLOCK THE DOORS maximum of 66 feet (20 meters) using a hand held radio...
Page 23 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 Unlock,” under “Personal Settings (Customer Pro- NOTE: Pressing the LOCK button on the transmitter grammable Features)” under “Electronic Vehicle Infor- while you are inside the vehicle will activate the Security mation Center (EVIC)” in Section 4 of this manual for Alarm.
Page 24: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the Alarm. Opening a door with the Security Alarm activated following procedure: will cause the alarm to sound. Press the UNLOCK button to deactivate the Security Alarm. 1.
Page 25: To Unlatch The Trunk
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 Sound Horn with Lock 2. Release both buttons at the same time. This feature will cause the horn to chirp when the doors 3. Test the feature while outside of the vehicle, by are locked with the transmitter.
Page 26: Using The Express Down Windows Feature
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE USING THE EXPRESS DOWN WINDOWS NOTE: You may need to be close to the vehicle when using the transmitter to turn off the PANIC alarm due to FEATURE This feature allows you to remotely lower both front door the radio frequency noises emitted by the system.
Page 27: General Information
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 GENERAL INFORMATION This device complies with part 15 of FCC rules and with RS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference. 2.
Page 28: Remote Start System - If Equipped
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, military base, and some mobile or CB radios. REMOTE START SYSTEM — IF EQUIPPED Remote start conveniently starts the engine from outside the vehicle by using the Remote Keyless Entry (RKE) key fob while maintaining security.
Page 29: How To Use Remote Start
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Enter Remote Start Mode HOW TO USE REMOTE START All of the following conditions must be met before the Press and release the Remote Start button on engine will remote start: the RKE transmitter twice.
Page 30: Door Locks
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Exit Remote Start Mode Without Driving The To Turn Off The Engine While In Remote Start Vehicle Mode Allow the engine to run for the entire 15 minute cycle. Press and release the remote start button one time. NOTE: To avoid inadvertent shut downs, the system To Exit Remote Start Mode &...
Page 31 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 WARNING! • For personal security, and safety in the event of an accident, lock the vehicle doors as you drive as well as when you park and leave the vehicle. • When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle.
Page 32: Power Door Locks
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CAUTION! An unlocked vehicle is an invitation to thieves. Always remove the key from the ignition and lock all of the doors when leaving the vehicle unattended. POWER DOOR LOCKS A door lock switch is located on the driver and passenger door panel.
Page 33 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Automatic Unlock Doors On Exit (Customer Programmable Features)” under “Elec- The doors will unlock automatically on vehicles with tronic Vehicle Information Center (EVIC)” in Section 4 power door locks if: of this manual for details. •...
Page 34: Child-Protection" Door Lock System (Rear Doors)
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE “CHILD-PROTECTION” DOOR LOCK SYSTEM WARNING! (REAR DOORS) The Rear Door Child-Protection Locks are located inside Avoid trapping anyone in a vehicle in a collision. the rear edge of the door. Insert the tip of the ignition key Remember that the rear doors can only be opened or similar flat-bladed object into the lock and rotate from the outside when the child protection locks are...
Page 35: Power Windows
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 There is a single window control on the passenger’s door POWER WINDOWS trim panel, which operates the passenger door window. POWER WINDOW SWITCHES The window controls will operate when the ignition The control on the driver’s door has up-down switches switch is turned to the ON or ACC position, and when that give you fingertip control of all four power win- the accessory delay feature is active.
Page 36: Auto Window Down - If Equipped
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE AUTO WINDOW DOWN — IF EQUIPPED For vehicles equipped with the Electronic Vehicle Infor- The front window controls on the driver and passenger mation Center (EVIC), the power window switches will door trim panels have an Auto Down feature. These remain active for up to 10 minutes after the ignition switches are labeled AUTO to indicate this capability.
Page 37: Reset Auto Up
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 NOTE: ANTI-PINCH PROTECTION WARNING! • If the window runs into any obstacle during auto- When the window is almost closed, there is no closure, it will reverse direction and then stop. Remove anti-pinch protection.
Page 38: Window Lockout Switch
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOW LOCKOUT SWITCH WIND BUFFETING The window lockout switch on the driver’s door allows Wind buffeting can be described as the perception of you to disable the window control on the other doors. To pressure on the ears or a helicopter type sound in the disable the window controls on the other doors, press the ears.
Page 39: Trunk Release
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 With the key in the lock position or with the key out, the TRUNK RELEASE From inside the car the trunk lid word “deck” will display until the trunk is closed. can be released by depressing the On EVIC equipped vehicles, the words “Trunk Ajar”...
Page 40: Trunk Internal Emergency Release
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE TRUNK INTERNAL EMERGENCY RELEASE NOTE: As a security measure, a Trunk Internal Emer- gency Release lever is built into the trunk latching mechanism. In the event of an individual being locked inside the trunk, the trunk can be simply opened by pulling on the glow-in-the-dark handle attached to the trunk latching mechanism.
Page 41 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 • Advanced multistage driver and new active-vent front • All seat belt systems (except the driver’s) include passenger airbags Automatic Locking Retractors (ALRs), which lock the seat belt webbing into position by extending the belt •...
Page 42: Lap/Shoulder Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and they WARNING! can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown In a collision, you and your passengers can suffer from the vehicle.
Page 43 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 WARNING! WARNING! • Be sure everyone in your vehicle is in a seat and • Wearing your belt in the wrong place could make using a seat belt properly. your injuries in a collision much worse. You might suffer internal injuries, or you could even slide out •...
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the front seat, next to your arm. Grasp the latch plate and pull out the belt.
Page 45 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 WARNING! • A belt that is buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, •...
Page 47 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to •...
Page 48: Adjustable Upper Shoulder Belt Anchorage
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 1. Position the latch plate as close as possible to the anchor point. 2. At about 6 to 12 inches (15 to 30 cm) above the latch plate, grasp and twist the belt webbing 180° to create a fold that begins immediately above the latch plate.
Page 49: Rear Seat Belts
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 NOTE: These devices are not a substitute for proper seat REAR SEAT BELTS Three point belts are nonadjustable for outboard and belt placement by the occupant. The seat belt still must be center rear passengers on sedans.
Page 50: Beltalert Programming
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE BeltAlert will be reactivated if the driver’s seat belt is 3. Within 60 seconds of turning the ignition switch to the unbuckled for more than 10 seconds and the vehicle ON position, unbuckle and then re-buckle the driver’s speed is greater than 5 mph (8 km/h).
Page 51: Automatic Locking Mode
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 How To Disengage The Automatic Locking Mode AUTOMATIC LOCKING MODE In this mode, the shoulder belt is automatically pre- Unbuckle the combination lap/shoulder belt and allow it locked. However, the belt will still retract to remove any to retract completely to disengage the Automatic Locking slack in the shoulder belt.
Page 52: Supplemental Restraint System (Srs) - Airbag
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Seat Belt Extender SUPPLEMENTAL RESTRAINT SYSTEM (SRS) - If a seat belt is too short, even when fully extended and AIRBAG when the adjustable upper shoulder belt anchorage (if This vehicle has airbags for both the driver and front equipped) is in its lowest position, your dealer can passenger as a supplement to the seat belt restraint provide you with a seat belt extender.
Page 53: Airbag System Components
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 This vehicle may also be equipped with window bags to protect the driver, front, and rear passengers sitting next to a window. If the vehicle is equipped with window bags, they are located above the side windows. Their covers are also labeled SRS AIRBAG.
Page 54: Front Seat Airbag Features
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Front Seat— side mounted (Thorax) Airbags — If The first stage inflator is triggered immediately during an Equipped impact that requires airbag deployment. The timing of the second stage determines whether the output force is •...
Page 55 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Front Passenger Airbag Special Features A new active venting front-passenger airbag is designed to reduce the risk of occupants who may be out of position by the use of active vents positioned on each side of the airbag.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Side Airbag Inflatable Curtain (SABIC) — If Equipped Supplemental Side Airbag Inflatable Curtain (SABIC) Airbags offer side-impact protection to front and rear seat outboard occupants in addition to that provided by the body structure.
Page 57 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 WARNING! WARNING! • Do not put anything on or around the airbag • If your vehicle is equipped with left and right covers or attempt to open them manually. You may window bags, do not stack luggage or other cargo damage the airbags and you could be injured up high enough to block the location of the Side because the airbags are not there to protect you.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The seat belts are designed to protect you in many types Children that are not big enough to wear the vehicle seat of collisions. The front airbags deploy in moderate to belt properly (see Section on Child Restraints) should be severe frontal collisions.
Page 59 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 3. The driver and front passenger seats should be WARNING! moved back as far as practical to allow the front airbags room to inflate. • Relying on the airbags alone could lead to more severe injuries in a collision.
Page 60: Airbag Deployment Sensors And Controls
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE AIRBAG DEPLOYMENT SENSORS AND OFF position, in the ACC position, or not in the ignition, the airbags are not on and will not inflate. CONTROLS Occupant Restraint Controller (ORC) The ORC contains a backup power supply system that The Occupant Restraint Controller System (ORC) is will deploy the airbags even if the battery loses power or part of a Federally regulated safety system required for...
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Side Inflatable Curtain and Front Seat Mounted WARNING! Airbags — If equipped The Occupant Restraint Controller System (ORC) de- Ignoring the AIRBAG light in your instrument panel ploys the side inflatable curtain and seat mounted thorax could mean you won’t have the airbags to protect you side airbags during collision with other vehicles and in a collision.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • At no time should any supplemental restraint system (ORC) to properly classify the front passenger and calcu- late the proper airbag deployment. Do not make any (SRS) component or SRS related component or fas- modifications to the front passenger seat components, tener be modified or replaced with any part except assembly, or to the seat cover.
Page 63 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 Enhanced Accident Response System NOTE: A frontal collision that is not severe enough to In the event of an impact that causes airbag deployment, need airbag protection will not activate the system. This with the vehicle stopped, and the vehicle communication does not mean something is wrong with the airbag network intact, and the power intact, the Enhanced...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • As the airbags deflate, you may see some smoke-like WARNING! particles. The particles are a normal by-product of the process that generates the nontoxic gas used for airbag Deployed airbags and seat belt pretensioners cannot inflation.
Page 65 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 Maintaining Your Airbag System NOTE: Perchlorate Material — special handling may apply. See www.dtsc.ca.gov/hazardouswaste/perchlorate WARNING! WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could Do not attempt to modify any part of your advanced be injured if the airbag system is not there to airbag system.
Page 66: Event Data Recorder (Edr)
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag Light EVENT DATA RECORDER (EDR) You will want to have the airbags ready to In the event of an accident, your vehicle is designed to inflate for your protection in a collision. While record up to 5 seconds of specific vehicle data parameters the airbag system is designed to be mainte- (see the following list) in an event data recorder prior to...
Page 67 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 In conjunction with other data gathered during a com- provided to the custodial entity upon request. General plete accident investigation, the electronic data may be data that does not identify particular vehicles or crashes used by DaimlerChrysler Corporation and others to learn may be released for incorporation in aggregate crash more about the possible causes of crashes and associated...
Page 68: Child Restraint
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Transmission gear selection Data Parameters that May Be Recorded: • Diagnostic trouble code(s) and warning light status for • Cruise control status electronically-controlled safety systems, including the • Traction/Stability Control status airbag system •...
Page 69 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 Infants And Small Children WARNING! • Safety experts recommend that children ride In a collision, an unrestrained child, even a tiny baby, rearward-facing in the vehicle until they are at least can become a missile inside the vehicle. The force one year old and weigh at least 20 lbs (9 kg).
Page 70 70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Rearward-facing child seats must NEVER be used in with knees bent over the vehicle’s cushion while the the front seat of a vehicle with a front passenger child’s back is against the seatback, then the child should airbag.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • Carefully follow the instructions that come with the Here are some tips on getting the most out of your child restraints: restraint. If you install the restraint improperly, it may not work when you need it. •...
Page 72 72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE around, and insert the latch plate into the buckle using the vehicle seat belt. The outboard rear seating again. If you still can’t make the child restraint secure, positions have lower anchorages that are capable of try a different seating position.
Page 73 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Rear Seat LATCH Anchors Child restraints systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the top tether anchorage have been available for some time.
Page 74 74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE have tether straps, and you are urged to take advantage Installing the LATCH-Compatible Child Restraint of all of the available attachments provided with your System child restraint in any vehicle. We urge that you carefully follow the directions of the manufacturer when installing your child restraint.
Page 75 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 window. These tether strap anchorages are under a most direct path between the anchor and the child plastic cover with this symbol on it. restraint. Finally, tighten all three straps as you push the child restraint rearward and downward into the seat, Many, but not all restraint systems will be equipped with removing slack in the straps according to the child...
Page 76 76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE the child restraint belt path and then buckle it. This should stow the seat belt out of the reach of an inquisitive child. Remind all children in the vehicle that the seat belts are not toys and should not be played with, and never leave your child unattended in the vehicle.
Page 77 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 route the tether strap under the head restraint and Installing Child Restraints Using the Vehicle Seat between the two posts. If not possible, lower the head belt restraint and pass the tether strap around the outboard The passenger seat belts are equipped with Automatic side of the head restraint.
Page 78 78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE In the rear seat, you may have trouble tightening the over the front of the seat when their back is against the lap/shoulder belt on the child restraint because the seat back, should use the lap/shoulder belt in a rear seat. buckle or latch plate is too close to the belt path opening Make sure that: on the restraint.
Page 79: Engine Break-In Recommendations
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 Pets should be restrained in the rear seat in pet harnesses shown in Section 7 of this manual. NON-DETERGENT or pet carriers that are secured by seat belts. OR STRAIGHT MINERAL OILS MUST NEVER BE USED.
Page 80: Safety Checks You Should Make Inside The Vehicle
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Do not run the engine in a closed garage or in confined Safety Checks You Should Make Inside The areas any longer than needed to move your vehicle in or Vehicle out of the area. Seat Belts If it is necessary to sit in a parked vehicle with the engine Inspect the belt system periodically, checking for cuts,...
Page 81: Periodic Safety Checks You Should Make Outside The Vehicle
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 Defroster Lights Check operation by selecting the defrost mode and place Have someone observe the operation of exterior lights the blower control on high speed. You should be able to while you work the controls. Check turn signal and high feel the air directed against the windshield.
Page 83: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......87 Phone Call Features ....100 Inside Day/Night Mirror —...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training ......122 Headlights; Parking Lights; Instrument Lights ......133 Seats .
Page 85 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 Headlights With Wipers (Available With Auto Garage Door Opener — If Equipped ..146 Headlights Only) ..... 140 Programming HomeLink .
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Venting Sunroof - Express ....154 Cigar Lighter And Ash Receiver — If Equipped ......158 Closing Sunroof - Express .
Page 87: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 87 Annoying headlight glare can be reduced by moving the MIRRORS small control under the mirror to the night position INSIDE DAY/NIGHT MIRROR — IF EQUIPPED (toward rear of vehicle). The mirror should be adjusted Adjust the mirror to center on the view through the rear while set in the day position (toward windshield).
Page 88: Electric Remote-Control Mirrors
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! To avoid damage to the mirror during cleaning, never spray any cleaning solution directly onto the mirror. Apply the solution onto a clean cloth and wipe the mirror clean. ELECTRIC REMOTE-CONTROL MIRRORS Both of the outside mirrors can be adjusted by using the remote controls mounted on the driver’s door panel.
Page 89: Adjusting Side View Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 89 Power Mirror Adjust Switch Mirror Directions After selecting a mirror, move the knob in the same ADJUSTING SIDE VIEW MIRRORS direction you want the mirror to move. When finished, Outside Mirror — Driver’s Side return the knob to the center O (OFF) position to guard Adjust the outside mirror to center on the adjacent lane of against accidentally moving a mirror position.
Page 90: Illuminated Vanity Mirrors - If Equipped
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Outside Mirror — Passenger’s Side ILLUMINATED VANITY MIRRORS — IF EQUIPPED Adjust the convex outside mirror so you can just see the An illuminated vanity mirror is on each sun visor. To use side of your vehicle in the part of the mirror closest to the the mirror, rotate the sun visor down and swing the vehicle.
Page 91: Hands-Free Communication (Uconnect ) - If Equipped
• www.chrysler.com/uconnect NOTE: The sales code RER radio contains an inte- grated Hands-Free Communication (UConnect ) sys- • www.dodge.com/uconnect tem. Refer to your “Navigation User’s Manual” for • www.jeep.com/uconnect UConnect system operating instructions for this radio. • or call 1–877–855–8400...
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE different electronic devices to connect to each other Voice Recognition Button without wires or a docking station, so UConnect works Actual button location may vary with radio. no matter where you stow your cellular phone (be it your The individual buttons are described in the purse, pocket, or briefcase), as long as your phone is “Operation”...
Page 93: Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 • For each feature explanation in this section, only the The radio display will be used for visual prompts from the UConnect system such as CELL or caller ID on combined form of the voice command is given. You certain radios.
Page 94 94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To activate the UConnect system from idle, simply press The following are general phone to UConnect system the PHONE button and follow audible prompts for pairing instructions: directions. All UConnect system sessions begin with a •...
Page 95 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 • You will then be asked to give your cellular phone a Dial by Saying a Number priority level between 1 and 7, with 1 being the highest • Press the PHONE button to begin. priority.
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call by Saying a Name Add Names to Your UConnect Phonebook • Press the PHONE button to begin. NOTE: Adding names to the phonebook is recom- mended when the vehicle is not in motion. •...
Page 97 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 After you are finished adding an entry into the phone- Object Exchange Profile (OBEX). Please see your phone book, you will be given the opportunity to add more owners’ manual for specific instructions on how to send phone numbers to the current entry or to return to the these entries from your phone.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Edit Entries in the UConnect Phonebook Phonebook Edit can be used to add another phone number to a name entry that already exists in the NOTE: Editing names in the phonebook is recom- phonebook.
Page 99 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 • After confirmation, the phonebook entries will be from which you choose. To select one of the entries from the list, press the VOICE RECOGNITION button deleted. while the UConnect system is playing the desired •...
Page 100: Phone Call Features
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The UConnect system will then prompt you as to the the call, press and hold the PHONE button until you hear number designation you wish to call. a single beep, indicating that the incoming call was rejected.
Page 101 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Making a Second Call While Current Call in indicating that the active and hold status of the two calls Progress have switched. Only one call can be placed on hold at one To make a second call while you are currently on a call, time.
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Termination Call Continuation To end a call in progress, momentarily press the PHONE Call continuation is the progression of a phone call on the button. Only the active call(s) will be terminated and if UConnect system after the vehicle ignition key has been there is a call on hold, it will become the new active call.
Page 103: Uconnect System Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 Emergency Assistance UConnect System Features If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the UConnect system is • Pick up the phone and manually dial the emergency using: number for your area.
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE United States of America and Canada and 060 for NOTE: The Towing Assistance number dialed is based Mexico). The number dialed may not be applicable with on the country where the vehicle is purchased (1-800-528- the available cellular service and area.
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Working with Automated Systems a number, or sequence of numbers, followed by Send, is This method is used in instances where one generally has also to be used for navigating through an automated to press numbers on the cellular phone keypad while customer service center menu structure, and to leave a navigating through an automated telephone system.
Page 106 106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Some paging and voice mail systems have system time • After the Ready prompt and the following beep, say out settings, too short, that may not allow the use of Setup Confirmations. The UConnect system will this feature.
Page 107: Advanced Phone Connectivity
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 phone, the audio will be played through your vehicle’s In order to un-mute the UConnect system: audio system. The UConnect system will work the same • Press the VOICE RECOGNITION button. as if you dial the number using voice recognition. •...
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you would like to connect or disconnect the Bluetooth Select Another Cellular Phone connection between a UConnect paired cellular phone This feature allows you to select and start using another and the UConnect system, follow the instructions de- phone paired with the UConnect system.
Page 109: Things You Should Know About Your Uconnect System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Delete UConnect Paired Cellular Phones Voice Training For users experiencing difficulty with the system recog- • Press the PHONE button to begin. nizing their voice commands or numbers, the UConnect • After the Ready prompt and the following beep, say system Voice Training feature may be used.
Page 110 110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Performance is maximized under: This procedure may be repeated with a new user. The system will adapt to the last trained voice only. • low-to-medium blower setting, To restore the voice recognition system to factory default •...
Page 111 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 • It is not recommended to store similar sounding • low-to-medium vehicle speed, names in the UConnect phonebook. • low road noise, • UConnect phonebook nametag recognition rate is • smooth road surface, optimized for the person who stored the name in the •...
Page 112 112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Bluetooth Communication Link Power-Up Cellular phones have been found to lose connection to After switching the ignition key from OFF to either ON the UConnect system. When this happens, the connec- or ACC position, or after a language change, you must tion can generally be re-established by switching the wait at least five seconds prior to using the system.
Page 113 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113...
Page 114 114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 115 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115...
Page 116 116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 117 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
Page 118: General Information
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE General Information NOTE: In a stressful situation, take care to speak into This device complies with part 15 of the FCC rules and the Voice Interface System as calmly and normally as RSS 210 of Industry Canada. Operation is subject to the possible.
Page 119: Commands
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the VR hard-key, listen for the beep, and dows are closed, and the heater/air-conditioning fan is say your command.
Page 120 120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • FREQUENCY (to change the frequency) 3. Use the ON/OFF VOLUME rotary knob to adjust the volume to a comfortable level while the voice recognition • NEXT STATION (to select the next station) system is speaking.
Page 121 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 Satellite Radio Disc To switch to satellite radio mode say SAT or SATELLITE To switch to the disc mode say DISC. In this mode, you RADIO. In this mode, you may say the following com- may say the following commands: mands: •...
Page 122: Voice Training
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE − CONTINUE (to continue recording) Voice Training For users experiencing difficulty with the system recog- − DELETE (to delete the recording) nizing their voice commands or numbers, the UConnect • PLAY MEMOS (to play previously recorded memos) system Voice Training feature may be used.
Page 123: Seats
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 SEATS Manual Front Seat Adjustments Forward/Rearward The adjusting bar is at the front of the seats, near the floor. Pull the bar up to move the seat to the desired position. Manual Seat Adjusting Bar After releasing the adjusting bar, apply forward and rearward body pressure to be sure the seat is latched.
Page 124 124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE mechanism, located on the outboard side of the seat, back to the desired position and release the lever. Lean raises and lowers it. Total travel is 2.2 in. (56 mm). forward and lift the lever to return the seatback to its normal position.
Page 125 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125 Lumbar Support — If Equipped WARNING! This feature allows you to increase or decrease the amount of lumbar support. The control lever is located • Adjusting a seat while the vehicle is moving is on the outboard side of the driver’s seatback.
Page 126: Power Seats - If Equipped
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped CAUTION! The power seat switches are on the outboard side of the seat near the floor. Use the front switch to move the seat Do not place any article under a power seat as it may up, down, forward, rearward, or to tilt the seat.
Page 127: Fold-Flat Front Passenger Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 This feature heats leather or cloth front driver and FOLD-FLAT FRONT PASSENGER SEAT passenger seats. The controls for the heated seats are The recline handle on the front passenger seat also located in the center console below the climate controls. releases the seatback to fold forward.
Page 128: Adjustable Head Restraints
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The hard seatback features a work surface and a molded ADJUSTABLE HEAD RESTRAINTS rim for retaining items stored on the seat back panel. Head restraints can reduce the risk of whiplash injury in the event of impact from the rear.
Page 129: Folding Rear Seat
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 FOLDING REAR SEAT WARNING! To provide additional storage area, the rear seatback can be folded forward. Pull on the loops shown in the picture The rear cargo area of the vehicle (with the rear to fold down either or both seatbacks.
Page 130: Folding Rear Seat Center Armrest
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE FOLDING REAR SEAT CENTER ARMREST TO OPEN AND CLOSE THE HOOD The rear seat is equipped with a folding armrest with cup To open the hood, two latches must be released. First pull holders.
Page 131 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 Hood Safety Catch Hood Prop Rod Hole Location Use the hood prop rod to secure the hood in the open Before closing the hood, make sure to stow the prop rod position. Place the upper end of the prop rod in the hole in its proper location.
Page 132: Lights
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched it could fly up when the vehicle is moving and block your forward vision. You could have a collision. Be sure all hood latches are fully latched before driving. LIGHTS MAP/READING/INTERIOR LIGHTS These lights are mounted between the sun visors above...
Page 133: Multi-Function Control Lever
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 because a door is open. This includes the glove box light, HEADLIGHTS; PARKING LIGHTS; INSTRUMENT but not the trunk light. To restore interior light operation, LIGHTS either turn the ignition switch ON or cycle the light Turn the end of the Multi-Function Control Lever to the switch.
Page 134: Automatic Headlight System - If Equipped
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To change the brightness of the instrument panel lights, AUTOMATIC HEADLIGHT SYSTEM — IF rotate the center portion of the Multi-Function Control EQUIPPED Lever up or down. Turning the end of the multi-function control lever to the third detent, “A”...
Page 135: Passing Light / Flash-To-Pass
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 NOTE: On this vehicle, the daytime running light will PASSING LIGHT / FLASH-TO-PASS You can signal another vehicle with your headlights by automatically turn off when the turn signal is in opera- lightly pulling the Multi-Function Control Lever toward tion and automatically turn back on when the turn signal you.
Page 136: Turn Signals
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TURN SIGNALS Move the Multi-Function Control Lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. You can signal a lane change by moving the lever partially up or down without moving beyond the detent.
Page 137: Highbeam/Lowbeam Select Switch
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 If either light remains on and does not flash, or there is a very fast flash rate, check for a defective outside light bulb. If an indicator fails to light when the lever is moved, it would suggest that the fuse or indicator bulb is defective.
Page 138: Windshield Wipers And Washers
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS Rotate the end of the lever to the first detent past the The wipers and washers are operated by a switch intermittent settings for Low-speed wiper operation, or on the control lever. The lever is located on the to the second detent past the intermittent settings for right side of the steering column.
Page 139: Intermittent Wiper System
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Intermittent Wiper System CAUTION! Use the intermittent wiper system when weather condi- tions make a single wiping cycle with a variable pause • Turn the windshield wipers off when driving between cycles desirable. Rotate the end of the Wind- through an automatic car wash.
Page 140: Mist Feature
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OFF position. If the windshield wiper switch is turned OFF and the blades cannot return to the OFF position, damage to the wiper motor may occur. WARNING! Sudden loss of visibility through the windshield could lead to an accident.
Page 141: Windshield Washers
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 addition, the headlights will turn OFF when the wipers If you activate the washer while the wiper control is in are turned off if they were turned on by this feature. the OFF position, the wipers will operate for two wipe cycles and then turn OFF.
Page 142: Tilt/Telescoping Steering Column
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Commercially available windshield washer solvents are flammable. They could ignite and burn you. Care must be exercised when filling or working around the washer solution. TILT/TELESCOPING STEERING COLUMN This feature allows you to tilt the steering column upward or downward.
Page 143: Electronic Speed Control - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 outward or push it inward as desired. To lock the steering ELECTRONIC SPEED CONTROL OPERATION column in position, push the control handle inward until The Speed Control Lever is located on the right side of fully engaged.
Page 144: To Activate
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TO ACTIVATE: TO SET AT THE DESIRED SPEED: Push the ON/OFF button located in the end of the When the vehicle has reached the desired speed, press Electronic Speed Control Lever. The Speed Control indi- down on the lever and release (SET DECEL).
Page 145: To Resume Speed
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Tapping the “SET DECEL” button once will result in a 1 TO RESUME SPEED: To resume a previously set speed, push the “RESUME mph (2 km/h) speed decrease. Each time the button is ACCEL”...
Page 146: Garage Door Opener - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using Speed Control on Hills NOTE: The speed control system maintains speed up and down hills. A slight speed change on moderate hills is normal. On steep hills, a greater speed loss or gain may occur so it may be preferable to drive without speed control.
Page 147: Programming Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! WARNING! Your motorized door or gate will open and close while Vehicle exhaust contains carbon monoxide, a danger- you are training the Universal Transceiver. Do not train ous gas. Do not run your vehicle in the garage while the transceiver if people or pets are in the path of the training the transceiver.
Page 148 148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Your vehicle should be parked outside of the garage NOTE: • Some gate operators and garage door openers may when programming. require you to replace Step 3 with procedures noted in 1. Turn the ignition switch to the ON/RUN position. the “Gate Operator/Canadian Programming”...
Page 149 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 If the indicator light blinks rapidly for two seconds, and then turns to a constant light, continue with program- ming for a Rolling Code. 5. PROGRAMMING A ROLLING CODE SYSTEM At the garage door opener motor (in the garage), locate the “Learn”...
Page 150: Gate Operator/Canadian Programming
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 7. Return to the vehicle and press the programmed Similar to this Canadian law, some U.S. gate operators are HomeLink button twice (holding the button for two designed to “time-out” in the same manner. seconds each time).
Page 151: Using Homelink
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Then proceed with Step 4 under “Programming 2. Press and hold the desired HomeLink button until HomeLink ” earlier in this section. the indicator light begins to flash after 20 seconds. Do not release the button.
Page 152: Troubleshooting Tips
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Troubleshooting Tips General Information If you are having trouble programming HomeLink , here This device complies with FCC rules Part 15 and Industry are some of the most common solutions: Canada RSS-210. Operation is subject to the following two conditions: •...
Page 153: Power Sunroof - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 POWER SUNROOF — IF EQUIPPED WARNING! The sunroof controls are mounted between the sun visors in the Dome/Reading Lamp. • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
Page 154: Opening Sunroof - Manual
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Opening Sunroof - Manual Venting Sunroof - Express Press the switch rearward and hold, and the sunroof will Press and release the V button, and the sunroof will open automatically from any position. The sunroof will open to the vent position.
Page 155: Sunshade Operation
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Sunshade Operation Sunroof Maintenance The sunshade can be opened manually. However, the Use only a non abrasive cleaner and a soft cloth to clean sunshade will open automatically as the sunroof opens. the glass panel. NOTE: The sunshade cannot be closed if the sunroof is Ignition Off Operation open.
Page 156: Electrical Power Outlets
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS There are two 12-volt electrical outlets on this vehicle. Both of the outlets are protected by a fuse. The instrument panel power outlet, located below the climate control knobs, has power available only when the ignition is on.
Page 157: Electrical Outlet Use With Engine Off
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 The center console power outlet is powered directly from Electrical Outlet Use With Engine Off the battery (power available at all times). Items plugged CAUTION! into this outlet may discharge the battery and/or prevent engine starting.
Page 158: Cigar Lighter And Ash Receiver - If Equipped
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CIGAR LIGHTER AND ASH RECEIVER — IF EQUIPPED Cup Holder Ash Receiver — If Equipped An optional ash receiver is available from your autho- rized dealer and will fit in either one of the center console cup holders.
Page 159: Console Features
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 holders will also accommodate large size cups and 20 oz. CAUTION! bottles. (An optional removable ashtray may be located in the one cup holder.) For vehicles equipped with the heated and cooled cup holder, locate the cup holder ash receiver in the forward cup holder.
Page 160 160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Left Latch opens to the top storage area. Dual Storage Bins Lifting a latch at the front of the hinged armrest provides • The lower bin can be accessed directly, without first access to these storage areas.
Page 161 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 Video Console — If Equipped The optional VES™(Video Entertainment System) in- cludes the following components: • The screen for a rear seat DVD player is stored under the armrest. • Remote Control • Audio/Video RCA Jacks Video Console See Section Four, “Video Entertainment System-If Equipped,”...
Page 162: Cup Holders
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUP HOLDERS Heated or Cooled Cup Holder — If Equipped With this feature the rear cavity of the cup holder can keep cool beverages cool, and hot beverages hot. The rear cup holder heats to 140°F (60°C) or cools to 35°F (1.6°C). The switch is located on the front of the center console and has three positions: HEAT, OFF, COOL.
Page 163: Rear Bottle Holders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 CAUTION! Make sure the beverage container can withstand the temperatures shown above, when using the Cooled or Heated Cup Holder. Rear Bottle Holders There are built-in bottle holders located in both rear door trim panels.
Page 164: Storage
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! • Be certain that the seatback is securely locked into If containers of hot liquid are placed in the bottle position. If the seatback in not securely locked holder, they can spill when the door is closed, burn- into position, the seat will not provide the proper ing the occupants.
Page 165: Beverage Cooler Storage Bin - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 BEVERAGE COOLER STORAGE BIN — IF WARNING! EQUIPPED The Beverage Cooler Storage Bin is located in the top of • The weight and position of cargo and passengers the instrument panel on the passenger side. A recessed can change the vehicle center of gravity and ve- latch at the front releases the bin door and swings up for hicle handling.
Page 166 166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The cooling bin will hold up to four, standing, 12 ounce, The Glove Compartment is located beneath the beverage beverage cans. The cooler bin is also equipped with a soft bin. The glove compartment door swings downward for molded liner that is removable for easy cleaning.
Page 167 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....171 Compass Display ..... 190 Instrument Cluster—Base .
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL Sales Code REQ — AM/FM Stereo Radio And Operating Instructions — Voice Recognition 6–Disc CD/DVD Changer (MP3/WMA AUX System (VR) (If Equipped) ....213 Jack) .
Page 169 UNDERSTANDING YOUR INSTRUMENT PANEL 169 Play Mode ......220 Operating Instructions - Video Entertainment System (VES™) (If Equipped) ... . . 228 List Or Browse Mode .
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips ..... . . 245 Electric Rear Window Defroster — If Equipped ......249 Rear Window Features .
Page 171: Instrument Panel Features
UNDERSTANDING YOUR INSTRUMENT PANEL 171 INSTRUMENT PANEL FEATURES Instrument Panel Features...
Page 172: Instrument Cluster-Base
172 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER—BASE...
Page 173: Instrument Cluster-Premium
UNDERSTANDING YOUR INSTRUMENT PANEL 173 INSTRUMENT CLUSTER—PREMIUM...
Page 174: Instrument Cluster Descriptions
174 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS If the pointer rises to the H (red) mark, the instrument cluster will sound a chime. Pull over and stop the vehicle. 1. Fuel Gauge Idle the vehicle with the air conditioner turned off until When the ignition switch is in the ON position, the the pointer drops back into the normal range.
Page 175 UNDERSTANDING YOUR INSTRUMENT PANEL 175 5. Low Fuel Light come on during starting, stays on, or comes on while When the fuel level drops to 2 gallons, the fuel driving, have the system checked by an authorized symbol will light and a single chime will sound. dealer.
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL will turn off after the engine is started. If the bulb does 13. Tachometer not come on during starting, have the system checked by The white area of the scale shows the permissible engine an authorized dealer. revolutions-per-minute (rpm x 1000) for each gear range.
Page 177 UNDERSTANDING YOUR INSTRUMENT PANEL 177 The two trip odometers show individual trip mileage. To gASCAP switch from odometer to trip odometers, press and If the vehicle diagnostic system detects a leak or change release the Trip Odometer button. To reset a trip odom- in the evaporative system, or the fuel filler cap is loose, eter, display the desired trip odometer to be reset then improperly installed, or damaged, the words “gASCAP”...
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL indicator system is duty cycle based, which means the NOTE: If the indicator message illuminates when you engine oil change interval may fluctuate dependent upon start the vehicle, the oil change indicator system did not your personal driving style.
Page 179 UNDERSTANDING YOUR INSTRUMENT PANEL 179 Dual Trip Odometer — If Equipped If the light is flashing when the engine is running you may experience power loss, an elevated/rough idle, and Press and release this button to change the display from increased brake pedal effort, and your vehicle may odometer to “Trip A.”...
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL 20. Turn Signal Indicators 23. All Wheel Drive (AWD) The arrows will flash in unison with the exterior This indicator lights when AWD is selected. turn signal, when using the turn signal lever. 21. Front Fog Light Indicator — If Equipped This light shows when the front fog lights are ON.
Page 181 UNDERSTANDING YOUR INSTRUMENT PANEL 181 Accordingly, when the low tire pressure telltale illumi- illuminated. This sequence will continue upon subse- nates, you should stop and check your tires as soon as quent vehicle start-ups as long as the malfunction exists. possible, and inflate them to the proper pressure.
Page 182 182 UNDERSTANDING YOUR INSTRUMENT PANEL 25. Malfunction Indicator Light CAUTION! This light is part of an onboard diagnostic system called OBD that monitors emissions, engine, and The TPMS has been optimized for the original automatic transaxle control systems. The light equipment tires and wheels.
Page 183 UNDERSTANDING YOUR INSTRUMENT PANEL 183 could lead to immediate loss of power or severe catalytic The ABS warning light should be checked frequently to converter damage. The vehicle should be serviced as assure that it is operating properly. Turn the ignition key soon as possible if this occurs.
Page 184 184 UNDERSTANDING YOUR INSTRUMENT PANEL The dual brake system provides a reserve braking capac- WARNING! ity in the event of a failure to a portion of the hydraulic system. Failure of either half of the dual brake system is Driving a vehicle with the brake light on is danger- indicated by the Brake Warning Light which will turn on ous.
Page 185: Electronic Vehicle Information Center (Evic) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 185 the parking brake is applied or a brake fault is detected. ELECTRONIC VEHICLE INFORMATION CENTER If the light does not illuminate, have the light inspected (EVIC) – IF EQUIPPED by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON position.
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL • System Status Press and release the MENU button to advance the display to Trip Functions or Personal Set- • Vehicle information warning message displays tings or to return to the default System Status • Personal Settings (customer programmable features) display.
Page 187: Displays
UNDERSTANDING YOUR INSTRUMENT PANEL 187 • Right Rear Turn Signal Light Out (with a single chime) Press and release the RESET Button to accept a selection. The RESET Button also resets various • RKE (Remote Keyless Entry) Battery Low (with a Trip Functions.
Page 188: Oil Change Required
188 UNDERSTANDING YOUR INSTRUMENT PANEL Oil Change Required 2. Fully depress the accelerator pedal slowly three times Your vehicle is equipped with an engine oil change within 10 seconds. indicator system. The “Oil Change Required” message 3. Turn the ignition switch to the “LOCK” position. will flash in the EVIC display for approximately 10 seconds after a single chime has sounded to indicate the NOTE: If the indicator message illuminates when you...
Page 189 UNDERSTANDING YOUR INSTRUMENT PANEL 189 The Trip Functions mode displays the following informa- NOTE: Significant changes in driving style or vehicle tion: loading will greatly affect the actual drivable distance of the vehicle, regardless of the DTE display value. • Average Fuel Economy •...
Page 190: Compass Display
190 UNDERSTANDING YOUR INSTRUMENT PANEL To Reset The Display Automatic Compass Calibration Reset will only occur if a resettable function is currently This compass is self-calibrating, which eliminates the displayed. Press and hold the RESET button once to clear need to calibrate the compass manually. When the ve- the function currently displayed.
Page 191 UNDERSTANDING YOUR INSTRUMENT PANEL 191 1. Start the engine. Leave the selector lever in “P” (Park) Compass Variance in order to enter the EVIC Programming Menus. Compass Variance is the difference between magnetic North and Geographic North. In some areas of the 2.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL 1. Turn the ignition switch to the “ON” position. Leave the selector lever in “P” (Park). 2. Press and release the MENU button until “Personal Settings” displays in the EVIC. 3. Press and release the STEP button until “Compass Variance”...
Page 193: Personal Settings (Customer Programmable Features)
UNDERSTANDING YOUR INSTRUMENT PANEL 193 Auto Unlock on Exit Personal Settings (Customer Programmable Features) When ON is selected, all doors will unlock when the Personal Settings allows the driver to set and recall vehicle is stopped and the transaxle is in the “P” (Park) or features when the automatic transaxle is in “P”...
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Sound Horn with Lock when exiting the vehicle. To make your selection, press When ON is selected, a short horn sound will occur when and hold the RESET button until “0,” “30,” “60,” or “90” the remote keyless entry “Lock”...
Page 195: Radio General Information
UNDERSTANDING YOUR INSTRUMENT PANEL 195 power outlets will remain active for up to 10 minutes RADIO GENERAL INFORMATION after the ignition switch is turned to the LOCK position. Radio Broadcast Signals Opening a vehicle door will cancel this feature. To make The radio will provide excellent reception under most your selection, press and hold the RESET button until operating conditions.
Page 196: Electrical Disturbances
196 UNDERSTANDING YOUR INSTRUMENT PANEL Electrical Disturbances NOTE: The radio, steering wheel radio controls (if Radio waves may pick up electrical disturbances during equipped), and 6–Disc CD/DVD changer (if equipped) transmission. They mainly affect the wave amplitude, will remain active for up to 10 minutes after the ignition and thus remain a part of the AM reception.
Page 197: Operating Instructions - Radio Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 197 Power Switch/Volume Control (Rotary) Push the ON/VOLUME control knob to turn on the radio. Press the ON/VOLUME control knob a second time to turn off the radio. Electronic Volume Control The electronic volume control turns continuously (360 degrees) in either direction without stopping.
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button Phone Button (UConnect Hands-Free Phone) — If Pressing the SCAN button causes the tuner to search for Equipped the next listenable station, in AM, FM or Satellite (if Press this button to operate the Hands-Free Phone equipped) frequencies, pausing for five seconds at each (UConnect ) feature (if equipped).
Page 199 UNDERSTANDING YOUR INSTRUMENT PANEL 199 3. After adjusting the hours, press the right side TUNE/ RW/FF SCROLL control knob to set the minutes. The minutes Pressing the RW (Rewind) or FF (Fast Forward) buttons will begin to blink. causes the tuner to search for the next frequency in the direction of the arrows.
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob a third or turning the TUNE/SCROLL control knob within five time and TREBLE will display. Turn the TUNE/SCROLL seconds will allow the program format type to be se- control knob to the right or left to increase or decrease the lected.
Page 201 UNDERSTANDING YOUR INSTRUMENT PANEL 201 By pressing the SEEK button when the Music Type icon Program Type 16–Digit Character Display is displayed, the radio will be tuned to the next frequency News News station with the same selected Music Type name. The Nostalgia Nostalga Music Type function only operates when in the FM...
Page 202 202 UNDERSTANDING YOUR INSTRUMENT PANEL • DVD Enter - When the disc is in DVD Menu mode, • Angle – Repeatedly pressing SELECT will change selecting DVD Enter will allow you to play the current the viewing angle if supported by the DVD disc (if highlighted selection.
Page 203 UNDERSTANDING YOUR INSTRUMENT PANEL 203 • Set Home Clock - Pressing the SELECT button will Audio Language — If Equipped allow user to set the clock. Turn the TUNE/SCROLL Selecting this item allows you to choose a default audio control knob to adjust the hours and then press and language (effective only if the language is supported by turn the TUNE/SCROLL control knob to adjust the the disc).
Page 204 204 UNDERSTANDING YOUR INSTRUMENT PANEL Audio DRC — If Equipped a disc is loaded, changes will not be effective. Also, the defaults are effective only if the disc supports the Selecting this item allows you to limit maximum audio customer-preferred settings. dynamic range.
Page 205: Operation Instructions - (Disc Mode For Cd And Mp3/Wma Audio Play, Dvd-Video)
UNDERSTANDING YOUR INSTRUMENT PANEL 205 both AM and FM. This allows a total of 12 AM, 12 FM, Operation Instructions - (DISC MODE for CD and and 12 Satellite (if equipped) stations to be stored into MP3/WMA Audio Play, DVD-VIDEO) pushbutton memory.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) position to operate the radio. Press the eject button and the pushbutton with the corresponding number (1-6) where the CD LOAD Button —...
Page 207: Notes On Playing Mp3/Wma Files
UNDERSTANDING YOUR INSTRUMENT PANEL 207 SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL The radio uses the following limits for file systems: If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ • Maximum number of directory levels: 8 WMA tracks on that disc.
Page 209 UNDERSTANDING YOUR INSTRUMENT PANEL 209 Playlist files are not supported. MP3 Pro files are not MPEG Specifi- Sampling Fre- Bit Rate (kbps) supported. cation quency (kHz) 320, 256, 224, Playback of MP3/WMA Files MPEG-1 Audio 192, 160, 128, When a medium containing MP3/WMA data is loaded, 48, 44.1, 32 Layer 3 112, 96, 80, 64,...
Page 210: List Button
210 UNDERSTANDING YOUR INSTRUMENT PANEL To increase the speed of disc loading, it is recommended INFO Button (DISC Mode for MP3/WMA Play) to use CD-R media and single-session discs. To create a Pressing the INFO button repeatedly will scroll through single-session disc, enable the “Disc at Once”...
Page 211 UNDERSTANDING YOUR INSTRUMENT PANEL 211 Pressing the AUX button will change the mode to auxil- TIME Button (Auxiliary Mode) iary device if the AUX jack is connected. Press the TIME button to change the display from elapsed playing time to time of day. The time of day will NOTE: The AUX device must be turned on and the display for five seconds.
Page 212: Sales Code Ren - Multimedia System - If Equipped
212 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Hands-Free Phone Macrovision This product incorporates copyright protection technol- (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )” in ogy that is protected by U.S. patents and other intellec- Section 3 of this manual. tual property rights.
Page 213: Operating Instructions - Satellite Radio (If Equipped)
UNDERSTANDING YOUR INSTRUMENT PANEL 213 “JukeBox” (virtual CD changer). Sirius Satellite Radio is vehicles equipped with a backup camera, and on some optional. The 6.5-in touch screen allows for easy menu models a dual display screen operation. Refer to your selection.
Page 214: Operating Instructions - Hands-Free Communication (Uconnect ) (If Equipped)
214 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Hands-Free 4. To move the minute forward, touch the screen where the word “Min” with the arrow pointing upward is Communication (UConnect ) (If Equipped) Refer to “Hands-Free Communication (UConnect )” in displayed.
Page 215 UNDERSTANDING YOUR INSTRUMENT PANEL 215 3. When this feature is on, a check mark will appear in Changing the Time Zone the box next to the words “Daylight Savings.” Touch the 1. Turn on the system. screen where the words “Daylight Savings” are dis- played to change the current setting.
Page 216: Sales Code Rer - Multimedia System - If Equipped
216 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RER — MULTIMEDIA SYSTEM — IF integrated color screen to provide maps, turn identifica- tion, selection menus, and instructions for selecting a EQUIPPED variety of destinations and routes. NOTE: The sales code is located on the lower right side of the unit’s faceplate.
Page 217: Operating Instructions - Satellite Radio
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Other special features include direct tune, music type Clock Setting Procedure selections, traffic messaging (optional), easy store presets, The GPS receiver in this system is synchronized to the parental lockout for VES™ (if equipped), backup camera time data being transmitted by the GPS satellites.
Page 218 218 UNDERSTANDING YOUR INSTRUMENT PANEL 4. Touch the screen where the words “Set Time Zone” are 3. When this feature is on, a check mark will appear in displayed. The time zone selection menu will appear on the box next to the words “Daylight Savings.” Touch the the screen.
Page 219: Universal Consumer Interface (Uci) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 219 4. To move the hour forward, touch the screen where the 1. Turn on the system. word “Hour” with the arrow pointing upward is dis- 2. Touch the screen where the time is displayed. The played.
Page 220: Connecting The Ipod Device
220 UNDERSTANDING YOUR INSTRUMENT PANEL Using this feature, Controlling The iPod Using Radio Buttons To get into the UCI (iPod ) mode and access a connected • the iPod audio can be played on the vehicle’s sound iPod , press the AUX button on the radio faceplate. Once system, providing metadata (Track Title, Artist, Al- in the UCI (iPod ) mode, the iPod audio track (if...
Page 221 UNDERSTANDING YOUR INSTRUMENT PANEL 221 Turning it clockwise (forward) by one click while playing Pressing and releasing the FF button will go forward five a track skips to the next track. seconds of the current track. Turning it counterclockwise (backward) by one click SEEK Buttons during the first two seconds of the track will jump to the Use the SEEK buttons to move to the previous or the next...
Page 222: List Or Browse Mode
222 UNDERSTANDING YOUR INSTRUMENT PANEL of the screens, the last press of the INFO button will take List or Browse Mode you back to the play mode screen on the radio. During Play mode, pressing any of the following buttons will take you to List mode.
Page 223 UNDERSTANDING YOUR INSTRUMENT PANEL 223 During all List modes, the iPod will display all lists in After pressing a preset button, you will see the list you “wrap-around” mode. So if the track you wish to select is are in on the top line and the first item in that list on the at the bottom of the list, you just turn the “TUNE/ second line.
Page 224: Satellite Radio (Rsc) - If Equipped (Rer/Req/Ren Radios Only)
224 UNDERSTANDING YOUR INSTRUMENT PANEL SATELLITE RADIO (RSC) — IF EQUIPPED web site at www.sirius.com, or at www.siriuscanada.ca for Canadian residents. Please have the following infor- (RER/REQ/REN RADIOS ONLY) Satellite radio uses direct satellite-to-receiver broadcast- mation available when calling: ing technology to provide clear digital sound, coast to 1.
Page 225: Selecting Satellite Mode
UNDERSTANDING YOUR INSTRUMENT PANEL 225 Sirius ID number will display. The Sirius ID number Reception Quality display will time out in two minutes. Press any button on Satellite reception may be interrupted due to one of the the radio to exit this screen. following reasons: •...
Page 226 226 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons three seconds will make the radio display the Song Title Press and release the SEEK buttons to search for the next all of the time (press and hold again to return to normal channel in Satellite mode.
Page 227 UNDERSTANDING YOUR INSTRUMENT PANEL 227 Toggle the MUSIC TYPE button again to select the music type. The symbol SET 1 will now show in the display window. Select the button (1-6) you wish to lock onto this channel By pressing the SEEK button when the Music Type and press and release that button.
Page 228: Operating Instructions - Hands-Free Phone (If Equipped)
228 UNDERSTANDING YOUR INSTRUMENT PANEL Buttons 1 - 6 These buttons tune the radio to the channels that you commit to pushbutton memory {12 Satellite stations}. Operating Instructions - Hands-Free Phone (If Equipped) Refer to “Hands-Free Communication (UConnect )” in Section 3 of this manual.
Page 229: Operation With Rer Multi-Media System
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • Press the button in the center of the switch to select beginning of the previous track if it is within one AM, FM, Satellite (SAT) - if equipped, or CD (DISC) second after the current track begins to play. mode.
Page 230: Video Entertainment System - If Equipped
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Press the switch up or down twice to listen to the Left-Hand Switch Functions for Radio Operation second track on the CD, three times to listen to the • Press the top of the switch to SEEK the next listenable third track, and so forth.
Page 231 UNDERSTANDING YOUR INSTRUMENT PANEL 231 Opening the Rear Seat Video Entertainment System VES™ Video Screen • The LCD Screen swings up from the rear of the NOTE: Close the armrest after the LCD screen has been armrest to allow the rear seat passenger(s) to view the raised to its viewing position.
Page 232 232 UNDERSTANDING YOUR INSTRUMENT PANEL • A battery-powered infrared remote control that snaps • Two wireless infrared headsets allow rear seat passen- into a molded compartment in the center console gers to listen to the same or individual audio sources. armrest upper storage bin.
Page 233: Radio Operation And Cellular Phones
UNDERSTANDING YOUR INSTRUMENT PANEL 233 2. If the disc is stained, clean the surface with a soft cloth, RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the cellular phone being ON in wiping from center to edge. your vehicle can cause erratic or noisy performance from 3.
Page 234: Climate Controls
234 UNDERSTANDING YOUR INSTRUMENT PANEL CLIMATE CONTROLS Blower Control The Air Conditioning and Heating System is designed to Rotate this control to regulate make you comfortable in all types of weather. the amount of air forced through the ventilation sys- Manual Air Conditioning and Heating System tem in any mode.
Page 235 UNDERSTANDING YOUR INSTRUMENT PANEL 235 Temperature Control Mode Control (Air Direction) Rotate this control to regulate Rotate this control to choose the temperature of the air in- from several patterns of air side the passenger compart- distribution. You can select ei- ment.
Page 236 236 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Air is directed through the panel and floor outlets. Air is directed through the floor, defrost, and side window demist outlets. This setting works best in cold or snowy conditions that require extra heat to NOTE: For all settings except full cold or full hot, there the windshield.
Page 237 UNDERSTANDING YOUR INSTRUMENT PANEL 237 Recirculation Control NOTE: • Continuous use of the recirculation mode may make Press in on this button to block the flow of outside air the inside air stuffy and window fogging may occur. from coming into the passen- Extended use of this mode is not recommended.
Page 238 238 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Control NOTE: The air conditioning compressor will not engage Press in on this button to en- until the engine has been running for about 10 seconds. gage the Air Conditioning. A • MAX A/C light will illuminate when the For maximum cooling use the A/C and recirculation Air Conditioning System is...
Page 239: Automatic Temperature Control (Atc) - If Equipped
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Automatic Operation Automatic Temperature Control (ATC) — If Equipped The Infrared Climate Control System automatically maintains the climate in the cabin of the vehicle at the comfort levels desired by the driver and passenger. To accomplish this, the system gathers information from the cabin infrared sensor mounted between the sun-visors and from various sensors located throughout the vehicle.
Page 240 240 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: The AUTO position performs best for front seat 72°F (22°C) is the recommended setting for maximum occupants only. comfort for the average person; however, this may vary. 2. Dial in the temperature NOTE: • The temperature setting can be adjusted at any time you would like the system to maintain by rotating the Tem- without affecting automatic operation.
Page 241 UNDERSTANDING YOUR INSTRUMENT PANEL 241 Manual Operation The blower can be set to any fixed blower speed by This system offers a full complement of manual override rotating the Blower Control knob (on the left). features, which consist of Blower Preferred Automatic, NOTE: Please read the Automatic Temperature Control Mode Preferred Automatic, or Blower and Mode Pre- Operation Chart that follows for details.
Page 242 242 UNDERSTANDING YOUR INSTRUMENT PANEL...
Page 243 UNDERSTANDING YOUR INSTRUMENT PANEL 243 The operator can override the AUTO mode setting to NOTE: For all settings except full cold or full hot, there change airflow distribution by rotating the Mode Control is a difference in temperature between the upper and knob (on the right) to one of the following positions.
Page 244 244 UNDERSTANDING YOUR INSTRUMENT PANEL • Defrost system in recirculation mode (ten minutes). This can Air is directed through the windshield and side be used when outside conditions such as smoke, window demist outlets. Use this mode with odors, dust, or high humidity are present. Activating maximum blower and temperature settings for best recirculation will cause the LED in the control button windshield and side window defrosting.
Page 245 UNDERSTANDING YOUR INSTRUMENT PANEL 245 press the Recirculation button to return to outside air. move the Mode Knob to Panel, Panel/Floor and then Some temp/humidity conditions will cause captured press the Recirculation Button. This feature reduces interior air to condense on windows and hamper the possibility of window fogging.
Page 246 246 UNDERSTANDING YOUR INSTRUMENT PANEL Winter Operation windshield and provide sufficient heating. If side win- Use of the air Recirculation mode during winter months dow fogging becomes a problem, increase blower speed. is not recommended because it may cause window Vehicle windows tend to fog on the inside in mild but fogging.
Page 247 UNDERSTANDING YOUR INSTRUMENT PANEL 247 Outside Air Intake A/C Air Filter — If Equipped Make sure the air intake, located directly in front of the The A/C Air Filter will reduce, but not eliminate, diesel windshield, is free of obstructions such as leaves. Leaves and agricultural smells.
Page 248 248 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
Page 249 UNDERSTANDING YOUR INSTRUMENT PANEL 249 REAR WINDOW FEATURES CAUTION! Electric Rear Window Defroster — If Equipped To avoid damaging the electrical conductors of the The electric Rear Window Defroster Control is rear window defroster, do not use scrapers, sharp located on the climate control. Press this button to instruments, or abrasive window cleaners on the turn on the rear window defroster and the heated side interior surface of the window.
Page 251 STARTING AND OPERATING CONTENTS Starting Procedures ..... 256 How To Use Remote Start ....260 Automatic Transaxle .
Page 252 252 STARTING AND OPERATING AutoStick General Information ... 269 Power Steering ......282 All Wheel Drive —...
Page 253 STARTING AND OPERATING 253 Tire Inflation Pressures ....296 Tire Pressure Monitor System (TPMS) — If Equipped ......306 Radial-Ply Tires .
Page 254 254 STARTING AND OPERATING Carbon Monoxide Warnings ....319 Adding Fuel ......324 Flexible Fuel—...
Page 255 STARTING AND OPERATING 255 Trailer Towing Weights (Maximum Trailer Recreational Towing (Behind Motorhome, Etc.) . . 341 Weight Ratings) ..... . 332 Towing This Vehicle Behind Another Vehicle Trailer And Tongue Weight .
Page 256: Starting Procedures
256 STARTING AND OPERATING STARTING PROCEDURES WARNING! Before starting your vehicle, adjust your seat, adjust both inside and outside mirrors, and fasten your seat belt. Be sure to turn off the engine and remove the key Make sure all occupants have securely fastened their seat from the ignition switch if you want to rest or sleep belts.
Page 257: Normal Starting
STARTING AND OPERATING 257 Normal Starting WARNING! Normal Starting of either a cold or a warm engine does not require pumping or depressing the accelerator pedal. Do not attempt to push or tow your vehicle to get it Simply turn the ignition switch to the “START” position started.
Page 258: Tip Start Feature - Automatic Transaxle Only
258 STARTING AND OPERATING Tip Start Feature — Automatic Transaxle Only Extremely Cold Weather (below 20°F or 29°C) To insure reliable starting at these temperatures, use of an Do not press the accelerator. Turn the ignition key briefly externally powered electric engine block heater (available to START position, and release it.
Page 259: After Starting
STARTING AND OPERATING 259 After Starting WARNING! The idle speed will automatically decrease as the engine warms up. Never pour fuel or other flammable liquid into the throttle body air inlet opening in an attempt to start Remote Start System — If Equipped the vehicle.
Page 260: How To Use Remote Start
260 STARTING AND OPERATING How To Use Remote Start To exit the Remote Start mode , allow the To enter the Remote Start mode , depress the Remote engine to run the cycle or depress the unlock Start button twice on the key fob. The engine will start button to disarm the Vehicle Theft Security and the vehicle will remain in the remote start mode for Alarm and within one minute insert the key...
Page 261: Engine Block Heater - If Equipped
STARTING AND OPERATING 261 NOTE: When the vehicle is in the Remote Start mode, ENGINE BLOCK HEATER — IF EQUIPPED power window and sunroof operation are disabled for The engine block heater warms engine coolant and security. permits quicker starts in cold weather. Connect the cord to a standard 110-115 volt AC electrical outlet with a The following conditions must be met before the engine grounded, three-wire extension cord.
Page 262: Automatic Transaxle
262 STARTING AND OPERATING AUTOMATIC TRANSAXLE CAUTION! Damage to the transaxle may occur if the following precautions are not observed: • Shift into PARK only after the vehicle has come to a complete stop. • Shift into or out of REVERSE only after the vehicle has come to a complete stop and the engine is at idle speed.
Page 263: Brake/Transaxle Interlock System
STARTING AND OPERATING 263 Brake/Transaxle Interlock System WARNING! This system prevents you from moving the gear shift out of PARK and into any gear unless the brake pedal is • It is dangerous to shift the selector lever out of pressed.
Page 264: Automatic Transaxle Ignition Interlock System
264 STARTING AND OPERATING • Insert a key, screwdriver, or finger into the front hole feature is inoperable. The engine can be started and then push and hold the manual override release lever stopped, but the key cannot be removed until you obtain forward.
Page 265 STARTING AND OPERATING 265 When parking on a flat surface, place the selector lever in CAUTION! the PARK position first, and then apply the parking brake. DO NOT race the engine when shifting from PARK or NEUTRAL positions into another gear range as When parking on a hill, it is important to set the parking this can damage the drivetrain.
Page 266 266 STARTING AND OPERATING conditions, using the “3” range will improve perfor- WARNING! mance and extend transaxle life by reducing excessive shifting and heat build-up. Do not coast in NEUTRAL and never turn off the ignition to coast down a hill. These are unsafe OVERDRIVE—...
Page 267 STARTING AND OPERATING 267 DRIVE — 4 Speed Transaxle CAUTION! This range eliminates shifts into OVERDRIVE. The trans- axle will operate normally in First, Second, and Third If the transaxle operating temperature exceeds ac- while in this range. The “3” DRIVE range should also be ceptable limits, the vehicle computer will override used when descending steep grades to prevent brake OVERDRIVE and “3”...
Page 268: Autostick - If Equipped
268 STARTING AND OPERATING In the event that the problem has been momentary, the AUTOSTICK — IF EQUIPPED transaxle can be reset to regain all forward gears. AutoStick is a driver-interactive transaxle that offers six manual ratio changes to provide you with more control. 1.
Page 269: Autostick Operation
STARTING AND OPERATING 269 downshift and to the Right (+) an upshift. The gear position will display in the instrument cluster on the transaxle range indicator. NOTE: In Autostick mode, the transaxle will only shift up or down when the driver moves the selector lever to the Right (+) or Left (-).
Page 270: All Wheel Drive - If Equipped
270 STARTING AND OPERATING • Starting out in second gear is helpful in snowy or icy • If the system detects a problem, it will disable the conditions. AutoStick mode and the transaxle will return to the automatic mode until the problem is corrected. •...
Page 271: Parking Brake
STARTING AND OPERATING 271 The system contributes to good fuel economy by operat- NOTE: • This light, when illuminated with parking brake ap- ing only on demand, thereby minimizing power-robbing friction and inertia. plication, shows only that the parking brake is on. It does not show the degree of brake application.
Page 272 272 STARTING AND OPERATING To release the parking brake, slightly pull up the handle NOTE: • When parking on a hill, it is important to set the while pushing the lock button, and guide the lever downward to its stop. The brake warning light in the parking brake before placing the gear selector in park, instrument cluster should go out.
Page 273: Brake System
STARTING AND OPERATING 273 BRAKE SYSTEM WARNING! Your vehicle is equipped with power assisted brakes as standard equipment. In the event power assist is lost for • Never leave children alone in a vehicle. Leaving any reason (i.e. repeated brake applications with the children in a vehicle unattended is dangerous for a engine off) the brakes will still function.
Page 274 274 STARTING AND OPERATING This light monitors various brake functions, WARNING! including brake fluid level and parking brake application. If the brake light turns on, it may • Riding the brakes can lead to brake failure and indicate that the parking brake is applied, that possibly an accident.
Page 275: Anti-Lock Brake System (Abs) - If Equipped
STARTING AND OPERATING 275 ANTI—LOCK BRAKE SYSTEM (ABS) — IF WARNING! EQUIPPED The Anti-Lock Brake System provides increased vehicle • Anti-lock system (ABS) cannot prevent the natural stability and brake performance under most braking laws of physics from acting on the vehicle, nor can conditions.
Page 276 276 STARTING AND OPERATING The ABS light monitors the Anti-Lock Brake When the vehicle is driven over 7 mph (11 km/h), you System. The light will come on when the may also hear a slight clicking sound as well as some ignition switch is turned to the ON position related motor noises.
Page 277: Electronic Brake Control System
STARTING AND OPERATING 277 • and a slight drop or fall away of the brake pedal at the ELECTRONIC BRAKE CONTROL SYSTEM – end of the stop. ABS/TCS/BAS/ESP Your vehicle may be equipped with an optional ad- These are all normal characteristics of ABS. vanced electronic brake control system that includes Anti-Lock Brake System (ABS), Traction Control System WARNING!
Page 278: Traction Control System (Tcs) - If Equipped
278 STARTING AND OPERATING Traction Control System (TCS) — If Equipped Brake Assist System (BAS) — If Equipped This system monitors the amount of wheel spin The BAS is designed to optimize the vehicle’s braking of each of the driven wheels. If wheel spin is capability during emergency braking maneuvers.
Page 279: Electronic Stability Program (Esp)
STARTING AND OPERATING 279 Electronic Stability Program (ESP) WARNING! This system enhances directional control and stability of • BAS cannot prevent the natural laws of physics the vehicle under various driving conditions. ESP cor- from acting on the vehicle, nor can it increase rects for over/under steering of the vehicle by applying braking efficiency beyond that afforded by the the brake of the appropriate wheel to assist in counter-...
Page 280 280 STARTING AND OPERATING ESP/TCS Indicator Light WARNING! The “ESP/TCS Indicator Light,” located in the instru- ment cluster, starts to flash as soon as the tires lose • Electronic Stability Program (ESP) cannot prevent traction and the ESP system becomes active. The “ESP/ the natural laws of physics from acting on the TCS Indicator Light”...
Page 281 STARTING AND OPERATING 281 ESP Operating Modes or gravel conditions and more wheel spin than ESP All ESP equipped vehicles can choose the following ESP would normally allow is required to gain traction. operating modes: To turn ESP on again, momentarily depress the “ESP Control Switch.”...
Page 282: Power Steering
282 STARTING AND OPERATING overcome, turn ESP on again by momentarily depressing NOTE: • The “ESP Indicator Light” and the “ESP/BAS Warning the “ESP Control Switch.” This may be done while the vehicle is in motion. Light” come on momentarily each time the ignition switch is turned ON.
Page 283 STARTING AND OPERATING 283 If for some reason the power assist is interrupted, it will WARNING! still be possible to steer your vehicle. Under these condi- tions, you will observe a substantial increase in steering Continued operation with reduced power steering effort, especially at very low vehicle speeds and during assist could pose a safety risk to yourself and others.
Page 284: Driving On Slippery Surfaces
284 STARTING AND OPERATING DRIVING ON SLIPPERY SURFACES Traction When driving on wet or slushy roads, it is possible for a Acceleration wedge of water to build up between the tire and road Rapid acceleration on snow covered, wet, or other slip- surface.
Page 285: Driving Through Water
STARTING AND OPERATING 285 DRIVING THROUGH WATER Shallow Standing Water Driving through water more than a few inches/ Although your vehicle is capable of driving through millimeters deep will require extra caution to ensure shallow standing water, consider the following Caution safety and prevent damage to your vehicle.
Page 286 286 STARTING AND OPERATING CAUTION! WARNING! • Driving through standing water may cause dam- • Driving through standing water limits your vehi- age to your vehicle’s drivetrain components. Al- cle’s traction capabilities. Do not exceed 5 mph (8 ways inspect your vehicle’s fluids (i.e., engine oil, km/h) when driving through standing water.
Page 287: Tire Safety Information
STARTING AND OPERATING 287 • European Metric tire sizing is based on European TIRE SAFETY INFORMATION design standards. Tires designed to this standard have Tire Markings the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation.
Page 288 288 STARTING AND OPERATING Tire Sizing Chart EXAMPLE: Size Designation: P = Passenger car tire size based on U.S. design standards ..blank..= Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Millimeters (mm)
Page 289 STARTING AND OPERATING 289 EXAMPLE: Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions (i.e., tire pressure, vehicle loading, road conditions,...
Page 290: Tire Identification Number (Tin)
290 STARTING AND OPERATING Tire Identification Number (TIN) located on the white sidewall side of the tire. Look for the TIN on the outboard side of black sidewall tires as mounted The TIN may be found on one or both sides of the tire, on the vehicle.
Page 291: Tire Loading And Tire Pressure
STARTING AND OPERATING 291 Tire and Loading Information Placard Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure is listed on either the face of the driver’s door or the driver’s side “B” pillar. Tire And Loading Information Placard This placard tells you important information about: 1) number of people that can be carried in the vehicle...
Page 292 292 STARTING AND OPERATING Loading combined weight of occupants, cargo/luggage and The vehicle maximum load on the tire must not exceed trailer tongue weight (if applicable) should never exceed the load carrying capacity of the tire on your vehicle. You the weight referenced here.
Page 293 STARTING AND OPERATING 293 5. Determine the combined weight of luggage and cargo NOTE: The following table shows examples on how to being loaded on the vehicle. That weight may not safely calculate total load, cargo/luggage, and towing capaci- exceed the available cargo and luggage load capacity ties of your vehicle with varying seating configurations calculated in Step 4.
Page 294 294 STARTING AND OPERATING...
Page 295: Tires - General Information
STARTING AND OPERATING 295 1. Safety— WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause accidents. recommended load capacity for your vehicle.
Page 296: Tire Inflation Pressures
296 STARTING AND OPERATING 2. Economy— maximum loaded vehicle condition. These pressure con- Improper inflation pressures can cause uneven wear ditions will be found in the “Supplemental Tire Pressure patterns to develop across the tire tread. These abnormal Information” section of this manual. wear patterns will reduce tread life resulting in a need for earlier tire replacement.
Page 297 STARTING AND OPERATING 297 check tire pressure. Do not make a visual judgement Check tire pressures more often if subject to a wide range when determining proper inflation. Radial tires may look of outdoor temperatures, as tire pressures vary with properly inflated even when they are under inflated.
Page 298: Radial-Ply Tires
298 STARTING AND OPERATING Tire Pressures for High Speed Operation Radial-Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
Page 299: Compact Spare Tire - If Equipped
STARTING AND OPERATING 299 Compact Spare Tire — If Equipped CAUTION! The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style Prolonged use of limited use spare, or an incorrect vehicle only.
Page 300: Limited Use Spare - If Equipped
300 STARTING AND OPERATING CAUTION! WARNING! Because of the reduced ground clearance, do not take The limited use spare tires are for emergency use your vehicle through an automatic car wash with the only. Installation of this limited use spare tire affects compact spare installed.
Page 301: Tire Spinning
STARTING AND OPERATING 301 WARNING! WARNING! Prolonged use of limited use spare, or incorrect tire Fast spinning tires can be dangerous. Forces gener- size of front wheel, may damage the transaxle differ- ated by excessive wheel speeds may cause tire dam- ential and result in loss of vehicle mobility and could age or failure.
Page 302: Tread Wear Indicators
302 STARTING AND OPERATING Tread Wear Indicators These indicators are molded into the bottom of the tread Tread wear indicators are in the original equipment tires grooves. They will appear as bands when the tread depth to help you in determining when your tires should be becomes 1/16 inch (2 mm).
Page 303: Replacement Tires
STARTING AND OPERATING 303 Replacement Tires WARNING! The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for Tires and spare tire should be replaced after six years, wear and correct cold tire inflation pressure. The manu- regardless of the remaining tread.
Page 304: Alignment And Balance
304 STARTING AND OPERATING WARNING! CAUTION! • Do not use a tire, wheel size or rating other than that Replacing original tires with tires of a different size specified for your vehicle. Some combinations of may result in false speedometer and odometer unapproved tires and wheels may change suspen- readings.
Page 305: Tire Chains
STARTING AND OPERATING 305 Improper alignment will not cause vehicle vibration. SNOW TIRES Vibration may be a result of tire and wheel out-of- Some areas of the country require the use of snow tires balance. Proper balancing will reduce vibration and during winter.
Page 306: Tire Rotation Recommendations
306 STARTING AND OPERATING TIRE ROTATION RECOMMENDATIONS The suggested rotation method is the “forward-cross” Tires on the front and rear axles of vehicles operate at shown in the following diagram. different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and tend to develop irregular wear pat- terns.
Page 307 STARTING AND OPERATING 307 • The tire pressure will vary with temperature by about • The TPM System will warn the driver of a low tire 1 psi (7 kPa) for every 12°F (7°C). This means that pressure if the tire pressure falls below the low- when the outside temperature decreases, the tire pres- pressure warning limit for any reason, including low sure will decrease.
Page 308 308 STARTING AND OPERATING − For example, your vehicle may have a recom- CAUTION! mended cold (parked for more than 3 hours) placard pressure of 30 psi (207 kPa). If the ambient tempera- • The TPMS has been optimized for the original ture is 68°F (20°C) and the measured tire pressure is equipment tires and wheels.
Page 309: Base System - If Equipped
STARTING AND OPERATING 309 • Seasonal temperature changes will affect tire pressure, NOTE: • The TPMS is not intended to replace normal tire care and the TPMS will monitor the actual tire pressure in and maintenance, or to provide warning of a tire the tire.
Page 310 310 STARTING AND OPERATING Tire Pressure Monitoring Low Pressure Warnings repeat, providing the system fault still exists. The Tire The Tire Pressure Monitoring Telltale Light will Pressure Monitoring Telltale Light will turn off when the illuminate in the instrument cluster and a chime fault condition no longer exists.
Page 311: Premium System - If Equipped
STARTING AND OPERATING 311 NOTE: 5. Once you repair or replace the original road tire, and 1. The compact spare tire (if so equipped) does not have reinstall it on the vehicle in place of the compact spare, a tire pressure monitoring sensor. Therefore, the TPMS the TPMS will update automatically and the TPM Telltale will not monitor the pressure in the compact spare tire.
Page 312 312 STARTING AND OPERATING The TPMS consists of the following components: Electronic Vehicle Information Center (EVIC) will display a graphic showing the pressure values of each tire with • Receiver Module the low tire pressure values flashing. • 4 Tire Pressure Monitoring Sensors •...
Page 313 STARTING AND OPERATING 313 updated tire pressures, the system will automatically update, the graphic display in the EVIC will stop flash- ing, and the Tire Pressure Monitoring Telltale Light will turn off. The vehicle may need to be driven for up to 10 minutes above 15 mph (25 km/h) in order for the TPMS to receive this information.
Page 314 314 STARTING AND OPERATING 1. Jamming due to electronic devices or driving next to Light will remain ON, a chime will sound, and the EVIC facilities emitting the same Radio Frequencies as the TPM will still display a flashing pressure value in the graphic sensors.
Page 315: General Information
STARTING AND OPERATING 315 TPM Telltale Light will turn OFF and the graphic in the The tire pressure sensors are covered under one of the EVIC will display a new pressure value instead of dashes following licenses: (- -), as long no tire pressure is below the low-pressure warning limit in any of the four active road tires.
Page 316: 3.5L Engine
316 STARTING AND OPERATING 3.5L Engine Poor quality gasoline can cause problems such as hard The 3.5L engine is designed to meet all starting, stalling, and hesitations. If you experience these emissions regulations and provide satisfac- symptoms, try another brand of gasoline (with the ap- tory fuel economy and performance when propriate octane rating for your engine) before consider- using high-quality unleaded gasoline hav-...
Page 317: Gasoline/Oxygenate Blends
STARTING AND OPERATING 317 Reformulated gasolines contain oxygenates, and are spe- CAUTION! cifically blended to reduce vehicle emissions and im- prove air quality. For vehicles equipped with a 2.4L or 3.5L engine, DO NOT use gasoline containing Methanol or E85 Etha- The manufacturer supports the use of reformulated gaso- nol.
Page 318: Mmt In Gasoline
318 STARTING AND OPERATING MMT In Gasoline Materials Added to Fuel MMT is a manganese containing metallic additive that is All gasoline sold in the United States is required to blended into some gasoline to increase octane. Gasoline contain effective detergent additives. Use of additional blended with MMT provides no performance advantage detergents or other additives is not needed under normal beyond gasoline of the same octane number without...
Page 319: Starting And Operating 319
STARTING AND OPERATING 319 • An out-of-tune engine, or certain fuel or ignition Carbon Monoxide Warnings malfunctions, can cause the catalytic converter to WARNING! overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or Carbon monoxide (CO) in exhaust gases is deadly.
Page 320: Flexible Fuel- 2.7L Engines Only (Except California Emission States)
320 STARTING AND OPERATING • Guard against carbon monoxide with proper mainte- nance. Have the exhaust system inspected every time the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. • Keep the trunk closed when driving your vehicle to prevent carbon monoxide and other poisonous ex- haust gases from entering the vehicle.
Page 321: Ethanol Fuel (E-85)
STARTING AND OPERATING 321 WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 322: Selection Of Engine Oil For Flexible Fuel Vehicles (E-85) And Gasoline Vehicles
322 STARTING AND OPERATING For best results, a refueling pattern that alternates be- Selection Of Engine Oil For Flexible Fuel Vehicles tween E-85 and unleaded gasoline should be avoided. (E-85) and Gasoline Vehicles When you do switch fuels, it is recommended that: FFV vehicles operated on E85 require specially formu- lated engine oils.
Page 323: Starting
STARTING AND OPERATING 323 Starting CAUTION! The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0° F (-18° C). In Replacing fuel system components with non-ethanol the range of 0° F (-18° C) to 32° F (0° C), you may compatible components can damage your vehicle.
Page 324: Adding Fuel
324 STARTING AND OPERATING ADDING FUEL Fuel Filler Cap (Gas Cap) As a reminder, a fuel icon with an arrow indicating which side of the vehicle the fuel filler door is located on, is located in the instrument cluster, just below the Fuel Gage. The gas cap is behind the fuel filler door, on the left rear quarter panel of the vehicle.
Page 325 STARTING AND OPERATING 325 CAUTION! • Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). • A poorly fitting gas cap could let impurities into the fuel system. •...
Page 326: Loose Fuel Filler Cap Message
326 STARTING AND OPERATING NOTE: WARNING! • Tighten the gas cap until you hear a “clicking” sound. This is an indication that the gas cap is tightened • Never have any smoking materials lit in or near properly. The Malfunction Indicator Light in the in- the vehicle when the gas cap is removed or the strument cluster may turn on if the gas cap is not tank filled.
Page 327: Vehicle Loading
STARTING AND OPERATING 327 vehicle is started. This might indicate a damaged cap. If Vehicle Curb Weight the problem is detected twice in a row, the system will 2.4 L SE ..... 3355 lbs (1522 kg) turn on the Malfunction Indicator Light (MIL).
Page 328: Gross Vehicle Weight Rating (Gvwr)
328 STARTING AND OPERATING • Gross Axle Weight Rating (GAWR) rear WARNING! • Vehicle Identification Number (VIN) Because the front wheels steer the vehicle, it is • Type of Vehicle important that you do not exceed the maximum front • Month Day and Hour of Manufacture (MDH) or rear GAWR.
Page 329: Loading
STARTING AND OPERATING 329 Figure out the weight on the front and rear of the vehicle A loaded vehicle is shown in the illustration. Note that separately. It is important that you distribute the load neither the GVWR nor the GAWR capacities have been evenly over the front and rear axles.
Page 330: Trailer Towing
330 STARTING AND OPERATING TRAILER TOWING Gross Vehicle Weight Rating (GVWR) In this section, you will find safety tips and information The GVWR is the total allowable weight of your vehicle. on limits to the type of towing you can reasonably do This includes driver, passengers, cargo, and tongue with your vehicle.
Page 331 STARTING AND OPERATING 331 Gross Combination Weight Rating (GCWR) Tongue Weight (TW) The gross combination weight rating (GCWR) is the total Tongue Weight (TW) is the downward force exerted on permissible weight of your vehicle and trailer when the hitch ball by the trailer. In most cases it should not be weighed in combination.
Page 332: Trailer Hitch Classification
332 STARTING AND OPERATING Trailer Hitch Classification Trailer Towing Weights (Maximum Trailer Weight The following chart provides the industry standard for Ratings) the maximum trailer weight a given trailer hitch class can The following chart provides the maximum trailer tow and should be used to assist you in selecting the weight ratings towable for your given drivetrain.
Page 333: Trailer And Tongue Weight
STARTING AND OPERATING 333 Engine/Transaxle Max. Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. 2.4L/Auto See Note 1000 lbs (450 kg) 100 lbs (45 kg) 2.7L/Auto See Note 1500 lbs (680 kg) 150 lbs (68 kg) 3.5L/Auto 22 Sq., Ft. (2.0 Sq. M) 2000 lbs (900 kg) 200 lbs (90 kg) Refer to local laws for maximum trailer towing speeds.
Page 334 334 STARTING AND OPERATING the trailer to sway severely side to side which will cause Consider the following items when computing the loss of control of vehicle and trailer. Failure to load weight on the rear axle of the vehicle: trailers heavier in front is the cause of many trailer •...
Page 335: Towing Requirements
STARTING AND OPERATING 335 CAUTION! CAUTION! • Avoid towing a trailer for the first 500 miles (805 Incorrect tongue weight could result in increased yaw or vehicle instability. A negative tongue weight km) of vehicle operation. Doing so may damage could unload the rear suspension of the tow vehicle your vehicle.
Page 336 336 STARTING AND OPERATING • Safety chains must always be used between your WARNING! vehicle and trailer. Always connect the chains to the frame or hook retainers of the vehicle hitch. Cross the Improper towing can lead to an injury accident. chains under the trailer tongue and allow enough Follow these guidelines to make your trailer towing slack for turning corners.
Page 337 STARTING AND OPERATING 337 4. Tongue weight rating for the trailer hitch utilized Information” in this section for information on tread (This requirement may limit the ability to always wear indicators and for proper inspection procedure. achieve 10% of tongue weight as a percentage of total −...
Page 338 338 STARTING AND OPERATING − Trailer brakes are recommended for trailers over 1,000 WARNING! lbs (450 kg) and required for trailers in excess of 2,000 lbs (907 kg). Do not connect trailer brakes to your vehicle’s hy- draulic brake lines. It can overload your brake sys- CAUTION! tem and cause it to fail.
Page 339: Towing Tips
STARTING AND OPERATING 339 NOTE: Do not cut or splice wiring into the vehicles wiring harness. The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Seven-Pin Connector Towing Tips Before setting out on a trip, practice turning, stopping, and backing the trailer in an area located away from heavy traffic.
Page 340 340 STARTING AND OPERATING Towing Tips — Automatic Transaxle sealed and the fluid level cannot be checked. See your The “D” range can be selected when towing. However, if authorized dealership service center for assistance. frequent shifting occurs while in this range, the “3” range Towing Tips —...
Page 341: Recreational Towing (Behind Motorhome, Etc.)
STARTING AND OPERATING 341 − Highway Driving RECREATIONAL TOWING (BEHIND Reduce speed. MOTORHOME, ETC.) − Air Conditioning Towing This Vehicle Behind Another Vehicle (Flat Turn off temporarily. towing with all four wheels on the ground) − Refer to Cooling System Operating information in the CAUTION! Maintenance section of this manual for more informa- tion.
Page 343: What To Do In Emergencies
WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Flasher ....345 Jump-Starting Procedures Due To A Low Battery ......354 If Your Engine Overheats .
Page 344 344 WHAT TO DO IN EMERGENCIES Towing This Vehicle Behind Another Vehicle Without Power — Override Transaxle Interlock With A Tow Dolly ..... 360 System .
Page 345: Hazard Warning Flasher
WHAT TO DO IN EMERGENCIES 345 Do not use this emergency warning system when the HAZARD WARNING FLASHER The flasher switch is located on the instrument panel, vehicle is in motion. Use it when your vehicle is disabled below the radio. Depress the switch and both cluster and it is creating a safety hazard for other motorists.
Page 346 346 WHAT TO DO IN EMERGENCIES If the pointer rises to the H (red) mark, the instrument CAUTION! cluster will sound a chime. Pull over and stop the vehicle with the engine at idle, when safe. Turn off the air Driving with a hot cooling system could damage conditioning and wait until the pointer drops back into your vehicle.
Page 347: Engine Oil Overheating - 2.4L Engine Only (If Equipped)
WHAT TO DO IN EMERGENCIES 347 Engine Oil Overheating — 2.4L Engine Only (If WARNING! Equipped) During sustained high-speed driving or trailer tow up A hot engine cooling system is dangerous. You or long grades on a hot day, the engine oil temperature may others could be badly burned by steam or boiling become too hot.
Page 348: Jacking And Tire Changing
348 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING Jack Location The jack and jack-handle are stowed under the load floor WARNING! in the trunk. Spare Tire Stowage • Being under a jacked-up vehicle is dangerous. The The compact spare tire is stowed under the rear load floor vehicle could slip off the jack and fall on you.
Page 349: Preparations For Jacking
WHAT TO DO IN EMERGENCIES 349 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. •...
Page 350: Jacking Instructions
350 WHAT TO DO IN EMERGENCIES Jacking Instructions 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench, and remove the wrench from the jack assembly.
Page 351 WHAT TO DO IN EMERGENCIES 351 Jacking Locations...
Page 352 352 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! Do not attempt to raise the vehicle by jacking on Raising the vehicle higher than necessary can make locations other than those indicated in step 3. the vehicle less stable. It could slip off the jack and hurt someone near it.
Page 353 WHAT TO DO IN EMERGENCIES 353 WARNING! WARNING! To avoid possible personal injury, handle the wheel A loose tire or jack thrown forward in a collision or covers with care to avoid contact with any sharp hard stop could endanger the occupants of the ve- edges.
Page 354: Jump-Starting Procedures Due To A Low Battery
354 WHAT TO DO IN EMERGENCIES JUMP-STARTING PROCEDURES DUE TO A LOW WARNING! BATTERY Jump-starting remote battery terminals are located under • Take care to avoid the radiator cooling fan when- the hood. ever the hood is raised. It can start anytime the ignition switch is on.
Page 355 WHAT TO DO IN EMERGENCIES 355 1. Wear eye protection and remove any metal jewelry 3. Turn off the heater, radio, and all unnecessary electri- such as watchbands or bracelets that might make an cal loads. inadvertent electrical contact. 4. Remove the protective cover over the remote jump- 2.
Page 356 356 WHAT TO DO IN EMERGENCIES 7. Start the engine in the vehicle that has the booster battery, let the engine idle a few minutes, and then start the engine in the vehicle with the discharged battery. 8. When removing the jumper cables, reverse the se- quence exactly.
Page 357: Freeing A Stuck Vehicle
WHAT TO DO IN EMERGENCIES 357 NOTE: Refer to “Maintenance Procedures” in Section 7 FREEING A STUCK VEHICLE of this manual for information on accessing the battery If your vehicle becomes stuck in mud, sand, or snow, it for service or replacement. can often be moved by a rocking motion.
Page 358 358 WHAT TO DO IN EMERGENCIES WARNING! CAUTION! Fast spinning tires can be dangerous. Forces gener- Racing the engine or spinning the wheels too fast ated by excessive wheel speeds may cause axle and may lead to transaxle overheating and failure. It can tire damage or failure.
Page 359: Towing A Disabled Vehicle
WHAT TO DO IN EMERGENCIES 359 TOWING A DISABLED VEHICLE CAUTION! With The Ignition Key • If the vehicle being towed requires steering, the Front Wheel Drive ignition switch must be in the ON position, not in Your vehicle may be towed (with all 4 wheels flat on the the LOCK or ACC position.
Page 360: Without The Ignition Key
360 WHAT TO DO IN EMERGENCIES WITHOUT THE IGNITION KEY TOWING THIS VEHICLE BEHIND ANOTHER Special care must be taken when the vehicle is towed VEHICLE WITH A TOW DOLLY with the ignition in the LOCK position. Flat bed towing Rear towing is not recommended with the front wheels is the preferred towing method.
Page 361 WHAT TO DO IN EMERGENCIES 361 • Insert a key, screwdriver, or finger into the front hole Battery power is required to release the brake/transaxle interlock system. There is an override system that allows then push and hold the manual override release lever you to shift out of PARK in case of loss of power.
Page 363: Maintaining Your Vehicle
MAINTAINING YOUR VEHICLE CONTENTS 2.4L Gas Engine Compartment ... . . 366 Maintenance Procedures ....373 2.7L Gas Engine Compartment .
Page 364 364 MAINTAINING YOUR VEHICLE A/C Air Filter — If Equipped ... . 382 Front And Rear Wheel Bearings ... 398 Power Steering —...
Page 365 MAINTAINING YOUR VEHICLE 365 Center High-Mounted Stop Light ..417 Fluids, Lubricants, And Genuine Parts ..419 Fluids And Capacities ....418 Engine .
Page 366: 2.4L Gas Engine Compartment
366 MAINTAINING YOUR VEHICLE 2.4L GAS ENGINE COMPARTMENT...
Page 367: L Gas Engine Compartment
MAINTAINING YOUR VEHICLE 367 2.7L GAS ENGINE COMPARTMENT...
Page 368: 3.5L Engine Compartment
368 MAINTAINING YOUR VEHICLE 3.5L ENGINE COMPARTMENT 3.5L Engine...
Page 369: Onboard Diagnostic System - Obd Ii
MAINTAINING YOUR VEHICLE 369 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors • Prolonged driving with the “Malfunction Indica- the performance of the emissions, engine, and automatic tor Light”...
Page 370: Loose Fuel Filler Cap Message
370 MAINTAINING YOUR VEHICLE Loose Fuel Filler Cap Message EMISSIONS INSPECTION AND MAINTENANCE After fuel is added, the vehicle diagnostic system can PROGRAMS determine if the fuel filler cap is possibly loose or In some localities, it may be a legal requirement to pass improperly installed.
Page 371 MAINTAINING YOUR VEHICLE 371 Your vehicle has a simple ignition key-actuated test, a. The MIL will flash for about 10 seconds and then which you can use prior to going to the test station. To return to being fully illuminated until you turn OFF check if your vehicle’s OBD system is ready, you must do the ignition key or start the engine.
Page 372: Replacement Parts
372 MAINTAINING YOUR VEHICLE Regardless of whether your vehicle’s OBD system is AUTHORIZED DEALER SERVICE ready or not ready, if the MIL symbol is illuminated Your authorized dealer has the qualified service person- during normal vehicle operation, you should have your nel, special tools, and equipment to perform all service vehicle serviced before going to the I/M station.
Page 373: Maintenance Procedures
MAINTAINING YOUR VEHICLE 373 The best time to check the engine oil level is about 5 MAINTENANCE PROCEDURES The pages that follow contain the required maintenance minutes after a fully warmed engine is shut off. Do not services determined by the engineers who designed your check oil level before starting the engine after it has sat vehicle.
Page 374 374 MAINTAINING YOUR VEHICLE CAUTION! Do not overfill the engine. Overfilling the engine will cause oil aeration, which can lead to loss of oil pressure and an increase in oil temperature. This could damage your engine. Change Engine Oil The oil change indicator system will remind you that it is time to take your vehicle in for scheduled maintenance.
Page 375 MAINTAINING YOUR VEHICLE 375 Engine Oil Selection Engine Oil Viscosity (SAE Grade) — 2.4L and 2.7L For best performance and maximum protection under all Engines types of operating conditions, the manufacturer recom- SAE 5W-20 engine oil is recommended for all operating mends engine oils that are API Certified and meet the temperatures.
Page 376: Engine Oil Filter
376 MAINTAINING YOUR VEHICLE Lubricants which do not have both, the engine oil certi- Materials Added To Engine Oils fication mark and the correct SAE viscosity grade num- The manufacture strongly recommends against the addi- ber should not be used. tion of any additives (other than leak detection dyes) to the engine oil.
Page 377: Drive Belt
MAINTAINING YOUR VEHICLE 377 Engine Oil Filter Selection Spark Plugs All of this manufacturer’s engines have a full-flow type Spark plugs must fire properly to assure engine perfor- disposable oil filter. Use a filter of this type for replace- mance and emission control. New plugs should be in- ment.
Page 378: Catalytic Converter
378 MAINTAINING YOUR VEHICLE Under normal operating conditions, the catalytic con- WARNING! verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure The air induction system (air cleaner, hoses, etc) can proper catalyst operation and prevent possible catalyst provide a measure of protection in the case of engine damage.
Page 379: Maintenance-Free Battery
MAINTAINING YOUR VEHICLE 379 NOTE: Intentional tampering with emissions control To minimize the possibility of catalyst damage: systems can result in civil penalties being assessed • Do not shut off the engine or interrupt the ignition against you. when the transaxle is in gear and the vehicle is in motion.
Page 380 380 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Battery fluid is a corrosive acid solution and can • It is essential when replacing the cables on the burn or even blind you. Don’t allow battery fluid battery that the positive cable is attached to the to contact your eyes, skin, or clothing.
Page 381: Air Conditioner Maintenance
MAINTAINING YOUR VEHICLE 381 Air Conditioner Maintenance WARNING! For best possible performance, your air conditioner should be checked and serviced by an Authorized Dealer • Use only refrigerants and compressor lubricants at the start of each warm season. This service should approved by the manufacturer for your air condi- include cleaning of the condenser fins and a performance tioning system.
Page 382: A/C Air Filter - If Equipped
382 MAINTAINING YOUR VEHICLE Refrigerant Recovery and Recycling The A/C Air Filter is located in the fresh air inlet behind R-134a Air Conditioning Refrigerant is a hydrofluorocar- the glove box. Perform the following procedure to re- bon (HFC) that is endorsed by the Environmental Pro- place the filter: tection Agency and is an ozone-saving product.
Page 383: Power Steering - Fluid Check
MAINTAINING YOUR VEHICLE 383 CAUTION! The A/C Air Filter is labeled with an arrow to indicate airflow direction through the filter. Failure to install the filter properly will result in the need to replace it more often. 8. Reinstall the glove box door dampener and glove box. Power Steering —...
Page 384: Front Suspension Ball Joints
384 MAINTAINING YOUR VEHICLE Steering Linkage WARNING! The tie rod end ball joints should be inspected for external leakage and damage when other maintenance is Fluid level should be checked on a level surface and performed. with the engine off to prevent injury from moving parts and to insure accurate fluid level reading.
Page 385: Windshield Wiper Blades
MAINTAINING YOUR VEHICLE 385 amount of a high quality lubricant such as Mopar Lock Keep the blade rubber out of contact with petroleum Cylinder Lubricant or equivalent directly into the lock products such as engine oil, gasoline, etc. cylinder. NOTE: Always refer to the wiper blade packaging for specific installation instructions.
Page 386: Exhaust System
386 MAINTAINING YOUR VEHICLE If you notice a change in the sound of the exhaust system, WARNING! or if exhaust fumes can be detected inside the vehicle, or when the underside or rear of the vehicle is damaged; Commercially available windshield washer solvents have a competent technician inspect the complete ex- are flammable.
Page 387: Cooling System
MAINTAINING YOUR VEHICLE 387 Coolant Checks Cooling System Check engine coolant (antifreeze) protection every 12 WARNING! months (before the onset of freezing weather, where applicable). If coolant is dirty or rusty in appearance, the • When working near the radiator cooling fan, dis- system should be drained, flushed, and refilled with connect the fan motor lead or turn the ignition fresh coolant.
Page 388 388 MAINTAINING YOUR VEHICLE If the solution is dirty or contains a considerable amount CAUTION! of sediment, clean and flush with a reliable cooling system cleaner. Follow with a thorough rinsing to remove • Mixing of coolants other than specified HOAT all deposits and chemicals.
Page 389 MAINTAINING YOUR VEHICLE 389 • Use only high purity water such as distilled or deion- Adding Coolant Your vehicle has been built with an improved engine ized water when mixing the water/engine coolant coolant that allows extended maintenance intervals. This solution.
Page 390 390 MAINTAINING YOUR VEHICLE The cap should be inspected and cleaned if there is any Disposal of Used Engine Coolant accumulation of foreign material on the sealing surfaces. Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your WARNING! local authorities to determine the disposal rules for your community.
Page 391 MAINTAINING YOUR VEHICLE 391 6 Cylinder Engines — the level of the coolant in the humidity accumulating on the radiator and being vapor- pressurized coolant bottle should be between the ized when the thermostat opens, allowing hot coolant to “COLD” and “FULL” range on the bottle when the enter the radiator.
Page 392: Hoses And Vacuum/Vapor Harnesses
392 MAINTAINING YOUR VEHICLE • Maintain coolant concentration at 50% HOAT engine Hoses and Vacuum/Vapor Harnesses coolant (minimum) and distilled water for proper Inspect surfaces of hoses and nylon tubing for evidence corrosion protection of your engine, which contains of heat and mechanical damage. Hard or soft spots, aluminum components.
Page 393: Fuel System
MAINTAINING YOUR VEHICLE 393 Fuel System WARNING! Electronic Fuel Injection high-pressure fuel systems are designed with tubes and special connects, connections, Riding the brakes can lead to brake failure and and clamps which have unique material characteristics to possibly an accident. Driving with your foot resting provide adequate sealing and resist attack by deterio- or riding on the brake pedal can result in abnormally rated gasoline.
Page 394 394 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or immediately! Eventual deterioration of the hose can collapsed. take place resulting in a possibility of a burst failure. Inspect all hose clamps and couplings to make sure they WARNING! are secure and no leaks are present.
Page 395 MAINTAINING YOUR VEHICLE 395 Clean the top of the master cylinder area before removing WARNING! the cap. If necessary, add fluid to bring the fluid level up to the requirements described on the brake fluid reser- • Overfilling the brake fluid reservoir can result in voir.
Page 396: Automatic Transaxle
396 MAINTAINING YOUR VEHICLE Fluid Level Check — Vehicles with 2.4L and 2.7L CAUTION! Engines Use the following procedure to check the automatic Do not allow petroleum base fluid to contaminate the transaxle fluid level properly: brake fluid, all brake seal components could be damaged causing partial or complete brake failure.
Page 397 MAINTAINING YOUR VEHICLE 397 driven at least 15 miles (24 km). Hot fluid cannot be held CAUTION! comfortably between the fingertips. Cold fluid is at a temperature below 80°F (27°C). • Using a transmission fluid other than the manu- facturer’s recommended fluid may cause deterio- 7.
Page 398: Front And Rear Wheel Bearings
398 MAINTAINING YOUR VEHICLE Fluid and Filter Changes Front and Rear Wheel Bearings Change the automatic transaxle fluid and filter at the Front and rear wheel bearings are permanently sealed. intervals shown in the “Maintenance Schedule” in this No regular maintenance is required for these compo- manual.
Page 399 MAINTAINING YOUR VEHICLE 399 The following maintenance recommendations will enable Washing you to obtain maximum benefit from the corrosion • Wash your vehicle regularly. Always wash your ve- resistance built into your vehicle. hicle in the shade using Mopar Car Wash or a mild car wash soap, and rinse the panels completely with What Causes Corrosion? Corrosion is the result of deterioration or removal of...
Page 400 400 MAINTAINING YOUR VEHICLE • If your vehicle is damaged due to an accident or CAUTION! similar cause, which destroys the paint and protective coating, have your vehicle repaired as soon as pos- Do not use abrasive or strong cleaning materials such sible.
Page 401 MAINTAINING YOUR VEHICLE 401 heavy soil and/or excessive brake dust, use Mopar Mopar Spot & Stain Remover if absolutely necessary. Do Wheel Cleaner (05066247AB) or equivalent or select a not use harsh cleaners or Armorall. Use Mopar Total nonabrasive, non-acidic cleaner. Do not use scouring Clean to clean vinyl upholstery pads, steel wool, a bristle brush, or metal polishes.
Page 402 402 MAINTAINING YOUR VEHICLE • For grease stains, apply Mopar Multi-Purpose WARNING! Cleaner to a clean, damp cloth and remove stain. Use a fresh, damp towel to remove soap residue. Do not use volatile solvents for cleaning purposes. • Do not use any solvents or protectants on Yes Essen- Many are potentially flammable, and if used in closed areas they may cause respiratory harm.
Page 403 MAINTAINING YOUR VEHICLE 403 Glass Surfaces 1. Clean with a wet soft rag. A mild soap solution may be All glass surfaces should be cleaned on a regular basis used, but do not use high alcohol content or abrasive with Mopar Glass Cleaner or any commercial cleaners.
Page 404: Cleaning The Center Console Cup Holders
404 MAINTAINING YOUR VEHICLE Cleaning The Center Console Cup Holders FUSES/TOTALLY INTEGRATED POWER MODULE (TIPM) Removal A Totally Integrated Power Module is located in the Grab the rubber portion of the cup holder and lift engine compartment near the air cleaner assembly. This upward.
Page 405 MAINTAINING YOUR VEHICLE 405 Cartridge Mini Cavity Description Fuse Fuse 40 Amp — — Green 20 Amp — — Yellow Battery Feed — Cen- 10 Amp ter High Mounted — Stop Light (CHMSL)/ Brake Switch 10 Amp Battery Feed — Igni- —...
Page 406 406 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse 30 Amp Ignition Off Draw 20 Amp — — — Green (IOD) Sense 1 Yellow 30 Amp Ignition Off Draw Ignition Off Draw — Green (IOD) Sense 2 (IOD) —...
Page 407 MAINTAINING YOUR VEHICLE 407 Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Off Draw Ignition Run — Cli- (IOD) — Wireless 10 Amp mate Controls/Hot — 10 Amp Control Module Cup Holder - if — (WCM)/Clock/ equipped Steering Control...
Page 408 408 MAINTAINING YOUR VEHICLE Cartridge Mini Cartridge Mini Cavity Description Cavity Description Fuse Fuse Fuse Fuse Ignition Run — Occu- 30 Amp Auto Shutdown — pant Classification Pink (ASD) Relay Feed 1 10 Amp — Module (OCM)/ Battery Feed — Occupant Restraint Switch Bank/ Controller (ORC)
Page 409 MAINTAINING YOUR VEHICLE 409 Cartridge Mini CAUTION! Cavity Description Fuse Fuse • When installing the Totally Integrated Power Battery Feed — Anti- Lock Brakes (ABS) Module cover, it is important to ensure the cover is Module - If properly positioned and fully latched. Failure to 40 Amp —...
Page 410: Vehicle Storage
410 MAINTAINING YOUR VEHICLE VEHICLE STORAGE LIGHT BULBS — Interior Bulb Number If you will not be using your vehicle for more than 21 Front Courtesy/Reading Lights ..578/W5W days you may want to take steps to preserve your battery. Center Courtesy/Reading Lights .
Page 411: Bulb Replacement
MAINTAINING YOUR VEHICLE 411 BULB REPLACEMENT LIGHTS BULBS — Outside Bulb No. Low Beam Headlight ..... 9006 Headlight Bulb Replacement High Beam Headlight.
Page 412 412 MAINTAINING YOUR VEHICLE 2. Reach into engine compartment and from behind the lamp assembly and grasp the connector. Twisting Bulb From Socket CAUTION! Headlight Housing - Rear View 3. Rotate bulb and connector ⁄ turn and pull outward Do not touch the new bulb with your fingers. Oil from assembly.
Page 413: Fog Lights
MAINTAINING YOUR VEHICLE 413 4. Pull the bulb out of the socket and replace the bulb. Fog Lights 1. Access to the lights through the lower fascia cutout is limited. 2. We recommend you access the lights by turning the steering wheel to allow access and remove the inner fender shield.
Page 414: Taillights, Rear Turn Signals And Backup Lights - Replacement
414 MAINTAINING YOUR VEHICLE 3. Rotate bulb and connector ⁄ turn counterclockwise. Taillights, Rear Turn Signals And Backup Lights — Replacement 4. Pull bulb off of connector and replace with a new one. The turn signal, brake and taillights and backup lights are located in the rear corner body panel housing.
Page 415 MAINTAINING YOUR VEHICLE 415 Changing the Rear Corner Taillight Bulbs 1. Open the trunk and gently pull back the trunk liner behind the taillight. Location Plastic Wing Nuts 3. Grasp the taillight and pull firmly outward pushing gently on the studs from inside to disengage the light housing.
Page 416: License Plate Light - Rear
416 MAINTAINING YOUR VEHICLE 5. Remove bulb from socket and replace. License Plate Light — Rear 1. Remove two retaining screws holding the light lens in place. Changing Tail Light Bulb Location and Removal of Rear License Light Assembly 2. Gently pry the light assembly loose.
Page 417 MAINTAINING YOUR VEHICLE 417 3. Pull bulb from socket, replace and reattach the light 2. Twist and remove socket from the back of the light assembly with the two retaining screws. housing. Center High-Mounted Stop Light 1. Open the trunk lid to find the centrally located high- mounted stop light.
Page 418 418 MAINTAINING YOUR VEHICLE FLUIDS AND CAPACITIES Engine U.S. Metric Fuel (approximate) All FWD Engines — (Except 2.4L PZEV) 16.9 gallons 64 liters 3.5L Engine with AWD (All Wheel Drive) 17.3 gallons 65.5 liters 2.4L PZEV (Partial Zero Emissions Vehicle) 18.4 gallons 69.7 liters Engine Oil with Filter...
Page 419 MAINTAINING YOUR VEHICLE 419 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluids, Lubricants, and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Engine Coolant Organic Additive Technology) or equivalent Use API Certified engine oil. SAE 5W-20 is recommended. Refer to the en- Engine Oil (2.4L &...
Page 420 420 MAINTAINING YOUR VEHICLE Component Fluids, Lubricants, and Genuine Parts Fuel Selection (2.7L - EXCEPT CALI- E-85 Ethanol FORNIA EMISSION STATES) Fuel Selection (3.5L) 87 to 89 Octane Chassis Component Fluids, Lubricants and Genuine Parts Automatic Transaxle Mopar ATF+4 Automatic Transmission Fluid. Mopar DOT 3 and SAE J1703 should be used.
Page 421 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..422 Required Maintenance Intervals ... 425 Maintenance Schedule ....422...
Page 422 422 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE MAINTENANCE SCHEDULE The “Scheduled” maintenance services, listed in bold The oil change indicator system will remind you that it is type must be done at the times or mileages specified to time to take your vehicle in for scheduled maintenance. assure the continued proper functioning of the emission On Electronic Vehicle Information Center (EVIC) control system.
Page 423 MAINTENANCE SCHEDULES 423 NOTE: this manual or under “Odometer/Trip Odometer” under • The oil change indicator message will not monitor the “Instrument Cluster Descriptions” in Section 3 of this time since the last oil change. Change your vehicles oil manual. if it has been 6 months since your last oil change even At Each Stop for Fuel if the oil change indicator message is NOT illumi-...
Page 424 424 MAINTENANCE SCHEDULES • Check the fluid levels of coolant reservoir, brake At Each Oil Change master cylinder, power steering, and automatic trans- • Change the engine oil filter. axle, and add fluid as needed. • Inspect the brake hoses and lines. NOTE: Six speed AutoStick Transaxle —...
Page 425 MAINTENANCE SCHEDULES 425 Required Maintenance Intervals Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Change the engine oil and engine oil filter. 6,000 10 000 Rotate the tires. 6,000 10 000 If using your vehicle in dusty or off-road conditions,...
Page 426 426 MAINTENANCE SCHEDULES Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the spark plugs on 2.4L engines (except 30,000 50 000 PZEV* engine). Inspect and adjust the power steering pump belt ten- 30,000 50 000 sion on 2.4L engines.
Page 427 MAINTENANCE SCHEDULES 427 Perform Maintenance Every (Where time and mileage are listed, follow the interval that occurs first.) Maintenance Items Miles Kilometers or Months Replace the timing belt on 2.4L and 3.5L engines. 102,000 170 000 Change the automatic transaxle fluid & filter. 120,000 200 000 Replace the accessory drive belt on 2.7L engines.
Page 429 IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your In Mexico Contact ..... 432 Vehicle ......431 Customer Assistance For The Hearing Or Prepare For The Appointment .
Page 430 430 IF YOU NEED CONSUMER ASSISTANCE Publication Order Forms ....435 Traction Grades ..... . 437 Department Of Transportation Uniform Tire Temperature Grades .
Page 431: Suggestions For Obtaining Service For Your Vehicle
IF YOU NEED CONSUMER ASSISTANCE 431 SUGGESTIONS FOR OBTAINING SERVICE FOR Be Reasonable With Requests YOUR VEHICLE If you list a number of items, and you must have your vehicle by the end of the day, discuss the situation with Prepare For The Appointment the service advisor and list the items in order of priority.
Page 432: Daimlerchrysler Motors Corporation Customer Center
432 IF YOU NEED CONSUMER ASSISTANCE • Vehicle Identification Number (VIN) special tools, and the latest information to assure your vehicle is fixed correctly and in a timely manner. • Vehicle delivery date and mileage This is why you should always talk to your authorized DaimlerChrysler Motors Corporation Customer dealer’s service manager first.
Page 433 IF YOU NEED CONSUMER ASSISTANCE 433 contract, call the manufacturer’s Service Contract Na- Customer Assistance for the Hearing or Speech Impaired (TDD/TTY) tional Customer Hotline at 1-800-521-9922. To assist customers who have hearing difficulties, the The manufacturer will not stand behind any service manufacturer has installed special TDD (Telecommuni- contract that is not the manufacturer’s Service Contract.
Page 434 434 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS WARNING! Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your Engine exhaust, some of its constituents, and certain vehicle operating at its best. vehicle components contain, or emit, chemicals known to the State of California to cause cancer and REPORTING SAFETY DEFECTS birth defects or other reproductive harm.
Page 435: Publication Order Forms
IF YOU NEED CONSUMER ASSISTANCE 435 To contact NHTSA, you may either call the Auto Safety PUBLICATION ORDER FORMS Hotline toll free at 1–888–327–4236 (TTY: 1–800–424– To order the following manuals, you may use either the 9153), or go to http://www.safercar.gov; or write to: website or the phone numbers listed below.
Page 436 436 IF YOU NEED CONSUMER ASSISTANCE • Diagnostic Procedure Manuals Call toll free at: • 1–800–890–4038 (U.S.) Diagnostic Procedure Manuals are filled with dia- grams, charts and detailed illustrations. These practi- • 1–800–387–1143 (Canada) cal manuals make it easy for students and technicians to find and fix problems on computer-controlled ve- hicle systems and features.
Page 437: Traction Grades
IF YOU NEED CONSUMER ASSISTANCE 437 conditions of their use, however, and may depart signifi- DEPARTMENT OF TRANSPORTATION UNIFORM TIRE QUALITY GRADES cantly from the norm due to variations in driving habits, The following tire grading categories were established by service practices, and differences in road characteristics the National Highway Traffic Safety Administration.
Page 438 438 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 439 INDEX...
Page 440 440 INDEX ABS (Anti-Lock Brake System) ....275 Airbag, Window (Side Curtain) ... 56,60,61 Adding Engine Coolant (Antifreeze) ..389 Alarm System (Security Alarm) .
Page 441 INDEX 441 Automatic Door Locks ....32,33 Location ......379 Automatic Oil Change Indicator .
Page 442 442 INDEX Bulbs, Light ......410 Cellular Phone ....91,216,217,233 Center High Mounted Stop Light .
Page 443 INDEX 443 Compact Spare Tire ..... . 299 Drain, Flush, and Refill ....387 Compass .
Page 444 444 INDEX Digital Video Disc (DVD) Player ..212,216 E-85 Fuel ......320 Dimmer Switch, Headlight .
Page 445 INDEX 445 Cooling ......387 Exhaust Gas Caution ....79,319,386 Exhaust Gas Caution .
Page 446 446 INDEX Engine Oil ......322 Freeing A Stuck Vehicle ....357 Fuel Requirements .
Page 447 INDEX 447 Fuel System Caution ..... 325 Gross Axle Weight Rating ....328,331 Fueling .
Page 448 448 INDEX Heated Seats ......126 Instrument Panel and Controls ....171 Heater .
Page 449 INDEX 449 Keyless Entry System (Sedan) ....22 Daytime Running ..... . 135 Keys .
Page 450 450 INDEX Seat Belt Reminder ..... 175 Lubrication, Body ..... . . 384 Security Alarm (Theft Alarm) .
Page 451 INDEX 451 Modifications/Alterations, Vehicle ... . . 7 Capacity ......418 Monitor, Tire Pressure System .
Page 452 452 INDEX Overheating, Engine ..... . 345 Outlet (Auxiliary Electrical Outlet) ..156 Owner’s Manual (Operator Manual) .
Page 453 INDEX 453 Radio Operation ....213,217,233 Remote Keyless Entry (Sedan) ....22 Radio Remote Controls .
Page 454 454 INDEX Safety Tips ......79 Seats ....... . . 123 Satellite Radio .
Page 455 INDEX 455 Settings, Personal ......193 Steering Shoulder Belts ......42 Linkage .
Page 456 456 INDEX Temperature Gauge, Engine Coolant ..174,346 General Information ....295 Tether Anchor, Child Restraint ....72 High Speed .
Page 457 INDEX 457 24-Hour Towing Assistance ....104 Filter ....... 398 Disabled Vehicle .
Page 458 458 INDEX UCI Connector ......219 Vehicle Storage ..... . . 246,410 UConnect™...
Page 459 INDEX 459 Wheel Bearings ......398 Fluid ....... 385 Wind Buffeting .
Page 460 INTRODUCTION INTRODUCTION HOW TO USE THIS MANUAL WARNINGS AND CAUTIONS VEHICLE IDENTIFICATION NUMBER VEHICLE MODIFICATIONS/ALTERATIONS THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS IGNITION KEY REMOVALKEY-IN-IGNITION REMINDERLOCKING DOORS WITH THE KEYSENTRY KEY REPLACEMENT KEYSSENTRY KEY PROGRAMMINGGENERAL INFORMATIONSECURITY ALARM SYSTEM - IF EQUIPPED REARMING THE SYSTEMTO ARM THE SYSTEMTO DISARM THE SYSTEMILLUMINATED ENTRY SYSTEM - IF EQUIPPED REMOTE KEYLESS ENTRY - IF EQUIPPED TO UNLOCK THE DOORSTO LOCK THE DOORSTO UNLATCH THE TRUNKUSING THE EXPRESS DOWN WINDOWS FEATURE USING THE PANIC ALARMPROGRAMMING ADDITIONAL TRANSMITTERSBATTERY REPLACEMENTGENERAL INFORMATIONREMOTE START SYSTEM - IF EQUIPPED HOW TO USE REMOTE STARTDOOR LOCKS MANUAL DOOR LOCKSPOWER DOOR LOCKS CHILD-PROTECTION DOOR LOCK SYSTEM (REAR DOORS)POWER WINDOWS POWER WINDOW SWITCHESAUTO WINDOW DOWN - IF EQUIPPEDAUTO WINDOW UP - IF EQUIPPEDRESET AUTO UPWINDOW LOCKOUT SWITCHWIND BUFFETINGTRUNK...

Dodge Avenger Owner's Manual

Introduction 1

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

306 Starting and Operating

Starting and Operating

Quick Links

INTRODUCTION

Chapters

Related Manuals for Dodge Avenger

Summary of Contents for Dodge Avenger