Byron BY212 Installation And Operation Instruction

Plug-in & Portable
™
Wire Free Chime Kit
BY212
5: 8:
6: 6:
4:
7: 7:
1:
2:
:3
1: Push Button 5: Portable Chime
2: Melody Selector 6: Speaker
3: Bell Push Battery 7: Volume control
4: Signal Sent LED 8: Plug-in Chime
1
1: Place a small flat screwdriver
into the locking clip on the
base of the Bell Push
2: Gently twist
3: The backing plate will unclip
2 1: Insert CR2032 battery
(Supplied) into the battery
holder.
2: Make sure the positive side
is facing upwards.
3: Replace back plate.
Warning: Make sure that the batteries are
replaced correctly to avoid battery failure.
Only replace with same or equivalent type.
3
1: Remove the battery cover of
the Door Chime.
2: Insert 3 X 1.5V Size 'AA'
batteries (Not Supplied).
3: Make sure the
Positive/Negative terminals
match the internal markings.
4: Chime will 'Beep' on Start up.
5: Replace the battery cover
3 x 1.5V 'AA'
4
ON
ON
5
Functions:
To select a melody for the Door Chime
1: Remove the Back Plate from the Bell
Push
2: Press the Melody Select button.
CR2032
3:The chime will play the newly selected
sound
4: Press again to select the next melody.
Note: For Front/Back door setup, select a
different melody in one of the Bell Pushes.
6 Selectable Melodies
1: Tubular 3-Note 4: Solo
2: Big Ben 5: Tubular Score
3: Tubular 2-Note 6: Clarinet
1: plug Chime into a UK 3pin 1: plug Chime into a UK 3pin
socket, 220 – 240V ~ 50Hz. socket, 220 – 240V ~ 50Hz.
2: Switch the socket on. 2: Switch the socket on.
3: Chime will 'Beep' on Start
1: Press and hold the 'VOL'
buttons on both Door
Chimes, until the Chimes
'Beep Beep' (6 Seconds)
Adding Additional Chime/Bell Push:
2: Press the Bell Push within
60 seconds to learn the
Bell Push to the chimes.
3: The Chimes will ring to
confirm setup, wait 60
seconds for the Chimes
to exit the learn mode
before repressing the Bell
Push.
Additional Chime
To add an additional Chime unit to the Door Chime kit
1: Press and hold the 'VOL' button on your New Door Chime, until the
Chime goes 'Beep Beep' (6 Seconds)
2: Press the Bell Push within 60 seconds to learn the additional
Chime to the Bell Push.
3: Chime will ring to confirm setup, wait 60 seconds for the Chime to
exit the learn mode before repressing the bell push.
Additional Bell Push
To add an additional Bell Push to the Door
Chime kit
1: Press and hold the 'VOL' button on your
Door Chime, until the Chime goes
'Beep Beep' (6 Seconds)
2: Press the Bell Push within 60 seconds
to learn the additional Bell Push to the
Chime
3: Chime will ring to confirm setup, wait 60 seconds for the Chime
to exit the learn mode before repressing the bell push.
For Front/back door setup, select a different melody in one of
the Bell Pushes - See Melody Selection.
Note: Maximum of 6 Bell Pushes can be learnt to a single Chime
To select the Chime Volume level, press the 'VOL'
button on the chime There are 4 selectable volume
levels, the Door Chime is pre-set to the loudest
volume setting.
Default
Volume
New Chime
Front Door
Back Door