Lenovo IdeaCentre K330B Hardware Replacement Manual
Lenovo ideacentre k330b hardware replacement guide v5.0
Hide thumbs
Also See for IdeaCentre K330B:
- User manual (37 pages) ,
- Hardware maintenance manual (57 pages) ,
- Safety and warranty manual (49 pages)
Related Manuals for Lenovo IdeaCentre K330B
Summary of Contents for Lenovo IdeaCentre K330B
-
Page 1: Hardware Replacement Guide
Machine type: 10062/7727 10073/1169 10066/7747 10067/7748 IdeaCentre K3 Series Hardware Replacement Guide Version 5.0 2011.03 31048526... - Page 2 Hardware Replacement Guide © Copyright Lenovo 2011. All rights reserved. LIMITED AND RESTRICTED RIGHTS NOTICE: If data or software is delivered pursuant a General Services Administration “GSA” contract, use, reproduction, or disclosure is subject to restrictions set forth in Contract No. GS-35F-05925.
-
Page 3: Table Of Contents
Contents Overview ..................1 Chapter 1 Locations ..............5 Locating components and connectors ...........5 Identifying parts on the system board ..........10 Chapter 2 Replacing hardware ..........15 General information ..............15 Removing the computer cover .............15 Removing the front bezel .............17 Replacing a memory module ............18 Replacing the hard disk drive ............19 Replacing an optical drive ............20... -
Page 4: Overview
Do not open your computer or attempt any repairs before reading the “Important safety information” in the Safety and Warranty Guide that was included with your computer. An electronic copy of the Safety and Warranty Guide can also be obtained online from the Lenovo® Support Web site at: http://consumersupport.lenovo.com. Hardware Replacement Guide... -
Page 5: Additional Information Resources
Additional information resources The most up-to-date information for your computer is available online at: http://consumersupport.lenovo.com. You can find the following information: • CRU removal and installation • Publications • Troubleshooting • Parts • Links to other useful sources of information... - Page 6 When handling parts and other computer components, the following precautions should be taken in order to avoid static electricity damage: • Limit your movements, as such movements can cause the build-up of static electricity. • Always handle parts and other computer components with care, including handling adapters, memory modules, system boards, and microprocessors by their edges.
- Page 7 Hardware Replacement Guide...
-
Page 8: Chapter 1 Locations
Locations Chapter This chapter provides illustrations to help you locate the various connectors, controls and components in your computer. To remove the computer cover, refer to the section in this manual entitled “Removing the computer cover”. Locating components and connectors The following illustrations will help you to locate the various components and connectors in your computer. -
Page 9: Front View
Power supply PCI Express adapter card System fan Memory modules Microprocessor fan and heat sink Hard disk drive PCI Express adapter connector Optical drive Front view The two following illustrations show the location of the connectors on the front of the computer. -
Page 10: Rear View Of The Chassis
Optical drive (some models are equipped with only one optical drive) Power dial switch Rear view of the chassis The following illustrations show the location of the connectors on the rear of the computer. IdeaCentre K330 Voltage selection switch (Selected models only) Power connector PS/2 keyboard connector PS/2 mouse connector... - Page 11 IdeaCentre K330A/IedaCentre K330B Voltage selection switch (Selected models only) Power connector PS/2 keyboard connector PS/2 mouse connector HDMI connector USB connectors (4) On-board VGA connector Ethernet connector Audio connectors (3) Standalone graphic card (Selected models only) Expansion card slots (Access connectors for any installed PCI express cards) Hardware Replacement Guide...
- Page 12 IdeaCentre K335 Voltage selection switch (Selected models only) Power connector PS/2 keyboard connector PS/2 mouse connector eSATA connector USB connectors (6) HDMI connector On-board VGA connector Ethernet connector Audio connectors (6) Standalone graphic card (Selected models only) Expansion card slots (Access connectors for any installed PCI express cards) Hardware Replacement Guide...
-
Page 13: Identifying Parts On The System Board
Identifying parts on the system board The system board (also known as the “mainboard” or “motherboard”) is the main circuit board in your computer. It provides basic computer functions and supports a variety of devices that are factory-installed or that you can install later. The following illustrations show the locations of the different parts on the system board. - Page 14 Power fan connector Front panel connector Front USB connectors (3) Serial (com2) connector Front audio connector PCI express X 1 adapter connectors (2) PCI express X 16 adapter connectors (2) System fan connector 12V power connector IdeaCentre K330A Microprocessor and heat sink Microprocessor fan connector Memory connectors (4) Thermal sensor header connector...
- Page 15 Front USB connectors (3) Serial(com2) connector Front audio connector PCI express X 1 adapter connectors (3) PCI express X 16 adapter connector System fan connector 12V power connector IdeaCentre K330B Microprocessor and heat sink Microprocessor fan connector Hardware Replacement Guide...
- Page 16 Memory connectors (2) Thermal sensor header connector Power connector SATA connectors (4) Front panel connector Front USB connectors (3) Serial(com2) connector Front audio connector PCI express X 1 adapter connectors (3) PCI express X 16 adapter connector System fan connector 12V power connector IdeaCentre K335 Hardware Replacement Guide...
- Page 17 Microprocessor and heat sink Microprocessor fan connector Memory connectors (4) Thermal sensor header connector Power connector SATA connectors (4) eSATA connector Power Fan connector Front panel connector Front USB connectors (3) Serial(com2) connector Front audio connector PCI express X 1 adapter connectors (2) PCI express X 16 adapter connectors (2) System fan connector 12V power connector...
-
Page 18: Chapter 2 Replacing Hardware
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com. Note: Use only parts provided by Lenovo. - Page 19 3. Disconnect all cables attached to the computer. This includes power cords, input/output (I/O) cables, and any other cables that are connected to the computer. Refer to “Locating connectors on the rear of the computer”. 4. Remove the two screws that secure the computer cover at the rear of the chassis.
-
Page 20: Removing The Front Bezel
Removing the front bezel To remove the front bezel: 1. Remove the computer cover. Refer to “Removing the computer cover”. Note: For this procedure, it helps to lay the computer on its side. 2. Remove the front bezel by releasing the three plastic tabs inside the chassis and push the bezel outward as shown. -
Page 21: Replacing A Memory Module
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com. To replace a memory module: 1. Remove the computer cover. Refer to “Removing the computer cover”. -
Page 22: Replacing The Hard Disk Drive
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com. To replace the hard disk drive: 1. Remove the computer cover. Refer to “Removing the computer cover”. -
Page 23: Replacing An Optical Drive
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com To replace an optical drive 1. Remove the computer cover. Refer to “Removing the computer cover”. -
Page 24: Replacing The System Fan Assembly
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com To replace the system fan assembly: 1. Remove the computer cover. Refer to “Removing the computer cover”. - Page 25 4. Pull the system fan assembly out of chassis. Hardware Replacement Guide...
- Page 26 5. Install the new system fan assembly by aligning the rubber mounts of the system fan assembly with the holes on the chassis and push the rubber mounts through the holes. 6. Pull on the tips of the rubber mounts until the fan assembly is in place. 7.
-
Page 27: Replacing The Heat Sink Assembly
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at: http://consumersupport.lenovo.com To replace the heat sink assembly: 1. Remove the computer cover. Refer to “Removing the computer cover”. - Page 28 7. Use the thermal grease syringe to place five drops of grease on the top of the microprocessor. Each drop of grease should be 0.03ml (3 tick marks on the grease syringe). 8. Install the new heat sink and fan assembly on the heat sink retention bracket. 9.
-
Page 29: Replacing A Pci Express Adapter
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at: http://consumersupport.lenovo.com To replace an adapter: 1. Remove the computer cover. Refer to “Removing the computer cover”. - Page 30 3. Install the new adapter into the same adapter connector. 4. Ensure that the new adapter is fully seated into the adapter connector. 5. At the rear of the computer, turn the adapter latch to the closed position to secure the adapter. 6.
- Page 31 Note 1: Replacement of some models equipped with graphic adapter bracket is different. Please remove the plastic bracket first as the following: 1. Remove the two screws that secure the plastic bracket at the bottom of the chassis. 2. Lift the plastic bracket out of the chassis. 3.
- Page 32 1. Install the plastic bracket into the chassis so that the screw holes in the plastic bracket align with those in the chassis. Let the slot on the plastic bracket to clip onto the adapter. 2. Fit the two screws to secure the plastic bracket. Note: Use only screws provided by Lenovo. Hardware Replacement Guide...
- Page 33 Note 2: Replacement of some models equipped with graphic adapter bracket is different. Please remove the bracket first as the following: 1. Remove the screw that secures the bracket at the side of the chassis. 2. Press the pin on one end of the metal bracket and pull the metal bracket straight out of the chassis.
- Page 34 1. Install the metal bracket into the chassis so that the screw hole in the metal bracket aligns with the hole in the chassis. Let the slot on the metal bracket clip the adapter. 2. Screw back the screws on the metal bracket. Note: Use only the screw provided by Lenovo. Hardware Replacement Guide...
-
Page 35: Replacing The Cpu
Hardware Maintenance Manual (HMM) for the computer. To obtain copies of the Safety and Warranty Guide or HMM, go to the Support Web site at http://consumersupport.lenovo.com To replace an CPU 1. Remove the computer cover. Refer to “Removing the computer cover”. - Page 36 6. Lift the microprocessor straight up and out of the socket. Notes: a. Note the orientation of the notches on the microprocessor. This is important when reinstalling the microprocessor on the new system board. b. Do not drop anything onto the microprocessor socket while it is exposed.
- Page 37 9. Holding the microprocessor with your fingers, position the microprocessor so that the notches on the microprocessor are aligned with the tabs in the microprocessor socket. Important: To avoid damaging the microprocessor contacts, do not tilt the microprocessor when installing it into the socket. 10.
-
Page 38: Replacing The Keyboard
Replacing the keyboard To replace the keyboard: 1. Remove any media (disket, CDs, or memory cards) from the drives, shut down the computer, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. 3. Locate the connector for the keyboard. Refer to “Locating connectors on the rear of the computer”... -
Page 39: Replacing The Mouse
Replacing the mouse To replace the mouse: 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down the computer, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. 3. Locate the connector for the mouse. Refer to “Locating connectors on the front of the computer”... -
Page 40: Replacing The External Speaker
Replacing the external speaker 1. Remove any media (diskettes, CDs, or memory cards) from the drives, shut down the computer, and turn off all attached devices. 2. Unplug all power cords from electrical outlets. 3. Locate the Speaker. Refer to “Locating connectors on the rear of the computer”... - Page 41 5. To update your configuration settings, refer to “Starting the Setup Utility” in the Hardware Maintenance Manual. Note: In most areas of the world, Lenovo requires the return of the defective CRU. Information about this will either come with the CRU or will arrive a few days after the CRU has been delivered.
-
Page 42: Chapter 3 Appendix
Thank you for using Lenovo products. Carefully read all documents shipped with your computer before you install and use the product for the first time. Lenovo is not responsible for any loss except when caused by installation and operations performed by Lenovo professional service personnel. -
Page 43: Trademarks
Phenom, AMD Sempron, Catalyst, Cool ‘n’ Quiet, CrossFire, PowerPlay, Radeon, and The Ultimate Visual Experience are trademarks of Advanced Micro Devices, Inc. Other company, product, or service names referred to herein or in other Lenovo publications may be trademarks or service marks of others. All rights reserved.