1. Manuals
  2. Brands
  3. Black Widow Security Manuals
  4. Remote Starter
  5. BW RAS 400
  6. Installation manual

Black Widow Security BW RAS 400 Installation Manual

Remote auto start for keyless entry and add-on remote start modules
Hide thumbs
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual
REMOTE AUTO START
FOR KEYLESS ENTRY AND ADD-ON REMOTE START MODULES
INSTALLATION MANUAL
BEFORE INSTALLING THIS PRODUCT PLEASE READ
THIS INSTALLATION MANUAL THOROUGHLY!!
This remote start product is intended for
installation on vehicles equipped with automatic
transmissions and electronic fuel injection only!
DO NOT INSTALL THIS UNIT INTO A MANUAL
TRANSMISSION VEHICLE AS IT COULD RESULT IN
SERIOUS INJURY OR DEATH.
• This product must be installed by qualified
personnel according to these instructions and
observing all safety features.
• The system should be placed into the valet
mode when parked inside a garage or being left for
service.
• Always notify service personnel that the
vehicle is equipped with a Remote Starter.
• Only start the vehicle in a well ventilated area.
Do not use in a closed garage or indoors.
ITEMS INCLUDED:
• Main unit
• Remote transmitter(s)*
• Plug In LED
• Plug in program switch
• Harness kit with 2 heavy duty fuse holders
• Hood pinswitch
• Extended range receiver module*
• Owner's manual
*S models are provided with single transmitter only.
Add-on modules do not include transmitters.
OPTIONAL ACCESSORIES:
• VAC-10 Vacuum Switch Kit
• APP-1 Universal OEM transponder bypass kit
• APV-1 GM VATS, Passlock I&II bypass kit
• PDLM-3 Power door lock relay module
Before you begin the installation:
• Verify that the vehicle is equipped with
electronic fuel injection.
• Verify that the vehicle is equipped with an
automatic transmission.
• Check to see if the vehicle is equipped with any
type of factory security system.
• Check to see if there is a pinswitch for the
hood, if not one must be installed.
• Verify that the vehicle starts and idles
properly before you start the installation.
• Verify with the customer the desired location
for the program switch and LED.
• Always use a multimeter when verifying
vehicle wiring.
Remote Start Installation Notes:
The remote start unit senses the vehicle's
successful start using one of the following methods:
1. Current sense
2. Tachometer sense
3. Spark or coil wire sense
4. Using optional vacuum switch.

Advertisement

Table of Contents
loading

Related Manuals for Black Widow Security BW RAS 400

Summary of Contents for Black Widow Security BW RAS 400

  • Page 1 REMOTE AUTO START FOR KEYLESS ENTRY AND ADD-ON REMOTE START MODULES INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This remote start product is intended for OPTIONAL ACCESSORIES: installation on vehicles equipped with automatic • VAC-10 Vacuum Switch Kit transmissions and electronic fuel injection only! •...

  • Page 2: Main Harness

    If the Current Sense feature of the remote start provides +12V output to heater and/or air unit does not allow proper operation, the tach conditioning system. Some cars may have more sense/spark sense wire may be used, or an optional than one accessory wire.
  • Page 3 • GRAY WIRE - Ground When Running Output (-). 3-Pin Red Connector: Plug-in connector port for Connect to a relay for starter anti-grind protection. optional features harness. (See installation diagrams). The GRAY wire • GREEN/BLACK WIRE - 3rd channel output (-). provides ground for starter anti-grind protection Connect to a relay for optional trunk release etc.

  • Page 4: Programmable Features

    to the feature you wish to change. The LED and Program #6: Lock Before & After Engine Crank parking lights will flash each time the switch is On = Lock when remote start activates pushed. (Example: to program feature #3 press Off = Disabled the program switch 3 times).
  • Page 5 with anti-theft systems that use either a resistor coded key or a passive transponder that disables Valet Mode the fuel system unless a properly coded key is When the Valet mode is activated, the vehicle will inserted into the ignition cylinder. To integrate a not start using the remote, but keyless entry remote starter into these vehicles, you must functions will still operate.
  • Page 6 SECURITY/REMOTE START WIRING DIAGRAM GREEN DOOR LOCK OUTPUT (-) +12V CONSTANT OUTPUT BLUE DOOR UNLOCK OUTPUT (-) GREEN/BLACK TRUNK OUTPUT (-) FACTORY DISARM OUTPUT (-) YELLOW VACUUM SWITCH INPUT SWITCH WHITE PARKING LIGHT OUTPUT (+) +12V INPUT BROWN NOT USED BLACK GROUND INPUT ORANGE...

  • Page 7: Remote Start Troubleshooting

    REMOTE START TROUBLESHOOTING Problem Probable Cause Suggested Correction Unit will not operate. All power inputs are not Main Inputs (heavy gauge red connected to +12V. wires) and small red wire on main harness must be connected to +12V. Keyless Entry features operate System in Service Mode LED is Turn ignition key to on position, but vehicle will not start.

  • Page 8: Power Door Lock Diagrams

    POWER DOOR LOCK POSITIVE TRIGGER DOOR LOCK CIRCUIT: DIAGRAMS: TO POSITIVE LOCK WIRE TO POSITIVE UNLOCK WIRE This module provides negative LOCK RELAY UNLOCK RELAY door lock outputs. Positive GREEN WIRE BLUE WIRE FROM ALARM FROM ALARM trigger or reverse polarity installations require two SPDT 12V+ relays or the PDLM-3 Power...

This manual is also suitable for:

400

Table of Contents