Table of Contents
Advertisement
Quick Links
1
Channel
INSTALLATION MANUAL
Before Installing:
1. Read the INSTRUCTIONS!
2. USE A DIGITAL OR ANALOG
VOLT/OHM METER
3. BEFORE MOUNTING THE PRODUCT
CHECK THE POSSIBLE LOCATIONS
FOR THE SIREN AND LED BEFORE
YOU PERMANENTLY INSTALL THEM.
4. PROTECT THE VEHICLE BY USING
FENDER COVERS.
5. ROLL DOWN THE DRIVER'S WIN-
DOW BEFORE STARTING THE INSTAL-
LATION.
6. ALWAYS LOOK BEFORE DRILLING.
MAKE SURE YOU WILL NOT CAUSE
DAMAGE TO VEHICLE HOSES, ELECTRI-
CAL LOOMS OR PHYSICAL DAMAGE
TO VEHICLE.
S E L F - C O N TA I N E D
S E C U R I T Y S Y S T E M
1
B W - 1 0 6 0
Timing Information:
Automatic reset time: 45 seconds,
Panic output reset time: 45 seconds,
Arming time: (when all inputs are mon-
itored): 3 seconds-active arm.
Armed output: The Gray wire will pro-
duce a grounded output when system is
armed.
Flashing Parking Light Output:
Armed: 1 second pulsed, Disarmed: 2-one
second pulses. System triggered: 1 second
pulse on, 1 second off, repeated for 45
seconds.
Input Zone Out Feature:
If a door input remains on for 4 consecu-
tive cycles (45 seconds) that input will be
ignored. If the input returns to a non-trig-
gered state for 30 seconds it will be mon-
itored by the system again.
Advertisement
Table of Contents
Related Manuals for Black Widow 1 Channel
Summary of Contents for Black Widow 1 Channel
-
Page 1: Installation Manual
B W - 1 0 6 0 S E L F - C O N TA I N E D S E C U R I T Y S Y S T E M Channel INSTALLATION MANUAL Before Installing: Timing Information: 1. -
Page 2: Programmable Features
PROGRAMMABLE FEATURES 5. Code Learning Mode: If you wish to “teach” the system different remote To program these specific features controls: follow the procedure: a. Make sure system is disarmed or in 1. Anti Car Jacking: Turn the ignition key to the ON position.Within 5 seconds valet mode, press and hold button #2 for 5 seconds. -
Page 3: Installation Instructions
INSTALLATION 3. Connect Starter INSTRUCTIONS: Disable Relay: (Optional) Using a volt/ohm meter locate the starter 1. Mount the Siren: wire (normally a heavier gauge wire) off Locate a suitable place under the hood, of the ignition switch.The meter will read away from hot and moving engine parts 12V+ only during cranking.When the such as manifolds, turbo chargers, fan... - Page 4 shows 12V+ when only the parking lights key is turned off, it will keep the alarm are switched on. European vehicles may from arming via the remote. require an additional relay if they have separate wires that switch on the left and 9.
-
Page 5: Status Indicator (Led) Functions
STATUS INDICATOR (LED) FUNCTIONS Off= System off in Active Mode Slow Flash= System Armed Rapid Flash= System was triggered On Solid= 3 second final prearm state On Solid= (when disarmed) -Input is open. SILENT TEST MODE When the system is disarmed the LED will go solid every time an input is triggered. You can check the shock sensor, doors, hood, trunk, and the auxiliary sensor input as well. -
Page 6: Led Status
CHIRP STATUS LED STATUS A) 1 Chirp = System Armed A) Fast Flashing = System has been triggered B) 2 Chirps = System Disarmed Steady Flashing = System Armed C) 3 Chirps = System has been triggered D) 4 Chirps= Alarm armed but there is a trigger that remains open L.E.D. - Page 7 TERMINAL NUMBERING AND WIRE COLOR CODES COLOR FUNCTION FUNCTION +12V In Main Power. Connect this wire to the battery POSITIVE (+) terminal with the supplied 5 amp fuse installed at the BATTERY end of the wire! Be sure to read the CAUTION in item 4 of the installation instructions.
-
Page 8: Troubleshooting
TROUBLESHOOTING SYMPTOM PROBABLE CAUSE SUGGESTED CORRECTION Antenna wire is grounded, mod- Make sure antenna is not con- Range is poor ule is picking up interference nected to anything, relocate mod- from vehicles electrical system ule away from vehicle computer modules Vehicle starts when Wrong starter wire was cut Locate proper starter wire...