Advertisement
4. CHANGE THE OPERATION CODE FOR BOTH
TRANSMITTER AND RECEIVER (CONT)
3
If the connector is placed on the top and middle posts, that column is
set on " + " . If the connector is placed on the middle and bottom posts,
that column is set on " - ". If the connector is removed completely, (not
placed on any posts), it is set to " 0 ".
(see diagram for examples of how to
set a column to the three different
positions). When removing a con-
nector to set a column to " 0 ", save
the connector in case you change
the code at a later date.
4
After setting up the code connectors on the transmitter, you
are ready to set the same code on the receiver.
Remove the receiver from the electrical outlet before
changing the code.
WARNING
5
Remove the screw that holds
the connector cover, and remove
the cover.
6
You will see 10 connectors. For connec tors "1" to "9", the
settings must match with those of the transmitter.
7
For connector "10" on the receiver, set the connector on "+" if you
are using button "1" to control this receiver. If you are planning to
use button "2" to control this receiver, you need to remove this
connector. See diagram below.
Connector 10 set to "+"
RECEIVER
Connector 10 "Removed"
RECEIVER
8
Put the cover and screw back onto the receiver. Plug the receiver
into an electrical outlet.
9
Put the battery cover back onto the transmitter.
10
Press the designated button on the transmitter to operate the garage
door.
'
'
0
'+'
Connectors
1 to 9 are
the same.
BATTERY
TRANSMITTER
Button 1- Left Button
TRANSMITTER
Button 2- Right button
12 volt alkaline battery (size 23A)
(included).
It is time to change the battery
when the red LED on the trans-
mitter does not turn on when
either button is pressed.
'-'
There are 2 buttons on your transmitter, the other
button can be used to control another Skylink
Door Receiver Model 318R (sold separately) or Skylink
Wireless Switch Receiver Model SW-318R (sold
separately).
You can add as many additional transmitters as you
want to control the same receiver. Simply set the
same operation code on all transmitters with the same
code setting on the receiver. Skylink
Transmitter Model 318TN and Keyless Entry Transmit-
ter Model 318K to work with your receiver. For more
information, please visit our website at
www.skylinkhome.com or contact us.
RISK OF ELECTRICAL SHOCK. FOR INDOOR USE ONLY.
CAUTION : DISCONNECT POWER BEFORE CODE CHANGING.
REPLACE COVER AFTER CODE CHANGING.
Maximum Rating:
Input : 120VAC 60Hz 2W
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) This device must accept any interference
received, including interference that may cause undesired operation.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
If, within one year from date of purchase, this product should become defective
(except battery), due to faulty workmanship or materials, it will be repaired or
replaced, without charge. Proof of purchase and a Return Authorization are required.
If you would like to order Skylink's products or have difficulty getting them to work,
please :
1. visit our FAQ website at www.skylinkhome.com , or
2. email us at support@skylinkhome.com , or
3. call our toll free at 1-800-304-1187 from Monday to Friday, 9 am to 5 pm EST.
Fax (800) 286-1320
CUSTOMER SERVICE
17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3
Email:support@skylinkhome.com
http://www.skylinkhome.com
P/N. 101A206-005 Rev.5
US Patent. D380895
©2005 SKYLINK GROUP
5. BATTERY
6. ADDITIONAL RECEIVER
®
Garage
7. ADDITIONAL TRANSMITTER
®
offers Keychain
8. CAUTION
9. FCC
10. WARRANTY
11. CUSTOMER SERVICE
®
Advertisement
