ASRock. ASRock assumes no responsibility for any errors or omissions that may appear in this manual. With respect to the contents of this manual, ASRock does not provide warranty of any kind, either expressed or implied, including but not limited to the implied warran- ties or conditions of merchantability or fitness for a particular purpose.
In case any modifications of this manual occur, the updated ver- sion will be available on ASRock website without further notice. You may find the latest VGA cards and CPU support lists on ASRock’s website as well. ASRock website http://www.asrock.com...
1.2 Specifications Platform - CEB Form Factor: 12.0-in x 10.5-in, 30.5 cm x 26.7 cm - Premium Gold Capacitor design (100% Japan-made high- quality Conductive Polymer Capacitors) ® - Supports Intel Core i7 processor family for the LGA 2011 Socket - Digi Power Design - 24 + 2 Power Phase Design - Dual-Stack MOSFET (DSM) (see CAUTION 1)
Page 7
- Supports Energy Efficient Ethernet 802.3az - Supports Dual LAN with Teaming function - Supports PXE Rear Panel I/O I/O Panel - 1 x PS/2 Keyboard Port - 1 x Optical SPDIF Out Port - 8 x Ready-to-Use USB 2.0 Ports - 2 x eSATA Connectors - 4 x Ready-to-Use USB 3.0 Ports - 2 x RJ-45 LAN Port with LED (ACT/LINK LED and SPEED...
Page 9
4GB for the reservation for system usage under Windows ® / Vista . For Windows OS with 64-bit CPU, there is no such limitation. ® You can use ASRock XFast RAM to utilize the memory that Windows cannot use.
Page 10
<F6> key during the POST or the <F2> key to enter into the BIOS setup menu to access ASRock Instant Flash. Just launch this tool and save the new BIOS file to your USB flash drive,...
Page 11
14. ASRock XFast RAM is a new function that is included into F-Stream. It ® fully utilizes the memory space that cannot be used under Windows 32-bit CPU.
Page 12
19. Although this motherboard offers stepless control, it is not recommended to perform over-clocking. Frequencies other than the recommended CPU bus frequencies may cause instability of the system or damage the CPU. 20. While CPU overheat is detected, the system will automatically shutdown. Before you resume the system, please check if the CPU fan on the moth- erboard functions properly and unplug the power cord, then plug it back again.
1.4 I/O Panel USB 2.0 Ports (USB01) ** 10 Front Speaker (Lime) LAN RJ-45 Port Microphone (Pink) IEEE 1394 Port (IEEE 1394) eSATA Connectors LAN RJ-45 Port USB 3.0 Ports (USB3_0_1) USB 3.0 Ports (USB3_23) USB 2.0 Ports (USB3_67) Central / Bass (Orange) USB 2.0 Ports (USB3_4_5) Rear Speaker (Black) USB 2.0 Ports (USB3_2_3)
Chapter 2: Installation This is a CEB form factor (12.0" x 10.5", 30.5 x 26.7 cm) motherboard. Before you install the motherboard, study the configuration of your chassis to ensure that the motherboard fits into it. Make sure to unplug the power cord before installing or removing the motherboard.
2.3 CPU Installation For the installation of Intel 2011-Pin CPU, please follow the steps below. 2011-Pin Socket Overview Before you insert the 2011-Pin CPU into the socket, please check if the CPU surface is unclean or if there are any bent pins in the socket. Do not force to insert the CPU into the socket if above situation is found.
Page 17
Step 2-2. Locate Pin1 and the two orientation key notches. orientation key notch alignment key Pin1 orientation key notch alignment key 2011-Pin CPU 2011-Pin Socket For proper inserting, please ensure to match the four orientation key notches of the CPU with the four alignment keys of the socket. Step 2-3.
2.4 Installation of CPU Fan and Heatsink This motherboard is equipped with a 2011-Pin socket that supports Intel 2011- Pin CPUs. Please adopt the type of heatsink and cooling fan compliant with Intel 2011-Pin CPU to dissipate heat. Before you install the heatsink, you need to spray thermal interface material between the CPU and the heatsink to improve heat dis- sipation.
2.5 Installation of Memory Modules (DIMM) This motherboard provides eight 240-pin DDR3 (Double Data Rate 3) DIMM slots, and supports Quad Channel Memory Technology. For quad channel con- figuration, you always need to install identical (the same brand, speed, size and chip-type) DDR3 DIMM in the slots, so that Quad Channel Memory Tech- nology can be activated.
Installing a DIMM Please make sure to disconnect power supply before adding or remov- ing DIMMs or the system components. Step 1. Unlock the DIMM slot by pressing the retaining clips outward. Step 2. Align the DIMM on the slot such that the notch on the DIMM matches the break on the slot.
Installing an expansion card Step 1. Before installing an expansion card, please make sure that the power supply is switched off or the power cord is unplugged. Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation. Step 2.
2.7 ASRock Game Blaster Configuration This section explains how to configure your ASRock Game Blaster. 2.7.1 THX TRUSTUDIO PRO THX TruStudio Pro Click the power button on the left to activate or deactivate. Surround Control the level of audio immersion in music, movies and games.
Page 24
2.7.2 CRYSTALVOICE Select a recording device Mic Volume Control the level of mic volume. Mic Boost Control the level of mic boost. CrystalVoice Click the power button on the left to activate or deactivate. Morph your voice into different characters and accents. Smart Volume Be heard clearly without having to shout or whisper.
Page 25
2.7.3 SCOUT MODE Scout Mode Enable or disable scout mode. This proprietary technology allows you to hear your enemies from further away, giving you a distinct tactical advantage in combat. Hot Key Configuration Configure hot keys to enable or disable scout mode.
Page 26
2.7.4 SPEAKERS/HEADPHONES Speakers / Headphones Configuration Select the device connected. If there are both speakers and Optional Speakers: front headphones connected, please select the device you Center desire to use as audio output. Enable or disable center speaker. Subwoofer Enable or disable subwoofer. Rear pair Enable or disable rear pair speakers.
Page 27
2.7.5 MIXER Playback Speakers Control the level of speakers playback. SPDIF-Out Control the level of SPDIF-Out playback. Balance Control the level of various speaker’s balance. Input Device Select input device. What U Hear Control the level of playback redirect.
Page 28
2.7.6 EQUALIZER Choose from Flat, Acoustic, Classical, Country, Dance, Jazz, New Age, Pop, Rock and Vocal. 2.7.7 JACK SETUP...
Page 29
Device Connected: Select the device connected. 5.1 Surround 7.1 EX Surround Stereo and Line-In Show Jack Setup dialog when an audio jack is inserted Enable or disable Jack Setup dialog.
Page 30
2.7.8 ADVANCED FEATURES Play stereo mix to digital output Enable or disable play stereo mix to digital output.
Page 31
2.7.9 PROFILE User Profiles You can save, load or delete your user profiles. The default is <Custom>.
Page 32
Note 1. If you want to hear your own voice through the microphone (Playback mode). You can change your settings to "playback mode" by checking the "Listen to this device" box in Control panel Sound Recording Microphone Properties Listen. 2. If you want to change your playback device to a SPDIF-Out device, go into Control panel Sound Playback, then right click on SPDIF-Out and...
2.8 SLI , 3-Way SLI , 4-Way SLI and Quad SLI Operation Guide ® This motherboard supports NVIDIA , 3-Way SLI , 4-Way SLI and Quad (Scalable Link Interface) technology that allows you to install up to four ® identical PCI Express x16 graphics cards. Currently, NVIDIA technology ®...
Page 34
If required, connect the auxiliary power source to the PCI Express graph- ics cards. Step3. Align and insert the ASRock SLI_Bridge_3S Card to the goldfingers on each graphics card. Make sure the ASRock SLI_Bridge_3S Card is firmly in place. ASRock SLI_Bridge_3S Card Step4.
Page 35
Repeat this step on the three graphics cards. Step3. Align and insert the ASRock 3-Way SLI Bridge Card to the goldfingers on each graphics card. Make sure the ASRock 3-Way SLI Bridge Card is firmly in place. ASRock 3-Way SLI Bridge Card Step4.
Page 36
Repeat this step on the other graphics cards. Step3. Align and insert an ASRock SLI Bridge Card to the goldfingers of the first and second graphics card. Install the second ASRock SLI Bridge Card to the goldfingers of the third and fourth graphics card. Connect the second and the fourth graphics card with the ASRock SLI_Bridge_3S Card.
2.8.2 Driver Installation and Setup Install the graphics card drivers to your system. After that, you can enable the Multi- ® Graphics Processing Unit (GPU) feature in the NVIDIA nView system tray utility. Please follow the below procedures to enable the multi-GPU feature. ®...
Page 38
G. Reboot your system. H. You can freely enjoy the benefits of SLI or Quad SLI ® For Windows Vista / Vista 64-bit / 7 / 7 64-bit OS: (For 3-Way SLI or 4-Way SLI mode) A. Follow steps A to E on page 37. B.
Page 39
2.9 CrossFireX , 3-Way CrossFireX , 4-Way CrossFireX Quad CrossFireX Operation Guide This motherboard supports CrossFireX , 3-way CrossFireX , 4-way CrossFireX and Quad CrossFireX . CrossFireX technology offers the most advantageous means available of combining multiple high performance Graphics Processing Units (GPU) in a single PC.
Page 40
Step 2. Connect two Radeon graphics cards by installing a CrossFire Bridge on the CrossFire Bridge Interconnects on the top of the Radeon graphics cards. (The CrossFire Bridge is provided with the graphics card you pur- chase, not bundled with this motherboard. Please refer to your graphics card vendor for details.) CrossFire Bridge Step 3.
Page 41
2.9.1.2 Installing Three CrossFireX -Ready Graphics Cards ® Step 1. Install identical 3-Way CrossFireX -ready graphics cards that are AMD certified because different types of graphics cards will not work together properly. (Even the GPU chips version shall be the same.) Insert one graphics card into PCIE1 slot, another graphics card to PCIE3 slot, and the other graphics card to PCIE5 slot.
Page 42
2.9.1.3 Installing Four CrossFireX -Ready Graphics Cards ® Step 1. Install identical 4-Way CrossFireX -ready graphics cards that are AMD certified because different types of graphics cards will not work together properly. (Even the GPU chips version shall be the same.) Insert one graphics card into PCIE1 slot, another graphics card into PCIE3 slot, the third graphics card into PCIE5 slot and the last graphics card into PCIE7 slot.
Page 43
2.9.2 Driver Installation and Setup Step 1. Power on your computer and boot into OS. Step 2. Remove the AMD drivers if you have any VGA drivers installed in your system. The Catalyst Uninstaller is an optional download. We recommend using this utility to uninstall any previously installed Catalyst drivers prior to installation.
Although you have selected the option “Enable CrossFire ”, the CrossFireX function may not work actually. Your computer will automatically reboot. After restarting your computer, please confirm whether the option “Enable CrossFire ” in “AMD Catalyst Control Center” is selected or not; if not, please select it again, and then you are able to enjoy the benefits of CrossFireX Step 7.
2.11 ASRock Smart Remote Installation Guide ASRock Smart Remote is only used for ASRock motherboards with a CIR header. Please refer to the procedures below for the quick installation and usage of ASRock Smart Remote. Step1. Find the CIR header located next to the USB 2.0 header on your...
Page 46
The Multi-Angle CIR Receiver does not support Hot-Plug. Please install it before you boot the system. * ASRock Smart Remote is only supported by some ASRock motherboards. Please refer to ASRock's website for the motherboard support list: http://www.asrock.com...
2.12 Jumpers Setup The illustration shows how jumpers are setup. When the jumper cap is placed on pins, the jumper is “Short”. If no jumper cap is placed on pins, the jumper is “Open”. The illustration shows a 3-pin jumper whose pin1 and pin2 are “Short”...
2.13 Onboard Headers and Connectors Onboard headers and connectors are NOT jumpers. Do NOT place jumper caps over these headers and connectors. Placing jumper caps over the headers and connectors will cause permanent damage of the motherboard! Serial ATA2 Connectors These four Serial ATA2 (SATA2) connectors support SATA data (SATA2_0_1: see p.13, No.
Page 49
Serial ATA (SATA) Either end of the SATA data Data Cable cable can be connected to the SATA / SATA2 / SATA3 hard (Optional) disks or the SATA2 / SATA3 / SAS connectors on this motherboard. Serial ATA (SATA) Please connect the black end of Power Cable the SATA power cable to the power connector on each drive.
Page 50
USB 3.0 Header Besides four default USB 3.0 ports on the I/O panel, there are (19-pin USB3_4_5) two USB 3.0 headers on this (see p.13, No. 12) motherboard. Each USB 3.0 header can support two USB 3.0 ports. (19-pin USB3_6_7) (see p.13, No.
Page 51
C. Connect Ground (GND) to Ground (GND). D. MIC_RET and OUT_RET are for HD audio panel only. You don’t need to connect them for AC’97 audio panel. E. To activate the front mic. ® For Windows XP / XP 64-bit OS: Select “Mixer”.
Page 52
Chassis Speaker Header Please connect the chassis speaker to this header. (4-pin SPEAKER 1) (see p.13, No. 34) Power LED Header Please connect the chassis power LED to this header to (3-pin PLED1) indicate system power status. (see p.13, No. 35) The LED is on when the system is operating.
Page 53
Though this motherboard provides 4-Pin CPU fan (Quiet Fan) support, the 3-Pin CPU fan still can work successfully even without the fan speed control function. If you plan to connect the 3-Pin CPU fan to the CPU fan connector on this motherboard, please connect it to Pin 1-3.
Page 54
SLI/XFIRE Power Connector It is not necessary to use this connector, but please connect it (4-pin SLI/XFIRE_PWR1) with a hard disk power (see p.13, No. 50) SLI/XFIRE_PWR1 connecor when two graphics cards are plugged to this motherboard. (4-pin SLI/XFIRE_PWR2) (see p.13, No. 37) SLI/XFIRE_PWR2 IEEE 1394 Header Besides one default IEEE 1394...
Page 55
The Installation Guide of Front USB 3.0 Panel Step 1 Screw the 2.5” HDD/SSD to the Front Step 2 Prepare the bundled Front USB 3.0 Panel, four USB 3.0 Panel with four HDD screws. HDD screws, and six chassis screws. Step 3 Step 4 Screw the Front USB 3.0 Panel to the...
2.14 Smart Switches The motherboard has three smart switches: power switch, reset switch and clear CMOS switch, allowing users to quickly turn on/off or reset the system to clear the CMOS values. Power Switch Power Switch is a smart switch, allowing users to quickly turn (PWRBTN) on/off the system.
2.15 Dr. Debug Dr. Debug is used to provide code information, which makes troubleshooting even easier. Please see the diagrams below for reading the Dr. Debug codes. Status Code Description 0x00 Not used 0x01 Power on. Reset type detection (soft/hard) 0x02 AP initialization before microcode loading 0x03...
Page 58
0x37 Post-Memory North Bridge initialization is started 0x38 Post-Memory North Bridge initialization (North Bridge module specific) 0x39 Post-Memory North Bridge initialization (North Bridge module specific) 0x3A Post-Memory North Bridge initialization (North Bridge module specific) 0x3B Post-Memory South Bridge initialization is started 0x3C Post-Memory South Bridge initialization (South Bridge module specific) 0x3D...
Page 59
0x62 Installation of the South Bridge Runtime Services 0x63 CPU DXE initialization is started 0x64 CPU DXE initialization (CPU module specific) 0x65 CPU DXE initialization (CPU module specific) 0x66 CPU DXE initialization (CPU module specific) 0x67 CPU DXE initialization (CPU module specific) 0x68 PCI host bridge initialization 0x69...
Page 60
0xA6 SCSI Detect 0xA7 SCSI Enable 0xA8 Setup Verifying Password 0xA9 Start of Setup 0xAA Reserved for ASL 0xAB Setup Input Wait 0xAC Reserved for ASL 0xAD Ready To Boot event 0xAE Legacy Boot event 0xAF Exit Boot Services event 0xB0 Runtime Set Virtual Address MAP Begin 0xB1...
2.16 Serial ATA (SATA) / Serial ATA2 (SATA2) Hard Disks Installation ® This motherboard adopts Intel X79 chipset that supports Serial ATA (SATA) / Serial ATA2 (SATA2) hard disks and RAID (RAID 0, RAID 1, RAID 5, RAID 10 and Intel Rapid Storage 3.0) functions.
2.18 Hot Plug and Hot Swap for SATA / SATA2 HDDs This motherboard supports Hot Plug and Hot Swap for SATA / SATA2 in RAID / ® AHCI mode. Intel X79 chipset provides hardware support for Advanced Host controller Interface (AHCI), a new programming interface for SATA host controllers developed through a joint industry effort.
3. Please make sure the SATA / SATA2 / SATA3 driver is installed into system properly. The latest SATA / SATA2 / SATA3 driver is available on our support website: www.asrock.com 4. Make sure to use the SATA power cable & data cable from our motherboard package.
Page 64
How to Hot Plug a SATA / SATA2 / SATA3 HDD: Points of attention, before you process Hot Plug: Please follow the instructions below to process Hot Plug. Improper procedures will cause the SATA / SATA2 / SATA3 HDD damage and data loss. Step 2 Step 1 Please connect the SATA power cable’s...
2.21 Driver Installation Guide To install the drivers to your system, please insert the support CD to your optical drive first. Then, the drivers compatible to your system can be auto-detected and listed on the support CD driver page. Please follow the order from top to bottom to install those required drivers.
® 2.23 Installing Windows 7 / 7 64-bit / Vista / Vista 64-bit Without RAID Functions ® If you want to install Windows 7 / 7 64-bit / Vista / Vista 64-bit OS on your SATA / SATA2 / SATA3 HDDs without RAID functions, please follow the procedures below according to the OS you install.
2.24 Untied Overclocking Technology This motherboard supports Untied Overclocking Technology, which means during overclocking, BCLK enjoys better margin due to fixed PCI / PCIE buses. Before you enable Untied Overclocking function, please enter “Overclock Mode” option of UEFI setup to set the selection from [Auto] to [Manual]. Therefore, BCLK is untied during overclocking, but PCI / PCIE buses are in the fixed mode so that BCLK can operate under a more stable overclocking environment.
2.25 Teaming Function Operation Guide Dual LAN with Teaming function enabled on this motherboard allows two single connections to act as one single connection for twice the transmission bandwidth, making data transmission more effective and improving the quality of transmission of distant images.
Page 69
4. Click the Create Team tab. * The Create Team tab appears only if there are teamable adapters available. 5. Click the Team Name field to enter a team name. 6. Click the Team Type field to select a team type. 7.
Page 70
9. Type the value for Team MTU. 10. Click Create to save the team information. 11. Repeat steps 5. through 10. to define additional teams. As teams are defined, they can be selected from the team list, but they have not yet been created. Click the Preview tab to view the team structure before applying the changes.
Page 71
* Not all network adapters made by others are supported or fully certified for teaming. 14. Configure the team IP address. a. From Control Panel, double-click Network Connections. b. Right-click the name of the team to be configured, and then click Properties. c.
Chapter 3: UEFI SETUP UTILITY 3.1 Introduction ASRock Interactive UEFI is a blend of system configuration tools, cool sound ef- fects and stunning visuals. Not only will it make BIOS setup less difficult but also a lot more amusing. This section explains how to use the UEFI SETUP UTILITY to configure your system.
3.1.2 Navigation Keys Please check the following table for the descriptions of each navigation key. Navigation Key(s) Function Description + / - To change option for the selected items <Tab> Switch to next function <PGUP> Go to the previous page <PGDN>...
3.3 OC Tweaker Screen In the OC Tweaker screen, you can set up overclocking features. Load CPU EZ OC Setting You can use this option to load CPU EZ overclocking settings. Please note that overclocking may cause damage to your CPU and motherboard. It should be done at your own risk and expense.
Page 75
Use this item to add voltage when CPU is in Turbo mode. Additional Turbo Voltage Use this item to add voltage when CPU is in Turbo mode. Active Processor Cores Use this item to select the number of cores to enable in each processor package.
Page 76
DRAM tRAS Use this item to change RAS# Active Time (tRAS) Auto/Manual setting. The default is [Auto]. DRAM tRFC Use this item to change Refresh Cyle Time (tRFC) Auto/Manual setting. The default is [Auto]. DRAM tWR Use this item to change Write Recovery Time (tWR) Auto/Manual setting. The default is [Auto].
Page 77
Use this item to change ODT WR (CH C) setting. The default is [Auto]. ODT NOM (CH C) Use this item to change ODT NOM (CH C) setting. The default is [Auto]. ODT WR (CH D) Use this item to change ODT WR (CH D) setting. The default is [Auto]. ODT NOM (CH D) Use this item to change ODT NOM (CH D) setting.
Page 78
DRAM tWWDR Use this item to change DRAM tWWDR Auto/Manual setting. The default is [Auto]. DRAM tRRDD Use this item to change DRAM tRRDD Auto/Manual setting. The default is [Auto]. DRAM tRRDR Use this item to change DRAM tRRDR Auto/Manual setting. The default is [Auto].
3.4 Advanced Screen In this section, you may set the configurations for the following items: CPU Configu- ration, North Bridge Configuration, South Bridge Configuration, Storage Configura- tion, Super IO Configuration, ACPI Configuration, USB Configuration and ME Sub- system. Setting wrong values in this section may cause the system to malfunction.
3.4.1 CPU Configuration CPU Ratio Setting Use this item to change the ratio value of this motherboard. Intel Hyper Threading Technology To enable this feature, a computer system with an Intel processor that sup- ports Hyper-Threading technology and an operating system that includes ®...
Page 81
CPU Power Management Configuration Intel SpeedStep Technology Intel SpeedStep technology is Intel’s new power saving technology. Pro- cessors can switch between multiple frequencies and voltage points to en- able power saving. The default value is [Enabled]. Configuration options: ® [Enabled] and [Disabled]. If you install Windows Vista / 7 and want to enable this function, please set this item to [Enabled].
3.4.2 North Bridge Configuration LSI Link Speed This allows you to select LSI Link Speed. The default value is [GEN3]. PCIE 1 & PCIE 2 & PCIE 3 Link Speed This allows you to select PCIE 1&2&3 Link Speed. The default value is [GEN2].
3.4.3 South Bridge Configuration Restore on AC/Power Loss This allows you to set the power state after an unexpected AC/power loss. If [Power Off] is selected, the AC/power remains off when the power re- covers. If [Power On] is selected, the AC/power resumes and the system starts to boot up when the power recovers.
Page 84
Onboard Debug Port LED Use this item to enable or disable Onboard Debug Port LED.
3.4.4 Storage Configuration SATA Mode This item is for SATA3_0, SATA3_1 and SATA2_0 to SATA2_3 ports. Use this to select SATA mode. Configuration options: [IDE Mode], [AHCI Mode], [RAID Mode] and [Disabled]. The default value is [AHCI Mode]. AHCI (Advanced Host Controller Interface) supports NCQ and other new features that will improve SATA disk performance but IDE mode does not have these advantages.
Page 86
Marvell SATA3 controller as Boot Device. ® We recommend to use Intel X79 SATA ports (SATA3_0, SATA3_1 and SATA2_0 to SATA2_3) for your bootable devices. This will minimum your boot time and get the best performance. But if you still want to boot from the LSI controller or Marvell SATA3 controller, you can enable these from the UEFI.
3.4.5 Super IO Configuration Serial Port Use this item to enable or disable the onboard serial port. Serial Port Address Use this item to set the address for the onboard serial port. Configuration options: [3F8h / IRQ4] and [3E8h / IRQ4]. Infrared Port Use this item to enable or disable the onboard infrared port.
3.4.6 ACPI Configuration Suspend to RAM Use this item to select whether to auto-detect or disable the Suspend-to- RAM feature. Select [Auto] will enable this feature if the OS supports it. Check Ready Bit Use this item to enable or disable the feature Check Ready Bit. PS/2 Keyboard Power On Use this item to enable or disable PS/2 keyboard to turn on the system from the power-soft-off mode.
3.4.7 USB Configuration USB 2.0 Controller Use this item to enable or disable the use of USB 2.0 controller. USB 3.0 Controller Use this item to enable or disable the use of USB 3.0 controller. Legacy USB Support Use this option to select legacy support for USB devices. There are four configuration options: [Enabled], [Auto], [Disabled] and [UEFI Setup Only].
3.5 Tool Sound Effect Enable or disable sound effects in the setup utility. System Browser System Browser can let you easily check your current system configuration in UEFI setup. OMG(Online Management Guard) Administrators are able to establish an internet curfew or restrict internet access at specified times via OMG.
Page 92
that you must be running on a DHCP configured computer in order to en- able this function. Easy RAID Installer Easy RAID Installer can help you to copy the RAID driver from a support CD to your USB storage device. After copying the RAID driver to your USB storage device, please change “SATA Mode Selection”...
This allows you to set SB fan 1’s speed. Configuration options: [Full On] and [Automatic mode]. The default value is [Automatic mode]. Target SB Temperature This allows you to set the target temperature to activate ASRock X-FAN. The default value is [50 C/122 Target Fan Speed This allows you to set target fan’s speed.
3.7 Boot Screen In this section, it will display the available devices on your system for you to config- ure the boot settings and the boot priority. Setup Prompt Timeout This shows the number of seconds to wait for setup activation key. 65535(0XFFFF) means indefinite waiting.
3.9 Exit Screen Save Changes and Exit When you select this option, the following message “Save configuration changes and exit setup?” will pop-out. Select [Yes] to save the changes and exit the UEFI SETUP UTILITY. Discard Changes and Exit When you select this option, the following message “Discard changes and exit setup?”...
Click on a specific item then follow the installation wizard to install it. 4.2.4 Contact Information If you need to contact ASRock or want to know more about ASRock, welcome to visit ASRock’s website at http://www.asrock.com; or you may contact your...
Page 98
Installing OS on a HDD Larger Than 2TB in AHCI Mode ® This motherboard adopts UEFI BIOS that allows Windows OS to be installed on a large size HDD (>2TB). Please follow the procedures below to install the operating system. ®...
RAID drivers into a USB flash disk. You can download the driver from ASRock's website and unzip the file into a USB flash disk OR copy the file from ASRock motherboard support CD. (please copy the files under the following directory: 32 bit: ..\i386\Win7_Vista_Intel..
Page 100
E. Please keep the USB flash disk installed until the system's first reboot. ® F. Continue to install OS by following the Windows instructions. ® 5. Follow Windows Installation Guide to install OS. ® If you install Windows 7 64-bit / Vista 64-bit on a large hard disk (ex.
Page 101
B. Disable “Volume Shadow Copy” service. a. Type “computer management” in the Start Menu, then press “Enter”. b. Go to “Services and Applications>Services”; Then double click “Volume Shadow Copy”.
Page 102
c. Set “Startup type” to “Disable” then Click “OK”. C. Reboot your system. D. After reboot, please start to install motherboard drivers and utilities. ® Windows 7 64-bit: A. Please request the hotfix KB2505454 through this link: http://support.microsoft.com/kb/2505454/ ® B. After installing Windows 7 64-bit, install the hotfix kb2505454.