Installation Instructions - Air King LIN46M Operating Manual

INSTALLATION INSTRUCTIONS

CAUTION:
MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
NOTE: Outdoor Kitchen Professional Range Hoods are approved for use in covered
outdoor kitchens only. Proper duct adapters, ducting, chimneys, roof/wall caps, etc.
must be utilized as called out in the following instructions. Do not install the hood in an
uncovered area directly exposed to the elements.
SECTION 1
Preparing the Insert
1. Unpack hood from the carton and confirm that all pieces are present. In addition to
the range hood you should have:
12 - S crews (46", 58" models - 14)
2 - Halogen Bulbs (58" models - 4)
1 - Duct Adapter
1 - Grease Trough
2 - Grease Baffles (46", 58" models - 3)
1 - Instruction/Safety Sheet
NOTE: Some hoods may be shipped with a protective plastic adhered to the underside
of the unit. It is recommended to leave this in place during installation to protect it from
scratching. Remove when the installation is complete.
SECTION 2
Preparing the Area
CAUTION:
MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
CAUTION:
WHEN CUTTING OR DRILLING INTO WALL DO NOT DAMAGE
ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.
1. Cut an appropriately sized hole for the cabinet or canopy the liner will be mounted
into (Figure 1):
Model LIN34M: 34.5" x 19.375"
Model LIN40M: 40.5" x 19.375"
Model LIN46M: 46.5" x 22.625"
Model LIN58M: 58.5" x 22.625"
Figure 1
NOTE: The hood must be mounted a minimum of 24" and a maximum of 36" from the
cooking surface.
SECTION 3
Mounting the Liner
CAUTION:
DUE TO THE WEIGHT AND BULK OF THE UNIT, IT IS RECOMMENDED
THAT THREE PEOPLE ARE PRESENT DURING INSTALLATION TO LIFT, HOLD, AND SECURE
THE UNIT IN PLACE.
1. Lift unit up into position so that the bottom flanges are in solid contact with the bottom
of the canopy or cabinet. Using the included wood mounting screws, secure the unit
to the canopy or cabinet by driving the screws through the holes (Figure 2).
Figure 2
6728024M New 8-10
34.5"/40.5"/
46.5"/58.5"
19.375"
22.625"
Canopy
Flange
Screws
www.airkinglimited.com
NOTE: If additional support is required, install a 2" x .75" strip of wood (34" wide) between
the back of the canopy (rear wall) and the hood. When installing the wood strip to the
back of the canopy, locate studs in the wall to support the weight of the canopy. Center
the wood strip 11.5" from the bottom of the canopy and attach the strip to at least two
studs in the rear wall (do not fasten the strip to drywall only). Lift unit up into position so
that the bottom flanges are in solid contact with the bottom of the canopy or cabinet. Using
wood screws and washers (not included) secure the hood to the wood strip through the
two keyholes in the back of the hood. Using the included wood mounting screws, secure
the unit to the canopy or cabinet by driving the screws through the holes (Figure 3).
OPTIONAL ADDITIONAL SUPPORT
Wood
Mounting
Strip
Figure 3
SECTION 4
Ducting
CAUTION:
ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL
BUILDING CODES.
WARNING:
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
1. Determine the type of ducting you will require (Figure 4).
Horizontal
Wall Cap
Figure 4
NOTE: For models using the B600 blower (LIN34, LIN40), a minimum of 6" diameter
outlet adapter & ducting is required to achieve the proper air flow. The B1125 (LIN46,
LIN58) requires a minimum 10" diameter adapter and ducting.
NOTE: When the duct termination is similar to that shown in Figure 4 (passing through
the wall to which the hood is mounted) the installation requires special consideration.
Depending upon where the wall studs are located, it may be necessary to cut one
or more of the wall studs and install a header and footer to transfer the load to the
adjacent studs. Additional studs may need to be framed into the opening to attach dry
wall or secure the hood. If this is your situation Air King recommends that you hire a
professional and comply with all applicable codes.
2. Install the proper sized outlet adapter to the hood by matching up the four holes on
the flange of the adapter to the four corresponding holes on the hood and secure
in place with the provided screws. Ensure an airtight seal around the adapter by
securing all connections with ducting tape (Figure 5).
Outlet Adapter
Hood
Figure 5
Canopy
Washer
Screws
Roof Cap
Outlet
Adapter
Ducting
Screws
Flange
Flange
Vertical
2 of 8