Applied Operations; Alarm Operation - JVC RMP-2580U - Remote Controller For Color Domes Instructions Manual

3. APPLIED OPERATIONS

ALARM OPERATION

Alarm input signals can be applied to the DATA I/O terminals on the rear panel. The unit functions in either the
ALARM PRIORITY mode or the MANUAL PRIORITY mode when an alarm signal is input. ( REF. : "CONTROL
UNIT SCREEN" on page 28 and "PRIORITY item of ALARM SCREEN" on page 32.)
CAMERA CAMERA
SETUP POWER
ALARM
MENU MENU SET
KEY LOCK
LENS LENS
1
SPEED
4
IRIS IRIS
CLOSE OPEN OPEN
FOCUS FOCUS
7
NEAR NEAR FAR
AF AF
ZOOM ZOOM TELE CLEAR
WIDE WIDE
Alarm Operation Modes
When an alarm signal is received, this unit performs the following operations.
<Alarm priority mode>
The video is switched to the camera position from which the alarm signal is received.
An alarm signal will automatically override and cancel the operation of either AUTO PATROL or AUTO SEQUENCE. (AUTO
SEQUENCE: In A mode only.)
The preset alarm title is displayed in the preset size.
The ALARM indicator blinks and the buzzer sounds. ( REF. : "BUZZER TIME" on page 32 for the setting method.)
The CAMERA display indicates the number ID of the camera which has given the alarm signal.
The UNIT ALARM output is turned ON.
<Manual priority mode>
When an alarm signal is received during manual operation (except during the AUTO PAN, AUTO PATROL and AUTO SE-
QUENCE operations), the alarm operation does not start.
When an alarm signal is received from a camera other than the camera being controlled manually, the alarm operation starts
but, unlike in the alarm priority mode, the buzzer does not sound and the camera in question is not automatically selected.
<Example when Alarm 1 and Alarm 2 are input during AUTO SEQUENCE in the A Mode>
Alarm input 1
Alarm input 2
Camera 1 alarm time
Camera 2 alarm time
UNIT ALARM
output duration
MONITOR OUTPUT 1
Set in item "TIME" in the AUTO SEQUENCE screen.
CAMERA2 CAMERA3
MONITOR OUTPUT 2
Time period of switching by CAMERA SW.
• In B mode, the MONITOR OUTPUT 2 connector outputs the same video as the MONITOR OUTPUT 1 connector.
For B Mode connection. REF. : [Applied System (B Mode)] on page 21.
B Mode output signal REF. : [B Mode] on page 22.
• While the MENU screen is displayed, the alarm signal is not accepted.
RM-P2580 RM-P2580
REMOTE CONTROL UNIT REMOTE CONTROL UNIT
POSITION POSITION
AUTO AUTO F-1 F-2 F-3 F-3
CAMERA/POSITION CAMERA/POSITION PAN/TILT PAN/TILT
2 3
CAMERA CAMERA POSI- POSI-
TION
5 6
OPTION OPTION OPTION OPTION
1 2
8 9 AUTO AUTO AUTO AUTO
PAN PAN PATROL PATROL
0
ENTER
/HOME /HOME
Alarm input 1
ALARM TIME
CAMERA3 CAMERA
CAMERA4 CAMERA
TO CAMERA TO CAMERA
RX+ RX- TX+ TX-
POWER
OFF
ON
`
AC INPUT
1 2 3 4 5 6 7
ON
Alarm input 2
ALARM TIME
CAMERA
CAMERA
*Encircled number shows the alarm condition.
DATA I/O terminals
DATA I / O DATA I / O
UNIT UNIT CAMERA CAMERA SERIAL-1 SERIAL-1
COM COM 1 2 3 4 5 6 7 8 COM 9/1 COM 9/1 10/2 10/2 11/3 11/3 12/4 12/4 13/5 13/5 14/6 14/6 15/7 15/7 16/8 16/8 COM COM AUTO AUTO ALARM ALARM COM COM SW SW COM COM
VIDEO INPUT VIDEO INPUT
1 2 3 4 5 6 7 8
MONITOR MONITOR
OUTPUT OUTPUT
8
1 2 3 4 5 6 7 8
VIDEO OUTPUT
CAMERA2
CAMERA4 CAMERA5 CAMERA6 CAMERA7
SERIAL-2 SERIAL-2
MONITOR MONITOR
OUTPUT OUTPUT
1 2
CAMERA3
Time
17