Table of Contents
Advertisement
Quick Links
American DJ
TP-DMX24F
CHASE
CHASE
CHASE
CHASE
1
2
3
1
2
3
2
13
14
15
CONTROLS AND FUNCTIONS
1. CHASE 1-12 and LED indicator
2. CHANNEL 1-24 and LED indicator
3. CH 1-24 HOLD/FLASH selector
HOLD indicator/FLASH indicator
4. PAGE 1 / PAGE 2
PAGE 1 Selects CHASE 1 to 12
PAGE 2 Selects CHASE 13 to 24
5. REAL TIME /TAP SYNC
:
REAL-TIME
DEFINES THE DURATION OF EACH STEP WHEN PROGRAMMING
:
TAP SYNC
DEFINES THE RUNNING SPEED WHEN RUNNING THE PROGRAMS
6. ASSIGN SCENE /BLIND
a:ENTER OR EXIT FROM PROGRAMMING MODE
b: ASSIGN ONE CHANNEL TO ANY OTHER CHANNEL OF CHANNELS 1-24
ASSIGN SCENE / BLIND & CHANNEL 1-24
BLIND: PRESS
TO DESIGNATE MANUAL CONTROL OF THAT CHANNELS OUTPUT
SPECIFICATIONS:
POWER input: DC + 16V-22V • Current Requirement: >8OOmA • Power consumption: <12W
Output: DMX512 , MIDI IN, OUT, THRU• AUDIO input: 100mv-1 vp-p-p
Dimensions:19" x 3.5" x 1.5" (483mm x 178mm x 30mm) • Weight: 4 lbs. (2 kg)
© American DJ® Los Angeles CA 90058 USA • TP-DMX24F™ Instructions page 1
®
1
CHASE
CHASE
CHASE
4
5
6
7
4
5
6
7
16
17
18
19
User Instructions
™
24 Ch. DMX/Analog Programmable Touch Panel
CHASE
CHASE
CHASE
CHASE
8
9
10
11
8
9
10
11
20
21
22
23
3 8
4
6
10 9
RECORD
CHASE
CHASE
FLASH
BLIND
12
SIGNAL
MANUAL
PAGE 1
CHASE
STEP
STEP
^
^
PAGE 2
MIX
12
CHASE
AUDIO
REAL
PERCENT
TIME
TRAITS
CHASE
TAP
24
BLACK-
SYNC
OUT
11
5
7
14
15
16
STEP
DIMMER
SECOND
MINUTE
0.1SEC
10
1 SEC
3 SEC
8
5 SEC
10 SEC
6
30 SEC
1 MIN
3 MIN
4
5 MIN
2
10 MIN
SHOW
0
TIME
DIMMER
CHASE
AUDIO
12
13
Advertisement
Table of Contents
Summary of Contents for American DJ TP-DMX24F
-
Page 1: Controls And Functions
Output: DMX512 , MIDI IN, OUT, THRU• AUDIO input: 100mv-1 vp-p-p Dimensions:19” x 3.5” x 1.5” (483mm x 178mm x 30mm) • Weight: 4 lbs. (2 kg) © American DJ® Los Angeles CA 90058 USA • TP-DMX24F™ Instructions page 1... -
Page 2: Power Switch
CONTROLS AND FUNCTIONS Cont. 10 9 RECORD CHASE STEP DIMMER CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE CHASE FLASH BLIND SECOND MINUTE 0.1SEC SIGNAL MANUAL PAGE 1 CHASE STEP 1 SEC STEP 3 SEC 5 SEC PAGE 2 10 SEC 30 SEC... -
Page 3: Dmx Output
CONTROLS AND FUNCTIONS Cont. DMX OUTPUT 1:GND DC INPUT AUDIO 2:DATA- 3:DATA+ LINE INPUT +16V-+24V RANGE 500mA Min. 100MV-1VP-P 1:GND 2:DATA - 3:DATA + DC INPUT 16-24V 220mA min LINE INPUT (EXT AUDIO INPUT) JACK (lOOmV to 1 vp-p-p) MIDI IN Receives MIDI data MIDI OUT Transmit MIDI data output... -
Page 4: Manual Mode
OPERATING INSTRUCTIONS Cont.. 1. MAKE SURE THE TRANSFORMER IS CORRECT 16 TO 24 DC AND CORRECT POLARITY 2.Plug in transformer and turn on unit. LED’s for HOLD / FLASH, TRAITS CHASE, PAGE 1 and DIMMER are on. you are now in MANUAL MODE 1. - Page 5 OPERATING INSTRUCTIONS Cont. 2.1 CHASE PROGRAM Cont. At this point you can set the duration between this and the next step in the chase if you want to do this. (FIG13.) CHASE FADER or touch (FIG 5.) REAL TIME /TAP SYNC, wait until the interval is what you want, then touch (FIG 5.) REAL TIME /TAP SYNC again.
- Page 6 OPERATING INSTRUCTIONS Cont. 2.3 DIMMER SETTING IN MANUAL MODE To adjust DIMMING/VALUE of any channel in Manual mode. CHASE PROGRAM A. Enter mode, Touch any (FIG 2.) CHANNEL 1-24 when LED is on touch same channel again until LED starts to blink. You can now use (FIG12 ) DIMMER FADER to adjust output.
- Page 7 OPERATING INSTRUCTIONS Cont. 3. RECORD / CHASE cont. There are 3 ways to control the chase program 1. CHASE, 2. AUDIO, 3. MANUAL 3.1. CHASE control A. Set (FIG13.) CHASE FADER to SHOW position > 10 min. The Chase will be controlled by what ever time was programmed in section 2.1 ( The default setting is 0.3 sec) B.
-
Page 8: Midi Setting
OPERATING INSTRUCTIONS Cont. MIDI SETTING AND RUNNING MIDI SETTING Touch and hold (FIG.1.) CHASE 9, CHASE 10, CHASE 11,CHASE 12, while power is being turned CHASE 1, CHASE 2, CHASE 3 LEDs blink rapidly and (FIG14.) LCD DIGITAL DISPLAY READS A A A A A A this means console is in MIDI mode.