Asus P5GD2-X User Manual page 40

P5gd2-x user's manual for english edition
Hide thumbs Also See for P5GD2-X:
Table of Contents

Advertisement

2 . 2 .
2 .
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
2 .
2 .
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
P r i m a r y I D E c o n n e c t o r ( 4 0 - 1 p i n P R I _ I D E )
These connectors are for Ultra DMA 100/66 signal cables. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary IDE connector on the motherboard, a black connector for
an Ultra DMA 100/66 IDE slave device (optical drive/hard disk drive),
and a gray connector for an Ultra DMA 100/66 IDE master device (hard
disk drive). If you install two hard disk drives, you must configure the
second drive as a slave device by setting its jumper accordingly. Refer
to the hard disk documentation for the jumper settings.
P5GD2-X IDE connector
3 . 3 .
3 .
3 .
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
3 .
S e r i a l A T A c o n n e c t o r s
S e r i a l A T A c o n n e c t o r s
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
( 7 - p i n S A T A 1 , S A T A 2 , S A T A 3 , S A T A 4 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
P5GD2-X SATA connectors
Install the Windows
Pack1 or later before using Serial ATA.
1 - 2 8
1 - 2 8
1 - 2 8
1 - 2 8
1 - 2 8
Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
®
®
®
2000 Service Pack 4 or the Windows
PRI_IDE
NOTE: Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SATA2
GND
RSATA_TXP2
RSATA_TXN2
GND
RSATA_RXP2
RSATA_RXN2
GND
SATA1
GND
RSATA_TXP1
RSATA_TXN1
GND
RSATA_RXP1
RSATA_RXN1
GND
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
C h a p t e r 1 : P r o d u c t i n t r o d u c t i o n
SATA4
GND
RSATA_TXP4
RSATA_TXN4
GND
RSATA_RXP4
RSATA_RXN4
GND
SATA3
GND
RSATA_TXP3
RSATA_TXN3
GND
RSATA_RXP3
RSATA_RXN3
GND
®
XP Service

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents