Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Zanussi ZGS 782 ICT
Summary of Contents for Zanussi ZGS 782 ICT
- Page 1 Instruction booklet Gas hob ZGS 782 IT ZGS 782 ICT...
- Page 2 Thank you for selecting our appliance Thank you for selecting our appliance Thank you for selecting our appliance Thank you for selecting our appliance Thank you for selecting our appliance We wish you lots of enjoyment with your new appliance and we hope that you will consider our brand again when purchasing household appliances.
-
Page 3: Table Of Contents
Step by step instructions for an operation Hints and Tips Environmental information MANUFACTURER: ELECTROLUX HOME PRODUCTS ITALY S.P.A. Viale Bologna, 298 - 47100 Forlì - Italy ... 4 4 4 4 4 ... 7 7 7 7 7 ... 1 4... -
Page 4: Important Safety Information
Important Safety Information Y Y Y Y Y ou MUST r ou MUST read these war ou MUST r ou MUST r ead these war nings car ead these war ead these war ou MUST r ead these war using the hob. If you need assistance, contact our Customer using the hob. - Page 5 When using the hob for a long period time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands.
-
Page 6: Description Of The Hob
Description of the Hob 1. Hob Top 2. Auxiliary Burner 3. Semi-rapid Burner 4. Rapid Burner 5. Triple Crown 6. Control knobs... -
Page 7: Instructions For The User
Instructions for the User INSTALLATION Any gas installation must be carried out by a registered Any gas installation must be carried out by a registered Any gas installation must be carried out by a registered Any gas installation must be carried out by a registered Any gas installation must be carried out by a registered competent person, and in accordance with existing rules competent person, and in accordance with existing rules... -
Page 8: Operation
Operation Operation Operation Operation Operation Hob burners control knobs Hob burners control knobs Hob burners control knobs Hob burners control knobs Hob burners control knobs The symbols on the knobs mean that : there is no gas supply there is maximum gas supply there is minimum gas supply Lighting the burners Lighting the burners... - Page 9 Do not keep the control knob pressed for more than 15 seconds. If the burner does not light even after 15 seconds, release the control knob, turn it the "off" position and wait for at least one minute before trying to light the burner again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically.
- Page 10 Make sure pots do not protrude over the edges of the cooktop Make sure pots do not protrude over the edges of the cooktop...
-
Page 11: Maintenance And Cleaning
(e.g. vinegar substances (e.g. vinegar, salt, lemon substances (e.g. vinegar substances (e.g. vinegar substances (e.g. vinegar juice, etc.) on the cooktop. juice, etc.) on the cooktop. juice, etc.) on the cooktop. juice, etc.) on the cooktop. juice, etc.) on the cooktop. - Page 12 Pay attention when replacing the pan Pay attention when replacing the pan Pay attention when replacing the pan Pay attention when replacing the pan Pay attention when replacing the pan supports in order to avoid damaging supports in order to avoid damaging supports in order to avoid damaging supports in order to avoid damaging supports in order to avoid damaging...
-
Page 13: Something Not Working
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local Service Force Centre. SYMPTOM SYMPTOM SYMPTOM SYMPTOM SYMPTOM There is no spark when lighting the gas. The gas ring burns unevenly. If after all these checks, your hob still does not operate correctly, contact your local Service Force Centre. -
Page 14: Instructions For The Installer Instructions For The Installer
Instructions for the Installer Engineer technical data Engineer technical data Engineer technical data Engineer technical data Engineer technical data OVERALL DIMENSIONS OVERALL DIMENSIONS OVERALL DIMENSIONS OVERALL DIMENSIONS OVERALL DIMENSIONS CUT OUT DIMENSIONS CUT OUT DIMENSIONS CUT OUT DIMENSIONS CUT OUT DIMENSIONS CUT OUT DIMENSIONS SUPPL SUPPL... - Page 15 BURNER TYPE OF GAS POSITION NOMINAL THERMAL POWER NATURAL GAS 20 mbar NOMINAL FLOW VALUE = RATE 37.78 MJ/m NOZZLE REFERENCE Ws - 50.7 MJ/ m 1/100 mm NOMINAL THERMAL LPG GAS POWER 28-30/37 mbar NOMINAL FLOW VALUE = RATE 49.92 MJ/Kg NOZZLE REFERENCE 1/100 mm...
-
Page 16: Important Safety Requirements
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S. -
Page 17: Installation
The minimum distance combustible material or a cooker hood can be fitted above the hob is 650 mm. For appliances installed in the Republic of Ireland please refer to NSAI- Domestic Gas Installation I.S 813 Current Edition Section 7- Permitted Locations of Appliance. Installation IMPOR T T T T T ANT IMPOR... -
Page 18: Gas Connection
On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. FO 0264 A) End of shaft with nut B) Washer C) Elbow... -
Page 19: Building In
Building In B B B B B uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer uilding over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. -
Page 20: Fitting The Hob Into The Worktop
Fitting the Hob into the Worktop Carry out the building in of the hob as follows: • place the seals supplied with the hob on the front edge of the cut out. Then, place them at 86 mm from the side edges and at 10 mm from the rear edge, as shown in the diagram, taking care that the seals meet without overlapping. -
Page 21: Electrical Connections
Electrical Connections Any electrical work required to install this hob should be Any electrical work required to install this hob should be Any electrical work required to install this hob should be Any electrical work required to install this hob should be Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, carried out by a qualified electrician or competent person,... -
Page 22: Wiring Diagram
3) Connect the brown (live) wire to the terminal in the plug which is marked with the letter 'L' or coloured red. Upon completion there must be no cut, or stray strands of wire present and the cord clamp must be secure over the outer sheath. A cut off plug inserted into a 13 amp socket is a serious A cut off plug inserted into a 13 amp socket is a serious A cut off plug inserted into a 13 amp socket is a serious... -
Page 23: Fault Finding
Fault Finding Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check Preliminary Electrical Systems Check S T A R T S T A R T S T A R T S T A R T S T A R T Isolate appliance and carry out:... - Page 24 A. EARTH CONTINUITY CHECK A. EARTH CONTINUITY CHECK A. EARTH CONTINUITY CHECK A. EARTH CONTINUITY CHECK A. EARTH CONTINUITY CHECK Appliance must be electrically disconnected - meter set on W (Ohms) x 1 scale and adjust zero if necessary. — Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 W (Ohm), check all earth wires for continuity and all contacts clean and tight.
- Page 25 Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Ignition System / Gas Ignition Ignitor does not spark Check plug top fuse and replace if necessary Check polarity and earth continuity of supply point Check earth continuity...
-
Page 26: Commissioning
Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. -
Page 27: Conversion From Natural Gas To Lpg
Conversion from Natural Gas to LPG IMPOR IMPOR IMPOR IMPOR T T T T T ANT IMPOR The replacement/conversion from natural gas to LPG should only The replacement/conversion from natural gas to LPG should only The replacement/conversion from natural gas to LPG should only The replacement/conversion from natural gas to LPG should only The replacement/conversion from natural gas to LPG should only be undertaken by a competent person. -
Page 28: Guarantee/Customer Service
Standard guarantee conditions Standard guarantee conditions We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this Zanussi-Electrolux appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: ·... - Page 29 Customer Care Customer Care For general enquiries concerning your Electrolux appliance, or for further information on Electrolux products please contact our Customer Care Department by letter or telephone at the address below or visit our website at www.electrolux.co.uk Customer Care Department...
-
Page 30: European Guarantee
• The appliance is installed and used in accordance with instructions issued by Electrolux and is only used within the home, i.e. is not used for commercial purposes. • The appliance is installed in accordance with all relevant regulations in force within your new country of residence. - Page 32 356994801 01/08...