1. Manuals
  2. Brands
  3. HP Manuals
  4. Server
  5. ProLiant DL320e
  6. User manual

HP ProLiant DL320e User Manual

Hp proliant dl320e gen8 server user guide
Hide thumbs Also See for ProLiant DL320e:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Reference Manual
HP ProLiant DL320e Gen8 Server

User Guide

Abstract
This document is for the person who installs, administers, and troubleshoots servers and storage systems. This document is intended for experienced
IT professionals or end-users with no or prior hardware setup experience. HP assumes you are qualified in the servicing of computer equipment and
trained in recognizing hazards in products with hazardous energy levels.
Part Number: 682822-001
September 2012
Edition: 1

Advertisement

Table of Contents
loading

Related Manuals for HP ProLiant DL320e

Summary of Contents for HP ProLiant DL320e

  • Page 1: User Guide

    HP ProLiant DL320e Gen8 Server User Guide Abstract This document is for the person who installs, administers, and troubleshoots servers and storage systems. This document is intended for experienced IT professionals or end-users with no or prior hardware setup experience. HP assumes you are qualified in the servicing of computer equipment and trained in recognizing hazards in products with hazardous energy levels.
  • Page 2 Microsoft® and Windows® are U.S. registered trademarks of Microsoft Corporation. Intel® Xeon®, Pentium®, and Intel® Core™ are trademarks of Intel Corporation in the U.S. and other countries. Bluetooth® is a trademark owned by its proprietor and used by Hewlett-Packard Company under license.

  • Page 3: Table Of Contents

    Contents Component identification ....................... 7 Front panel components ..........................7 Front panel LEDs and buttons ......................8 Rear panel components ..........................8 Rear panel LEDs and buttons ......................9 System board components ........................10 DIMM slot locations ........................11 PCIe riser board slot definitions ....................... 11 System maintenance switch ......................
  • Page 4 Hardware options installation ....................... 32 Introduction ............................32 Security bezel option ..........................32 Drive options ............................32 Drive installation guidelines ......................33 Installing a non-hot-plug drive ......................33 Installing a hot-plug drive ........................ 34 Mini-SAS cable option ..........................35 Controller options ............................ 38 Installing a storage controller ......................
  • Page 5 Array Configuration Utility ......................69 Option ROM Configuration for Arrays ..................... 70 ROMPaq utility ..........................71 Automatic Server Recovery ......................71 USB support ..........................71 Redundant ROM support ........................ 71 Keeping the system current ........................72 Drivers ............................72 Software and firmware ........................72 Version control ..........................
  • Page 6 Support and other resources ......................88 Before you contact HP ..........................88 HP contact information ..........................88 Customer Self Repair ..........................88 Acronyms and abbreviations ......................96 Documentation feedback ......................100 Index ............................101 Contents 6...

  • Page 7: Component Identification

    Component identification Front panel components • Four-bay LFF drive model Item Description Optical drive Serial label pull tab USB connectors LFF drives • Eight-bay SFF drive model Item Description Optical drive USB connectors Serial label pull tab SFF drives Component identification 7...

  • Page 8: Front Panel Leds And Buttons

    Front panel LEDs and buttons Item Description Status UID LED/button Blue = Identification is activated. Flashing blue = System is being managed remotely. Off = Identification is deactivated. Power On/Standby button Green = System is on. and system power LED Flashing green = Waiting for power.

  • Page 9: Rear Panel Leds And Buttons

    Item Description Slot 2 PCIe x16 (16, 8, 4, 1)* Slot 1 PCIe x8 (4, 1)* Power supply 1 Power supply 2 Dedicated iLO management port (optional) UID LED button Serial connector Video connector USB connectors NIC 1/shared iLO management connector NIC connector 2 * For more information on the riser board slots supported by the onboard PCI riser connectors, see "PCIe riser board slot definitions (on page 11)."...

  • Page 10: System Board Components

    System board components Item Description PCI riser connectors* SD card slot System maintenance switch NMI header SATA connector Mini-SAS connector 4-pin power supply connector Front panel connectors Internal USB connector Fan connector 4 Fan connector 3 System battery Fan connector 2 Discovery service connector Fan connector 1 24-pin power supply connector...

  • Page 11: Dimm Slot Locations

    DIMM slot locations DIMM slots are numbered sequentially (1 through 4) for the processor. The supported AMP modes use the letter assignments for population guidelines PCIe riser board slot definitions The transfer rate of the PCIe riser board slot 2 depends on the processor model installed. The slot can either run in PCIe2 (5 GT/s) or PCIe3 (8 GT/s) rate.

  • Page 12: Nmi Header

    Switch Default Function Off = No function On = ROM reads configuration as invalid — Reserved 3, 4, 7, 8, 9, 10, 11, 12 When the system maintenance switch position 6 is set to the On position, the system is prepared to erase all system configuration settings from both CMOS and NVRAM.

  • Page 13: Drive Numbering

    Item Description Status Power supply 1 failure Red = Power supply failure Off = Normal Power supply 2 failure Red = Power supply failure Off = Normal Auxiliary power Green = Standby power indicator Off = Standby power invalid Processor error Yellow = Critical processor error Off = Normal Drive numbering...

  • Page 14: Fbwc Module Led Definitions

    Item Status Definition Flashing blue The drive carrier firmware is being updated or requires an update. Activity ring Rotating green Drive activity No drive activity Do not remove Solid white Do not remove the drive. Removing the drive causes one or more of the logical drives to fail.

  • Page 15: Fan Locations

    1 - Amber 2 - Green 3 - Green Interpretation The cache module is idle, the capacitor pack is charged, and the cache contains data that has not yet been written to the drives. Flashing 1 Hz A backup is in progress. The current backup is complete with no errors.

  • Page 16: T-10/T-15 Torx Screwdriver

    T-10/T-15 Torx screwdriver The server includes a T-10/T-15 Torx screwdriver located beside the capacitor pack holder. Use the screwdriver to loosen screws during hardware configuration procedures. Component identification 16...

  • Page 17: Operations

    Operations Power up the server Connect each power cord to the server. Connect each power cord to the power source. Press the Power On/Standby button. The server exits standby mode and applies full power to the system. The system power LED changes from amber to green.

  • Page 18: Remove The Server From The Rack

    IMPORTANT: The requirement of extending or removing the server from the rack when performing installation and maintenance procedures depends on the rail system used: If using a ball-bearing rail system, you can perform most installations and maintenance by • simply extending the server from the rack. •...

  • Page 19: Remove The Security Bezel (Optional)

    IMPORTANT: The requirement of extending or removing the server from the rack when performing installation and maintenance procedures depends on the rail system used: If using a ball-bearing rail system, you can perform most installations and maintenance by • simply extending the server from the rack. •...

  • Page 20: Install The Access Panel

    Disconnect each power cord from the power source. Disconnect each power cord from the server. Do one of the following: Extend the server from the rack (on page 17). Remove the server from the rack (on page 18). Open the locking latch, slide the access panel to the rear of the chassis, and then remove the access panel.

  • Page 21: Install The Air Baffle

    Remove the air baffle. Install the air baffle Place the air baffle on top of the server. Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack"...

  • Page 22: Install The Pci Riser Cage

    Power down the server (on page 17). Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Do one of the following: Extend the server from the rack (on page 17). Remove the server from the rack (on page 18). Remove the access panel (on page 19).
  • Page 23 Tighten the PCI riser cage thumbscrews. Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack" on page 28). Power up the server (on page 17). Operations 23...

  • Page 24: Setup

    Setup Optional installation services Delivered by experienced, certified engineers, HP Care Pack services help you keep your servers up and running with support packages tailored specifically for HP ProLiant systems. HP Care Packs let you integrate both hardware and software support into a single package. A number of service level options are available to meet your needs.

  • Page 25: Space And Airflow Requirements

    Space and airflow requirements To allow for servicing and adequate airflow, observe the following space and airflow requirements when deciding where to install a rack: • Leave a minimum clearance of 63.5 cm (25 inches) in front of the rack. •...

  • Page 26: Power Requirements

    Power requirements Installation of this equipment must comply with local and regional electrical regulations governing the installation of information technology equipment by licensed electricians. This equipment is designed to operate in installations covered by NFPA 70, 1999 Edition (National Electric Code) and NFPA-75, 1992 (code for Protection of Electronic Computer/Data Processing Equipment).

  • Page 27: Rack Warnings

    WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: Observe local occupational health and safety requirements and guidelines for manual • material handling. • Get help to lift and stabilize the product during installation or removal, especially when the product is not fastened to the rails.

  • Page 28: Identifying The Contents Of The Server Shipping Carton

    WARNING: When installing a server in a telco rack, be sure that the rack frame is adequately secured at the top and bottom to the building structure. Identifying the contents of the server shipping carton Unpack the server shipping carton and locate the materials and documentation necessary for installing the server.
  • Page 29 WARNING: This server is very heavy. To reduce the risk of personal injury or damage to the equipment: Observe local occupational health and safety requirements and guidelines for manual • material handling. • Get help to lift and stabilize the product during installation or removal, especially when the product is not fastened to the rails.

  • Page 30: Installing The Operating System

    WARNING: To reduce the risk of electric shock or damage to the equipment: • Do not disable the power cord grounding plug. The grounding plug is an important safety feature. Plug the power cord into a grounded (earthed) electrical outlet that is easily accessible at all •...

  • Page 31: Registering The Server

    To modify the server configuration ROM default settings, press F9 when prompted from the start up sequence to enter the RBSU. By default, RBSU runs in the English language. If you do not need to modify the server configuration and are ready to install the system software, press F10 to access Intelligent Provisioning.

  • Page 32: Hardware Options Installation

    Hardware options installation Introduction If more than one option is being installed, read the installation instructions for all the hardware options and identify similar steps to streamline the installation process. WARNING: To reduce the risk of personal injury from hot surfaces, allow the drives and the internal system components to cool before touching them.

  • Page 33: Drive Installation Guidelines

    Drive installation guidelines When adding drives to the server, observe the following general guidelines: • The system automatically sets all device numbers. • Populate drive bays based on the drive numbering sequence. Start from the drive bay with the lowest device number ("Drive numbering"...

  • Page 34: Installing A Hot-Plug Drive

    Install the drive in the carrier. Install the drive. Connect each power cord to the server. Connect each power cord to the power source. Power up the server (on page 17). Determine the status of the drive from the drive LED definitions (on page 13). Installing a hot-plug drive CAUTION: To prevent improper cooling and thermal damage, do not operate the server unless...

  • Page 35: Mini-Sas Cable Option

    Remove the drive blank. Prepare the drive. Install the drive. Determine the status of the drive from the drive LED definitions (on page 13). Mini-SAS cable option To connect the cable option: Power down the server (on page 17). Remove all power: Disconnect each power cord from the power source.
  • Page 36 Extend the server from the rack (on page 17). Remove the server from the rack (on page 18). Remove the access panel (on page 19). Remove the PCI riser cage (on page 21). Connect the Mini-SAS cable to the storage controller. Install the storage controller ("Installing a storage controller"...
  • Page 37 Low-profile controller connection Secure the excess length of the Mini-SAS cable in the cable clip. Connect the rest of the drive cables required in this drive configuration. For more information, see "Storage cabling (on page 55)." Install the access panel (on page 20). Do one of the following: Slide the server into the rack.

  • Page 38: Controller Options

    Power up the server (on page 17). Controller options The server ships with an embedded Smart Array B120i controller. For more information about the controller and its features, see the HP Dynamic Smart Array RAID Controller User Guide on the HP website (http://www.hp.com/support/DSA_RAID_UG_en).

  • Page 39: Installing The Fbwc Module And Capacitor Pack

    Power down the server (on page 17). Remove all power: Disconnect each power cord from the power source. Disconnect each power cord from the server. Do one of the following: Extend the server from the rack (on page 17). Remove the server from the rack (on page 18). Remove the access panel (on page 19).
  • Page 40 Remove the server from the rack (on page 18). Remove the access panel (on page 19). Remove the PCI riser cage (on page 21). CAUTION: When connecting or disconnecting the capacitor pack cable, the connectors on the cache module and cable are susceptible to damage. Avoid excessive force and use caution to avoid damage to these connectors.

  • Page 41: Optical Drive Option

    Press the opposite end of the capacitor pack in the holder. Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack"...
  • Page 42 Remove the optical drive blank. Retain the blank for future use. Remove the access panel (on page 19). If you are installing the optical drive in an LFF drive model, do the following: Thread the optical drive cable through the optical drive bay. Connect the cable to the optical drive.
  • Page 43 Four-bay LFF drive model Eight-bay SFF drive model If you are installing the optical drive in an SFF drive model, connect the optical drive cable to the optical drive. Connect the optical drive cable: Route the optical drive cable through the cable clip on the front chassis. Route the optical drive cable along the side of the system board, and then connect the cable to the system board.

  • Page 44: Memory Options

    — Four-bay LFF drive model — Eight-bay SFF drive model Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack" on page 28). Connect each power cord to the server.

  • Page 45: Hp Smartmemory

    IMPORTANT: This server does not support mixing LRDIMMs, RDIMMs, or UDIMMs. Attempting to mix any combination of these DIMMs can cause the server to halt during BIOS initialization. The server memory subsystem supports UDIMMs only. UDIMMs represent the most basic type of memory module and offer lower latency and (relatively) low power consumption, but are limited in capacity.

  • Page 46: Single-Rank And Dual-Rank Dimms

    Item Description Definition Data width x4 = 4-bit x8 = 8-bit Voltage rating L = Low voltage (1.35V) U = Ultra low voltage (1.25V) Blank or omitted = Standard Memory speed 12800 = 1600-MT/s 10600 = 1333-MT/s 8500 = 1066-MT/s DIMM type R = RDIMM (registered) E = UDIMM (unbuffered with ECC)

  • Page 47: Installing A Dimm

    Memory channel 1 consists of the two DIMMs that are closest to the processor. Memory channel 2 consists of the two DIMMs that are located farthest from the processor. • White DIMM slot indicate the first slot of a channel (3-A, 1-B). •...

  • Page 48: Expansion Board Options

    Install the DIMM. Install the air baffle (on page 21). Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack" on page 28). Connect each power cord to the server.

  • Page 49: Dedicated Ilo Management Port Option

    Identify the expansion slot compatible with the new option, and then remove the cover opposite that slot. Install the expansion board. Install the PCI riser cage (on page 22). IMPORTANT: The server does not power up if the PCI riser cage is not seated properly. Connect all necessary internal and external cables to the expansion board.
  • Page 50 Extend the server from the rack (on page 17). Remove the server from the rack (on page 18). Remove the access panel (on page 19). Using a flat screwdriver, toggle the knockout to loosen it, and then pull it out of the chassis. Install the dedicated iLO management module.

  • Page 51: Enabling The Dedicated Ilo Management Port

    Enabling the dedicated iLO management port The onboard NIC 1/shared iLO connector is set as the default system iLO port. To enable the installed dedicated iLO module: During the server startup sequence after module installation, to access iLO RBSU, press the F8 key. Select the Network menu.

  • Page 52: Installing The Trusted Platform Module Board

    • HP is not liable for blocked data access caused by improper TPM use. For operating instructions, see the encryption technology feature documentation provided by the operating system. Installing the Trusted Platform Module board WARNING: To reduce the risk of personal injury, electric shock, or damage to the equipment, remove the power cord to remove power from the server.

  • Page 53: Retaining The Recovery Key/Password

    Install the TPM security rivet by pressing the rivet firmly into the system board. Install the access panel (on page 20). Do one of the following: Slide the server into the rack. Install the server into the rack ("Installing the server into the rack"...
  • Page 54 Press the Esc key to exit the current menu, or press the F10 key to exit RBSU. Reboot the server. Enable the TPM in the OS. For OS-specific instructions, see the OS documentation. CAUTION: When a TPM is installed and enabled on the server, data access is locked if you fail to follow the proper procedures for updating the system or option firmware, replacing the system board, replacing a hard drive, or modifying OS application TPM settings.

  • Page 55: Cabling

    Cabling Cabling overview This section provides guidelines that help you make informed decisions about cabling the server and hardware options to optimize performance. For information on cabling peripheral components, refer to the white paper on high-density deployment at the HP website (http://www.hp.com/products/servers/platforms). CAUTION: When routing cables, always be sure that the cables are not in a position where they can be pinched or crimped.
  • Page 56 • Mini-SAS cable connected to a storage controller in the full-height expansion slot Item Description Power cable Capacitor pack cable 700-mm Mini-SAS cable for non-hot-plug drive configuration • Mini-SAS cable connected to a storage controller in the low-profile expansion slot Item Description Power cable...

  • Page 57: Four-Bay Lff Hot-Plug Drive Cage Cabling

    Four-bay LFF hot-plug drive cage cabling • Mini-SAS cable connected to the system board Item Description Power cable 560-mm Mini-SAS cable • Mini-SAS cable connected to a storage controller in the full-height expansion slot Item Description Power cable Capacitor pack cable 890-mm Mini-SAS cable Cabling 57...

  • Page 58: Eight-Bay Sff Hot-Plug Drive Cage Cabling

    • Mini-SAS cable connected to a storage controller in the low-profile expansion slot Item Description Power cable Capacitor pack cable 890-mm Mini-SAS cable Eight-bay SFF hot-plug drive cage cabling • Mini-SAS cables connected to a storage controller in the full-height expansion slot Item Description 560-mm Mini-SAS cable...

  • Page 59: Optical Drive Cabling

    Item Description Power cable Capacitor pack cable Optical drive cabling • LFF drive cage model Item Description Optical drive power cable Optical drive SATA cable • SFF drive cage model Cabling 59...

  • Page 60: Power Supply Cabling

    Item Description Optical drive power cable Optical drive SATA cable Power supply cabling Nonredundant power supply cabling Item Description 24-pin power supply cable 4-pin power supply cable Cabling 60...

  • Page 61: Redundant Power Supply Cabling

    Redundant power supply cabling Item Description 24-pin power supply cable 26-pin RPS cable 4-pin power supply cable CAUTION: The default and redundant power supplies in the server must have the same output power capacity. Verify that all power supplies have the same part number and label color. The system becomes unstable and might shut down when it detects mismatched power supplies.

  • Page 62: Software And Configuration Utilities

    Software and configuration utilities Server mode The software and configuration utilities presented in this section operate in online mode, offline mode, or in both modes. Software or configuration utility Server mode Online and Offline HP iLO (on page 62) Online and Offline Active Health System (on page 63) Online and Offline Integrated Management Log (on page 64)

  • Page 63: Active Health System

    iLO enables and manages the Active Health System (on page 63) and also features Agentless Management. All key internal subsystems are monitored by iLO. SNMP alerts are sent directly by iLO regardless of the host operating system or even if no host operating system is installed. HP Insight Remote Support software (on page 66) is also available in HP iLO with no operating system software, drivers, or agents.

  • Page 64: Intelligent Provisioning

    The data that is collected is managed according to the HP Data Privacy policy. For more information see the HP website (http://www.hp.com/go/privacy). The Active Health System log, in conjunction with the system monitoring provided by Agentless Management or SNMP Pass-thru, provides continuous monitoring of hardware and configuration changes, system status, and service alerts for various server components.

  • Page 65: Hp Insight Diagnostics

    HP Insight Diagnostics HP Insight Diagnostics is a proactive server management tool, available in both offline and online versions, that provides diagnostics and troubleshooting capabilities to assist IT administrators who verify server installations, troubleshoot problems, and perform repair validation. HP Insight Diagnostics Offline Edition performs various in-depth system and component testing while the OS is not running.

  • Page 66: Hp Insight Remote Support Software

    HP Insight Remote Support software HP strongly recommends that you install HP Insight Remote Support software to complete the installation or upgrade of your product and to enable enhanced delivery of your HP Warranty, HP Care Pack Service, or HP contractual support agreement. HP Insight Remote Support supplements your monitoring 24 x 7 to ensure maximum system availability by providing intelligent event diagnosis, and automatic, secure submission of hardware event notifications to HP, which will initiate a fast and accurate resolution, based on your product’s service level.

  • Page 67: Hp Service Pack For Proliant

    HP Service Pack for ProLiant SPP is a release set that contains a comprehensive collection of firmware and system software components, all tested together as a single solution stack for HP ProLiant servers, their options, BladeSystem enclosures, and limited HP external storage. SPP has several key features for updating HP ProLiant servers.

  • Page 68: Using Rbsu

    • Configuring memory options • Language selection For more information on RBSU, see the HP ROM-Based Setup Utility User Guide on the Documentation CD or the HP website (http://www.hp.com/support/rbsu). Using RBSU To use RBSU, use the following keys: • To access RBSU, press the F9 key during power-up when prompted. •...

  • Page 69: Boot Options

    Boot options Near the end of the boot process, the boot options screen is displayed. This screen is visible for several seconds before the system attempts to boot from a supported boot device. During this time, you can do the following: •...

  • Page 70: Option Rom Configuration For Arrays

    Advanced Capacity Expansion (SATA to SAS and SAS to SATA) Offline Split Mirror RAID 6 and RAID 60 RAID 1 (ADM) and RAID 10 (ADM) HP Drive Erase Video-On-Demand Advanced Controller Settings • Provides different operating modes, enabling faster configuration or greater control over the configuration options •...

  • Page 71: Rompaq Utility

    For more information about the controller and its features, see the HP Smart Array Controllers for HP ProLiant Servers User Guide on the HP website (http://www.hp.com/support/SAC_UG_ProLiantServers_en). To configure arrays, see the Configuring Arrays on HP Smart Array Controllers Reference Guide on the HP website (http://www.hp.com/support/CASAC_RG_en).

  • Page 72: Keeping The System Current

    NOTE: The server ships with the same version programmed on each side of the ROM. Safety and security benefits When you flash the system ROM, ROMPaq writes over the backup ROM and saves the current ROM as a backup, enabling you to switch easily to the alternate ROM version if the new ROM becomes corrupted for any reason.

  • Page 73: Hp Operating Systems And Virtualization Software Support For Proliant Servers

    For more information about version control tools, see the HP Systems Insight Manager User Guide, the HP Version Control Agent User Guide, and the HP Version Control Repository User Guide on the HP website (http://www.hp.com/go/hpsim). HP Operating Systems and Virtualization Software Support for ProLiant Servers For information about specific versions of a supported operating system, see the HP website (http://www.hp.com/go/ossupport).

  • Page 74: Troubleshooting

    Troubleshooting Troubleshooting resources The HP ProLiant Gen8 Troubleshooting Guide, Volume I: Troubleshooting provides procedures for resolving common problems and comprehensive courses of action for fault isolation and identification, issue resolution, and software maintenance on ProLiant servers and server blades. To view the guide, select a language: •...

  • Page 75: System Battery Replacement

    System battery replacement If the server no longer automatically displays the correct date and time, you might have to replace the battery that provides power to the real-time clock. Under normal use, battery life is 5 to 10 years. WARNING: The computer contains an internal lithium manganese dioxide, a vanadium pentoxide, or an alkaline battery pack.
  • Page 76 IMPORTANT: Replacing the system board battery resets the system ROM to its default configuration. After replacing the battery, reconfigure the system through RBSU. To replace the component, reverse the removal procedure. For more information about battery replacement or proper disposal, contact an authorized reseller or an authorized service provider.

  • Page 77: Regulatory Compliance Notices

    Regulatory compliance notices Regulatory compliance identification numbers For the purpose of regulatory compliance certifications and identification, this product has been assigned a unique regulatory model number. The regulatory model number can be found on the product nameplate label, along with all required approval markings and information. When requesting compliance information for this product, always refer to this regulatory model number.

  • Page 78: Declaration Of Conformity For Products Marked With The Fcc Logo, United States Only

    Modifications The FCC requires the user to be notified that any changes or modifications made to this device that are not expressly approved by Hewlett-Packard Company may void the user’s authority to operate the equipment. Cables Connections to this device must be made with shielded cables with metallic RFI/EMI connector hoods in order to maintain compliance with FCC Rules and Regulations.

  • Page 79: European Union Regulatory Notice

    CE and !). Please refer to the regulatory label provided on the product. The point of contact for regulatory matters is Hewlett-Packard GmbH, Dept./MS: HQ-TRE, Herrenberger Strasse 140, 71034 Boeblingen, GERMANY. Disposal of waste equipment by users in private...

  • Page 80: Japanese Notice

    This symbol on the product or on its packaging indicates that this product must not be disposed of with your other household waste. Instead, it is your responsibility to dispose of your waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic equipment.

  • Page 81: Chinese Notice

    Class B equipment Chinese notice Class A equipment Vietnam compliance marking notice This marking is for applicable products only. Ukraine notice Laser compliance This product may be provided with an optical storage device (that is, CD or DVD drive) and/or fiber optic transceiver.

  • Page 82: Battery Replacement Notice

    WARNING: Use of controls or adjustments or performance of procedures other than those specified herein or in the laser product's installation guide may result in hazardous radiation exposure. To reduce the risk of exposure to hazardous radiation: Do not try to open the module enclosure. There are no user-serviceable components inside. •...

  • Page 83: Acoustics Statement For Germany (Geräuschemission)

    Acoustics statement for Germany (Geräuschemission) Schalldruckpegel L < 70 dB(A) Zuschauerpositionen (bystander positions), Normaler Betrieb (normal operation) Nach ISO 7779:1999 (Typprüfung) Regulatory compliance notices 83...

  • Page 84: Electrostatic Discharge

    Electrostatic discharge Preventing electrostatic discharge To prevent damaging the system, be aware of the precautions you need to follow when setting up the system or handling parts. A discharge of static electricity from a finger or other conductor may damage system boards or other static-sensitive devices.

  • Page 85: Specifications

    Specifications Environmental specifications Specification Value Temperature range* 10°C to 35°C (50°F to 95°F) Operating -30°C to 60°C (-22°F to 140°F) Nonoperating Relative humidity (noncondensing) 10% to 90% Operating, maximum wet bulb temperature of 28°C (82.4°F) 5% to 95% Nonoperating, maximum wet bulb temperature of 38.7°C (101.7°F) * All temperature ratings shown are for sea level.

  • Page 86: Hp 460 W Cs Gold Hot-Plug Power Supply (92% Efficiency)

    Rated input current 430 W at 115 V Rated input power 430 W at 230 V — Power supply output Not less than 82% at 100% load Efficiency Not less than 85% at 50% load Not less than 82% at 20% load 400 W at 100 V to 120 V AC Maximum peak power input...

  • Page 87: Hot-Plug Power Supply Calculations

    Rated steady-state output power 460 W at 100 V to 120 V AC output 460 W at 200 V to 240 V AC output 460 W at 100 V to 120 V AC Maximum peak power output 460 W at 200 V to 240 V AC output Hot-plug power supply calculations For hot-plug power supply specifications and calculators to determine electrical and heat loading for the...

  • Page 88: Support And Other Resources

    Support and other resources Before you contact HP Be sure to have the following information available before you call HP: • Active Health System log Download and have available an Active Health System log for 3 days before the failure was detected. For more information, see the HP iLO 4 User Guide or HP Intelligent Provisioning User Guide on the HP website (http://www.hp.com/go/ilo/docs).
  • Page 89 providers or service partners) identifies that the repair can be accomplished by the use of a CSR part, HP will ship that part directly to you for replacement. There are two categories of CSR parts: • Mandatory—Parts for which customer self repair is mandatory. If you request HP to replace these parts, you will be charged for the travel and labor costs of this service.
  • Page 90 Pour plus d'informations sur le programme CSR de HP, contactez votre Mainteneur Agrée local. Pour plus d'informations sur ce programme en Amérique du Nord, consultez le site Web HP (http://www.hp.com/go/selfrepair). Riparazione da parte del cliente Per abbreviare i tempi di riparazione e garantire una maggiore flessibilità nella sostituzione di parti difettose, i prodotti HP sono realizzati con numerosi componenti che possono essere riparati direttamente dal cliente (CSR, Customer Self Repair).
  • Page 91 HINWEIS: Einige Teile sind nicht für Customer Self Repair ausgelegt. Um den Garantieanspruch des Kunden zu erfüllen, muss das Teil von einem HP Servicepartner ersetzt werden. Im illustrierten Teilekatalog sind diese Teile mit „No“ bzw. „Nein“ gekennzeichnet. CSR-Teile werden abhängig von der Verfügbarkeit und vom Lieferziel am folgenden Geschäftstag geliefert. Für bestimmte Standorte ist eine Lieferung am selben Tag oder innerhalb von vier Stunden gegen einen Aufpreis verfügbar.
  • Page 92 sustituciones que lleve a cabo el cliente, HP se hará cargo de todos los gastos de envío y devolución de componentes y escogerá la empresa de transporte que se utilice para dicho servicio. Para obtener más información acerca del programa de Reparaciones del propio cliente de HP, póngase en contacto con su proveedor de servicios local.
  • Page 93 Opcional – Peças cujo reparo feito pelo cliente é opcional. Essas peças também são projetadas para o reparo feito pelo cliente. No entanto, se desejar que a HP as substitua, pode haver ou não a cobrança de taxa adicional, dependendo do tipo de serviço de garantia destinado ao produto. OBSERVAÇÃO: Algumas peças da HP não são projetadas para o reparo feito pelo cliente.
  • Page 94 Support and other resources 94...
  • Page 95 Support and other resources 95...

  • Page 96: Acronyms And Abbreviations

    Acronyms and abbreviations ABEND abnormal end Array Configuration Utility Advanced Memory Protection Automatic Server Recovery baseboard management controller BSMI Bureau of Standards, Metrology and Inspection Conformité Européenne (European Conformity) Canadian Standards Association Customer Self Repair double data rate electromagnetic interference FBWC flash-backed write cache Acronyms and abbreviations 96...
  • Page 97 Federal Communications Commission HP CS HP Common Slot (power supply) HP SIM HP Systems Insight Manager HP SUM HP Smart Update Manager International Electrotechnical Commission Integrated Lights-Out Integrated Management Log International Organization for Standardization large form factor LRDIMM load reduced dual in-line memory module nonmaskable interrupt NVRAM nonvolatile memory...
  • Page 98 power distribution unit POST Power-On Self Test preboot execution environment RBSU ROM-Based Setup Utility RDIMM registered dual in-line memory module Rapid Deployment Pack radio frequency radio frequency interference redundant power supply serial attached SCSI SATA serial ATA Secure Digital small form factor HP Service Pack for ProLiant Acronyms and abbreviations 98...
  • Page 99 TMRA recommended ambient operating temperature Trusted Platform Module UDIMM unregistered dual in-line memory module unit identification universal serial bus Version Control Agent VCRM Version Control Repository Manager Acronyms and abbreviations 99...

  • Page 100: Documentation Feedback

    Documentation feedback HP is committed to providing documentation that meets your needs. To help us improve the documentation, send any errors, suggestions, or comments to Documentation Feedback (mailto:docsfeedback@hp.com). Include the document title and part number, version number, or the URL when submitting your feedback. Documentation feedback 100...

  • Page 101: Index

    Index controller 38 controller options 38 CSR (customer self repair) 88 access panel 19, 20 customer self repair (CSR) 88 Active Health System 62, 63 ACU (Array Configuration Utility) 62, 69 air baffle 20, 21 airflow requirements 24, 25 dedicated iLO management connector 49, 51 Array Configuration Utility (ACU) 69 diagnostic tools 62, 65, 71 ASR (Automatic Server Recovery) 71...
  • Page 102 front panel buttons 8 front panel components 7 memory 44, 45 front panel LEDs 8 memory options 32, 44 memory subsystem architecture 46 Mini-SAS cable 35 grounding methods 84 grounding requirements 26 NMI header 12 non-hot-plug drives, installing 33 hard drives, determining status of 13 hard drives, installing 32, 33 hardware options 28, 32 operating system installation 30...
  • Page 103 recommended ambient operating temperature temperature requirements 25 (TMRA) 25 TMRA (recommended ambient operating recovery key 53 temperature) 25 redundant ROM 71 Torx screwdriver 16 registering the server 31 TPM (Trusted Platform Module) 51, 53 TPM connector 10 regulatory compliance notices 77, 79 removing server from rack 18 troubleshooting 74 required information 88...

This manual is also suitable for:

Proliant dl320e gen8

Table of Contents