HP D7171A - NetServer - LPr Reference Card

HP NetServer LC 2000 & LC 2000r Technical Reference Card
A
Cabinet
Pedestal Version
6 PCI
Slots
System
Board
Release
Screws
(2 of 4)
System and
I/O Board
See C
Shelf 1: IDE CD-ROM Drive
Shelves 2 & 3: Optional
Mass Storage
See B
Shelf 4: Flexible Disk Drive
B

Mass Storage Device

Locations and Settings
Device Location in order
of recommendation
Standard Shelf 1
IDE CD-ROM
Standard Shelf 2
Hard Disk Drive
HP Accessory Hot-Swap HDD
9.1 GB HDD Slot 1, 2, 3, 4, 5, 6
6 Low-Profile,
HP Accessory
3 Half-Height Drives,
18.2 GB HDD
or
HP Accessory
mix LP/HH
36.4 GB HDD
Additional Shelf 3
SCSI device
Standard Dual Embedded
Channel SCSI
Controller
See documentation with each device for further
configuration information.
I/O Connectors
Rear of System Board
See C
Fan Fail
Fan Module
Hard Disk
Activity
Power
Indicator
Shevles
1 – 4
On/Off/Sleep
RESET
6
Hot-Swap HDD
5
4
Slots 1 – 6
3
Caution: Do not operate server for
2 See D
more than 2 minutes with any cover
1
(including Power Supply Bays and
(Front View) Disk Drives) removed. Processor will
shut down if overheated.
C
System and I/O Board
Device Settings
Set to
Master (Default)
SCSI ID 0 (Default)
For additional HDD,
CMOS
See D
Battery
I/0
For SureStore, Connectors
SCSI ID 2
For DAT, SCSI ID 4
SCSI ID 7
Rack Version
Front
Panel Display
Non-Hot-
Overtemperature
Swap Mass
Storage Cage
Power
Reserved
Secure
Mode
Power
RESET
Reset Keyboard
Lock
Flexible Disk
Drive SCSI A
PCI Slot 1
PCI Slot 2
32-bit
PCI Slot 3
PCI Slot 4
PCI Slot 5
64-bit
PCI Slot 6
*
Video
LAN
Keyboard
Mouse
Parallel
Serial
Connector
Management
Port
*
Secondary
VRM
Configuration
Primary VRM Primary Temperature Sensor (U51)
Switch
HP Product No. D8514-80201, REV B, Sept. 1999
Fan Assembly
Hot-Swap Mass
System Board
Storage Cage
Release Screw (1 of 4)
DIMM Slots
Processor
6
5
4
3
2
1
Knockout for
PCI Slots
External SCSI
See
SCSI B Front Panel Connector
System Board
*
Assembly
Release Screws (4)
IDE CD-ROM
Fan
Connector
Optional Redundant
Power Supply
3 Connectors
2
1
DIMM Slots
0
Power Connector
For Mass Storage
Power Supply
Connectors
Secondary Temperature Sensor (U43)
*
Primary
Secondary Processor Slot
Processor Slot
For additional information, see other side.
Default Boot Order
1. IDE CD-ROM
2. FDD
3. SCSI A Bus
• SCSI Device ID 0
• SCSI Device ID 9
4. SCSI B Bus
• SCSI Device ID 0
• SCSI Device ID 9
Optional
5. PCI Slot P1
Redundant
6. PCI Slot P2
Power Supply
7. PCI Slot P3
8. PCI Slot P4
9. PCI Slot P5
10. PCI Slot P6
I/O Connectors
See C
Power Connector
1
2
Power Supplies
(Rear View)
C
Configuration Switch
Switch 8 Off = 133MHz FSB
533 600 667 733
1
2 CPU
Speed
3
4
5
6
7
8
Test Only (7)
Password (6)
Clear Password
Config. Memory (5)
Clear Config. (CMOS)