建議您在處理電腦時使用防靜電的腕帶並站立在導電泡棉墊上。 拆開與裝回 HP TouchSmart PC 時,Hewlett-Packard 建議您使用尖端帶有磁性的螺絲起子,以更簡易 地拆卸與鎖回螺絲。 警告: 拆卸記憶體外蓋或背板時,請務必中斷 HP TouchSmart PC 與電源的連接。若沒有執行這些動作就拆開 HP TouchSmart PC 或進行任何程序,可能會導致人身傷害或裝備的損壞。 找出 HP TouchSmart PC 的組件 請參閱下列圖示找出 HP TouchSmart PC 的組件。 A:光碟機外蓋 D:電源變壓器接頭 G:接頭外蓋 B:背板 E:無線鍵盤和滑鼠接收器 C:電腦底座 F:記憶體外蓋 升級與維護手冊...
拆開 HP TouchSmart PC 為了避免人身傷害及設備損壞,在拆開 HP TouchSmart PC 之前,請務必依照順序完成下列步驟: 移除 HP TouchSmart PC 的所有媒體 (CD、DVD、記憶卡、USB 裝置以及外接式硬碟) 。 拔除任何與電腦連接的外接式裝置。 警告事項: 靜電會損壞 HP TouchSmart PC 或選購設備的電子組件。請碰觸一下接地金屬物體,確保您已釋放出 靜電。 ™ 點選 Windows Vista [ 開始 ] 按鈕 ,然後點選 [ 關機 ]。 警告: 為了降低電擊或觸及過熱表面等人身傷害的風險,請務必從牆上電源插座拔下電源線,並讓內部系統組 件先冷卻一下再觸碰。 系統完全關閉後,自...
Page 10
用您的手指伸進外蓋 (A) 左下角的間隔,然後輕拉拆卸接頭外蓋。 拔除所有連接在 HP TouchSmart PC 背部的連接線。 升級與維護手冊...
新增記憶體 您的 HP TouchSmart PC 中有隨機存取記憶體 (RAM),可以暫時儲存電腦上的資料和指令。HP TouchSmart PC 隨附一或兩個記憶體模組供您替換。 開始之前 請留意下列要求再進行拆卸與替換記憶體模組。 主機板含有 SO-DIMM (小型雙插入式記憶體模組)專用的插槽。下列圖示中圓圈位置即為記憶體模組配 對插槽。 若要判定您 HP TouchSmart PC 使用的記憶體模組之類型和速度,以及取得特定記憶體模組的資訊和規 格,請到:http://www.hp.com/support。 警告事項: 使用錯誤的記憶體模組類型可能會使電腦受損。 升級與維護手冊...
裝回 HP TouchSmart PC 為了避免人身傷害及設備損壞,在裝回 HP TouchSmart PC 之後,請務必依照順序完成下列步驟: 若先前已移除,請裝回電腦底座。將底座的四個螺絲孔對齊於電腦背部的四個孔上,然後裝回將底座 固定在電腦上的螺絲。 裝回記憶體外蓋。將記憶體外蓋對齊於電腦底座兩支架與螺絲孔的上方,並將外蓋推向底座進入定位 (A)。將記憶體外蓋下緣的兩邊往下壓,並卡進定位 (B)。按壓下緣的中間部份,確定所有的外蓋都已 推到底。 升級與維護手冊...
Page 34
Copyright Information The only warranties for Hewlett-Packard products and services are set forth in the express statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty. HP shall not be liable for technical or editorial errors or omissions contained herein.
Page 35
Table of Contents Safety Information ......................... 1 Before You Begin .......................... 1 Locating Components of the HP TouchSmart PC ................2 Opening the HP TouchSmart PC...................... 3 Adding Memory..........................7 Before you begin........................7 Removing a memory module...................... 8 Installing a memory module .....................10 Removing and Installing the Hard Disk Drive...................
Upgrading and Servicing Guide This guide provides instructions for upgrading the memory and the hard disk drive in your HP TouchSmart PC. Safety Information This product has not been evaluated for connection to an “IT” power system (an AC distribution system with no direct connection to the earth, according to IEC 60950).
It is recommended that you use an antistatic wrist strap and stand on a conductive foam pad when working on the computer. Hewlett-Packard recommends that you use a magnetic-tipped screwdriver when opening and closing the HP TouchSmart PC, to make it easier to remove and install the screws.
Opening the HP TouchSmart PC To avoid injury and equipment damage, always complete the following steps in order, when opening the HP TouchSmart PC: Remove any media (CD, DVD, memory cards, USB devices, and external hard disk drives) from the HP TouchSmart PC.
Page 40
Remove the connector cover by inserting your finger under the gap on the bottom-left side of the cover (A), and then pulling gently. Disconnect all other attached cables from the back of the HP TouchSmart PC. Upgrading and Servicing Guide...
Page 41
Place the computer face-down on a soft flat surface. HP recommends that you set down a blanket, towel, or other soft cloth (A) to protect the touch screen surface from scratches or other damage. Apply additional pressure to lift the computer stand as far as it will go to an upright position, about 90 degrees (B) from the computer, and then move the latch to the left until it is in the locked position (C).
Page 42
Remove the screw (A) that secures the memory cover to the back of the computer. Pull up the memory cover slightly on the bottom edge to release it (B), then, gently slide the cover down toward the bottom of the computer (C), and then remove it. WARNING: Beware of sharp edges inside the chassis.
Adding Memory Your HP TouchSmart PC comes with random access memory (RAM), which temporarily stores data and instructions on your computer. The HP TouchSmart PC ships with one or two memory modules that you can replace. Before you begin Observe the following requirements before removing and replacing the memory module. The motherboard contains sockets for SO-DIMMs (small outline dual in-line memory modules).
Removing a memory module Complete the procedures to prepare the HP TouchSmart PC. See “Opening the HP TouchSmart PC” on page 3. CAUTION: When handling a memory module, be careful not to touch any of the contacts. Doing so may damage the module. CAUTION: Do not pull the memory module out of the socket.
Page 45
Lift the memory module from the memory socket. Note the location of the key slot on the connector edge. Store the memory module in antistatic packaging. Upgrading and Servicing Guide...
Installing a memory module Upgrade the memory in your HP TouchSmart PC with memory of the same type and speed as the memory originally installed. The capacity for both memory modules must match for optimal performance. Both memory modules can be installed by using the same procedure listed below. CAUTION: When handling a memory module, be careful not to touch any of the contacts.
Page 47
Slide the memory module all the way into the memory slot, until the gold edge is almost completely hidden in the slot, and then push down the outer edge of the memory module until the retaining clips snap into place. CAUTION: The memory module must be inserted all the way into the slot before it is snapped down into place;...
Removing and Installing the Hard Disk Drive You can replace or upgrade the hard disk drive. The hard disk drive is a Serial ATA (advanced technology attachment) drive, which uses a narrow data cable. CAUTION: Before removing the hard disk drive, back up any personal files on the hard disk drive to an external storage device, such as a DVD.
Page 49
Remove the optical disc drive cover by lifting the bottom edge with your finger or a screwdriver, and then rotating the cover out and away from the computer. There are several tabs and two guide pins holding the cover in place, so be careful not to break the cover by applying too much force. Make sure the wireless keyboard and mouse receiver (A) has been removed.
Page 50
Lift the back cover up from the bottom inside edge of the memory cover area to release it, place both hands under the bottom edge of the cover and lift it up, and then rotate the back cover up as far as it will go.
Page 51
Remove the screw that secures the optical disc drive to the chassis, and then slide the drive toward the center of the computer to move it out of the way. You do not need to remove the optical drive cables. Remove the screw that secures the hard disk drive cage to the chassis.
Page 52
Slide the hard disk drive cage toward the top of the computer, and then pull it away from the computer. Disconnect the power and data cables by pressing the latches and then removing them from the drive. Upgrading and Servicing Guide...
Page 53
Remove the four screws that secure the hard disk drive to the cage, and then slide the hard disk drive out of the cage. Upgrading and Servicing Guide...
Installing a hard disk drive If necessary, remove the hard disk drive. See “Removing the hard disk drive” on page 12. Slide the hard disk drive into the cage, and then replace the four screws. Connect the power and data cables to the hard disk drive. Upgrading and Servicing Guide...
Page 55
Lower the hard disk drive cage straight down, align the four hooks on the cage with the four holes on the back of the chassis, and then slide the cage toward the bottom of the computer until it rests against the bracket on the chassis.
Page 56
Align the hooks on the optical disc drive with the holes on the computer, and then slide the optical disc drive toward the outer edge of the computer. Replace the screw that secures the optical disc drive to the chassis. Upgrading and Servicing Guide...
Page 57
Replace the back cover. Align the hooks at the top edge of the back cover with the holes on the top of the computer. The screw holes on the back cover should be aligned with the screw holes on the back of the computer.
Page 58
Replace the nine screws that secure the back cover to the computer. Four of the screws are located along the bottom edge of the back cover, two are located on the sides of the optical drive, and three are located in the connector area. CAUTION: You must replace the screws on each side of the optical disc drive to ensure that the drive slot is aligned properly with the back cover.
Closing the HP TouchSmart PC To avoid injury and equipment damage, always complete the following steps in order, after closing the HP TouchSmart PC: If you removed it, replace the computer stand. Align the four screw holes of the stand over the four holes on the back of the computer, and then replace the four screws that secure the stand to the computer.
Page 60
Replace the screw that secures the memory cover to the computer. Push the computer stand back slightly beyond the locked position (A), holding it with one hand so it does not snap back when the lock is released, and then release the lock on the computer stand (B) with the other hand.
Page 61
Replace the keyboard and mouse receiver. Place the computer upright on a flat surface with the stand in a safe and open position. 10° min. 40°max Upgrading and Servicing Guide...
Page 62
Attach the power adapter to the back of the computer and then reconnect the power cord to the power source. WARNING: To reduce the risk of electrical shock, fire, or equipment damage, do not plug telecommunications or telephone cables into the network interface card (NIC) (labeled as LAN). Reconnect all other cables, and then replace the connector cover by aligning the three tabs on the side edge of the cover with the holes on the computer, and then rotating inward to snap it into place.