Dram Configuration - Gigabyte GA-990XA-UD3 User Manual

DRAM Configuration

CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
CPU Host Clock Control
x CPU Frequency(MHz)
Set Memory Clock
x Memory Clock
DCTs Mode
DDR3 Timing Items
x 1T/2T Command Timing
x CAS# latency
x RAS to CAS R/W Delay
x Row Precharge Time
x Minimum RAS Active Time
x TwTr Command Delay
x Trfc0 for DIMM1, DIMM3
x Trfc1 for DIMM2, DIMM4
x Write Recovery Time
x Precharge Time
x Row Cycle Time
x RAS to RAS Delay
** DCTs Drive Strength **
higf: Move Enter: Select
F5: Previous Values
CMOS Setup Utility-Copyright (C) 1984-2011 Award Software
ProcOdt(ohms)
DQS Drive Strength
Data Drive Strength
MEMCLK Drive Strength
Addr/Cmd Drive Strength
CS/ODT Drive Strength
CKE Drive Strength
** DCTs Addr/Cmd Timing **
Addr/Cmd Setup Time
Addr/Cmd Fine Delay
CS/ODT Setup Time
CS/ODT Fine Delay
CKE Setup Time
CKE Fine Delay
Channel interleaving
Bank Interleaving
DQS Training Control
CKE Power Down Mode
Memclock tri-stating
higf: Move Enter: Select
F5: Previous Values
CPU Host Clock Control, CPU Frequency (MHz), Set Memory Clock, Memory Clock
The settings under the four items above are synchronous to those under the same items on the MB In-
telligent Tweaker(M.I.T.) main menu.
DCTs Mode
Allows you to set memory control mode.
Ganged Sets memory control mode to single dual-channel.
Unganged Sets memory control mode to two single-channel. (Default)
DDR3 Timing Items
Manual allows all DDR3 Timing items below to be configurable.
Options are: Auto (default), Manual.
DRAM Configuration
[Auto]
200
[Auto]
x6.66 1333Mhz
[Unganged]
[Auto] SPD Auto
Auto --
Auto 9T
Auto 9T
Auto 9T
Auto 24T 24T
Auto 5T
Auto 110ns 110ns
Auto --
Auto 10T 10T
Auto 5T 5T
Auto 33T 33T
Auto 4T 4T
DCT0 DCT1
+/-/PU/PD: Value F10: Save
F6: Fail-Safe Defaults
DRAM Configuration
[Auto] 60 [Auto] 240
[Auto] 1.0x [Auto] 1.5x
[Auto] 1.0x [Auto] 1.5x
[Auto] 1.5x [Auto] 1.5x
[Auto] 1.5x [Auto] 2.0x
[Auto] 1.5x [Auto] 2.0x
[Auto] 1.5x [Auto] 2.0x
DCT0 DCT1
[Auto] 1/2T [Auto] 1/2T
[Auto] 0/64 [Auto] 0/64
[Auto] 1/2T [Auto] 1/2T
[Auto] 0/64 [Auto] 0/64
[Auto] 1/2T [Auto] 1/2T
[Auto] 0/64 [Auto] 0/64
[Enabled]
[Enabled]
[Skip DQS]
[Disabled]
[Disabled]
+/-/PU/PD: Value F10: Save
F6: Fail-Safe Defaults
- 37 -
Item Help
Menu Level 
--
9T
9T
9T
5T
--
ESC: Exit F1: General Help
F7: Optimized Defaults
Item Help
Menu Level 
ESC: Exit F1: General Help
F7: Optimized Defaults
BIOS Setup