GE PVB98STSS Installation Instructions Manual
Downdraft vent systems
Hide thumbs
Also See for PVB98STSS:
- Owner's manual (20 pages) ,
- Installation instructions manual (16 pages) ,
- Dimensions and installation information (3 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
Owner's Manual
Advertisement
Table of Contents
Related Manuals for GE PVB98STSS
Summary of Contents for GE PVB98STSS
- Page 1 Installation Instructions Downdraft Vent Systems PVB94 PVB98 ZVB30 ZVB36...
-
Page 2: Safety Information
Safety Information BEFORE YOU BEGIN WARNING: TO REDUCE THE RISK Read these instructions completely and carefully. OF FIRE, ELECTRIC SHOCK OR INJURY TO PERSONS, IMPORTANT OBSERVE THE FOLLOWING. A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the IMPORTANT –... - Page 3 Design Information CONTENTS Design Information Ductwork ..............3 ................10 ..................3 Installation Instructions ............... 4, 5 ......... 11 Installation Preparation ..........11 ................6, 7 ........................7 ............13 Tools and Materials Required ..........7 ......13 ..............7 ..................13 ................8 Venting Options .................9 PRODUCT DIMENSIONS 30"...
-
Page 4: Advance Planning
Downdraft Vent and Cooktop Cutout The installation of these downdraft vents with any GE Before you begin, review the combination cutout burner box, the vent and the cutout clearance from illustrations on page 6. - Page 5 Design Information Electrical and Gas Locations Clearances Plan the placement of the electrical outlet and gas of the cabinet because it may interfere with the for information on location of electrical and gas connections. remote locations. instruction for appropriate clearances. long power cord.
-
Page 6: Installation Preparation
Installation Preparation CUTOUTS AND CLEARANCES bottom to ensure it meets the minimum width requirements . rear and front cuts are exactly perpendicular to the front edge of the countertop. “A” guide. Width “A” Creative Solutions Width Cooktop Cooktop 4-1/2” Max MODEL “A”... - Page 7 Installation Preparation 36" COOKTOP AND DOWNDRAFT COMBINATION IMPORTANT: The countertop cutout depth requires minimum total countertop depth. 36" NOTE: Before you begin, measure and mark depth is available. top behind cutout required 34" and downdraft combination installation. NOTE: PARTS SUPPLIED TOOLS AND MATERIALS REQUIRED REMOVE PACKAGING set carton aside.
- Page 8 (Please read carefully.) cord. The power cord of this appliance is equipped with Gas Cooktops If this vent is installed in combination with a GE or same duplex outlet. customer should have the wall receptacle and Electric Cooktops sure the receptacle is properly grounded and has If this vent is installed in combination with a GE correct polarity.
- Page 9 Installation Preparation VENTING OPTIONS discharge outlet pointing straight down and can be changed to the left or right side. and can be transitioned to 6" round. Side-to-Side Adjustments: The entire blower mounting plate can be will help to align vent discharge to house Discharge Direction IMPORTANT: The blower assembly may be removed and turned...
-
Page 10: Duct Fittings
Visit GEAppliances.com for round transition 6" round wall cap wall cap 6" round roof cap 33 ft. equivalent. Equivalent length of duct pieces is based on actual tests conducted by GE Evaluation Engineering... -
Page 11: Installation Instructions
Installation Instructions 1 INSTALL DOWNDRAFT VENT each side of the downdraft vent. For right-side or straight-down blower discharge, For left-side blower discharge, fasten the Level Level Brackets 4 to 5” 4 to 5” should be a 1/8” minimum gap between the Bottom Brackets 2 INSTALL DUCTWORK... - Page 12 Installation Instructions 3 INSTALL REMOTE SWITCH WARNING: SHOCK HAZARD Connect Remote Switch to Remote Harness hole and attach the harness connector to the result in personal injury or damage to the electrical remote connector. controls. WARNING: BURN HAZARD foam piece and mount the remote switch on the The remote switch must be located so that it can be countertop such that the switch connectors stay to do so may result in ignition of clothing which could...
- Page 13 Installation Instructions 4 CONNECT POWER Plug power cord into properly grounded receptacle. 5 INSTALL FILTERS, CHECK OPERATION to raise the vent. straight up and pull forward. Retainers NOTE: before lowering the vent. The fan will automatically automatically come on at the previously set speed when the vent is fully raised.
- Page 14 Notes...
- Page 15 Notes...
- Page 16 NOTE: safety glasses or goggles should be worn. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, materials, appearance...