Category — Lo-Fi; Category — Tec - Yamaha MX49 Data List

[3] VCM PEDAL WAH
No. Parameter
1 Pedal Control 0 – 127
2 Bottom 0 – 127
3 Top 0 – 127
4 Resonance Offset -12.0 – +12.0
5 Direction Up, Down
6 Type High, Mid, Low, Bass
7 Overdrive 0.0dB – +40.0dB
8 Output -20.0dB – +10.0dB
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
When the value of Bottom is greater than Top, the sound will not be modulated and only the Bottom
value is available.
Category — Lo-Fi
[1] NOISY
No. Parameter
1 Mod Depth 0 – 10
2 Mod Speed 0 – 127
3 Mod Feedback -63 – +63
4 Mod Mix Balance 1 – 127
5 Drive 0 – 127
6 AM Speed 0.00Hz – 39.7Hz
7 AM Depth 0 – 127
8 LPF Cutoff Frequency 1.0kHz – 20.0kHz
9 LPF Resonance 1.0 – 12.0
10 Dry/Wet Balance D63>W – D=W – D<W63
11 EQ Frequency 100Hz – 10.0kHz
12 EQ Gain -12dB – +12dB
13 EQ Width 1.0 – 12.0
14 —
15 —
16 —
[2] DIGITAL TURNTABLE
No. Parameter
1 Click Density 0 – 5
2 Click Level 0 – 127
3 Noise Tone 0 – 6
4 Noise Mod Speed 0.00Hz – 39.7Hz
5 Noise Mod Depth 0 – 127
6 Dry Send to Noise 0 – 127
7 Noise LPF Cutoff Frequency 1.0kHz – 20.0kHz
8 Noise LPF Q 1.0 – 12.0
9 Noise Level 0 – 127
10 —
11 Dry Level 0 – 127
12 Dry LPF Cutoff Frequency 1.0kHz – 20.0kHz
13 —
14 —
15 —
16 —
Range Value Table No.
(0 – 127)
(0 – 127)
(0 – 127)
(40 – 88)
(0 – 1)
(0 – 3)
(0 – 80)
(24 – 84)
Range Value Table No.
(0 – 10)
(0 – 127)
(1 – 127)
(1 – 127)
(0 – 127)
(0 – 127) 1
(0 – 127)
(34 – 60) 3
(10 – 120)
(1 – 127)
(14 – 54) 3
(52 – 76)
(10 – 120)
Range Value Table No.
(0 – 5)
(0 – 127)
(0 – 6)
(0 – 127) 1
(0 – 127)
(0 – 127)
(34 – 60) 3
(10 – 120)
(0 – 127)
(0 – 127)
(34 – 60) 3
Category — TEC
[1] RING MODULATOR
No. Parameter
1 OSC Frequency Coarse 0.5Hz – 5kHz
2 OSC Frequency Fine 0 – 127
3 LFO Wave Triangle, Sine
4 LFO Depth 0 – 127
5 LFO Speed 0.0Hz – 39.70Hz
6 HPF Cutoff Frequency 20Hz – 8.0kHz
7 LPF Cutoff Frequency 1.0kHz – 20.0kHz
8 —
9 —
10 Dry/Wet Balance D63>W – D=W – D<W63
11 —
12 —
13 – 16: Same as the parameters shaded in gray in CROSS DELAY on page 33.
[2] AUTO SYNTH
No. Parameter
1 Mod Speed 0 – 127
2 Mod Wave Type Type A, Type B, Type C,
Type D
3 Mod Depth 0 – 127
4 Mod Depth Ofst R -63 – +63
5 HPF Cutoff Frequency 20Hz – 8.0kHz
6 LPF Cutoff Frequency 1.0kHz – 20.0kHz
7 Delay Time 0.1ms – 370.0ms
8 Delay Time Ofst R 0 – 884
9 Delay Level 0 – 127
10 Dry Mix Level 0 – 127
11 Feedback Level -63 – +63
12 FB Level Ofst R -63 – +63
13 AM Speed 0.00Hz – 39.7Hz
14 AM Wave Triangle, Sine, Saw Up, Saw
Down
15 AM Depth 0 – 127
16 AM Inverse R Normal, Inverse
[3] ISOLATOR
No. Parameter
1 On/off Switch On, Off
2 Low Level -64 – +63
3 Mid Level -64 – +63
4 High Level -64 – +63
5 Low Mute Off, On
6 Mid Mute Off, On
7 High Mute Off, On
8 —
9 —
10 —
11 —
12 —
13 —
14 —
15 —
16 —
[4] TECH MODULATION
No. Parameter
1 Mod Speed 0 – 127
2 Mod Depth 0 – 127
3 Mod Gain -12 – +12dB
4 Mod Mix Balance D63>W – D=W – D<W63
5 Pre Mod HPF Cutoff 20Hz – 8.0kHz
Frequency
6 Mod LPF Cutoff Frequency 1.0kHz – 20.0kHz
7 Mod LPF Resonance 1.0 – 12.0
8 Delay Time 0.1 – 740.0ms
9 Delay Time Ofst R 0 – 884
10 Dry/Wet Balance D63>W – D=W – D<W63
11 Feedback Level -63 – +63
12 FB Level Ofst R -63 – +63
13 Feedback High Damp 0.1 – 1.0
14 FB Hi Damp Ofst R -0.9 – +0.9
15 —
16 —
Effect Parameter List
Range Value Table No.
(0 – 127) 14
(0 – 127)
(0 – 1)
(0 – 127)
(0 – 127) 1
(0 – 52) 3
(34 – 60) 3
(1 – 127)
Range Value Table No.
(0 – 127)
(0 – 3)
(0 – 127)
(1 – 127)
(0 – 52) 3
(34 – 60) 3
(1 – 3700)
(0 – 884)
(0 – 127)
(0 – 127)
(1 – 127)
(1 – 127)
(0 – 127) 1
(0 – 3)
(0 – 127)
(0 – 1)
Range Value Table No.
(0 – 1)
(0 – 127)
(0 – 127)
(0 – 127)
(0 – 1)
(0 – 1)
(0 – 1)
Range Value Table No.
(0 – 127)
(0 – 127)
(52 – 76)
(1 – 127)
(0 – 52) 3
(34 – 60) 3
(10 – 120)
(1 – 7400)
(0 – 884)
(1 – 127)
(1 – 127)
(1 – 127)
(1 – 10)
(1 – 19)
MX49/MX61 Data List
38