Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Hunter 23721
Summary of Contents for Hunter 23721
- Page 1 41893-01 • 08/29/05...
-
Page 2: Table Of Contents
6 • Assembling the Blades .........9 • To reduce the risk of fire, electrical shock, or motor damage, do not 7 • Installing the Switch Housing....10 use a solid-state speed control with this fan. Use only Hunter speed 8 • Operating and Cleaning controls. - Page 3 Understanding Mounting and Installer’ s Choice® Hunter’s patented 3-position mounting system provides you maximum installation fl exibility and ease. You can install your Hunter fan in one of three ways, depending on ceiling height and your preference: Low Profi le, Standard, or Angle mounting. e steps in this manual include instructions for all three Installer’s Choice mounting methods.
-
Page 4: Getting Ready
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •... -
Page 5: Installing The Ceiling Plate
Do not over tighten. Steps 2-3 – 2-5 Flat Washer 3” Screw For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows printed on the ceiling plate are pointing towards the ceiling peak. 41893-01 • 08/29/05 Hunter Fan Company... -
Page 6: Assembling And Hanging The Fan
3-5. Raise the fan and place the hook on the ceiling plate through the U-shaped hole in the rim. Go to 4 • Wiring the Fan. WARNING: Fan may fall if not assembled as directed in these installation instructions. Step 3-5 U-shaped #8-32 x 1” Screw Hole Hunter Fan Company 41893-01 • 08/29/05... -
Page 7: Wiring The Fan
CAUTION: Be sure no bare wire or wire strands are visible after making connections. 4-6. Push all wires and wire nuts back through the ceiling plate hole into the outlet box. Wire Nut Step 4-4 41893-01 • 08/29/05 Hunter Fan Company... -
Page 8: Installing The Canopy And Canopy Trim Ring
2. Press fi rmly on opposite sides of the ring towards the canopy. e tabs will fl ex out releasing the trim ring from the canopy Step 5-3 Steps 5-4 – 5-5 Canopy Screw Hunter Fan Company 41893-01 • 08/29/05... -
Page 9: Assembling The Blades
6 • Assembling the Blades Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades. -
Page 10: Installing The Switch Housing
Attach the Clearance Hole lower switch housing to the upper switch housing with two #8-32 Plug Connector x 3/8” housing assembly screws. Locator Post Steps 7-6 – 7-7 Hunter Fan Company 41893-01 • 08/29/05... -
Page 11: Operating And Cleaning Your Ceiling Fan
To Change Airfl ow Direction Turn the fan off and let it come to a complete stop. Slide the reversing switch on the fan to the opposite position. Restart fan. Reversing Switch 41893-01 • 08/29/05 Hunter Fan Company... -
Page 12: Troubleshooting
3. Turn power off , support fan very carefully, and check that the hanger ball is properly seated. If you need parts or service assistance, please call 888-830-1326 or visit us at our Web site at http://www.hunterfan.com. Hunter Fan Company 2500 Frisco Avenue Memphis, Tennessee 38114 Hunter Fan Company 41893-01 • 08/29/05...