Frigidaire FPHD2481KF - Professional 24" -Built Service Data Sheet page 2

Operation
To start
Close and latch door. Press START/CANCEL pad.
To delay start Close and latch door. Press DELAY START pad to
select desired delay time.
To select a new
Press desired cycle and/or option pad. The indicator
cycle or option
lights will change. Press START/CANCEL within 15
seconds to begin cycle.
To cancel cycle Press START/CANCEL. Dishwasher will drain for
90 seconds, then shut off.
For controls
lock . . . . . . . . . . . Press and hold the RINSE ONLY or AIR DRY
pad for 3 seconds. To unlock, press and hold the
RINSE ONLY or AIR DRY pad for 3 seconds.
Water/Service Test
To activate Water/Service Test
place unit in Power Failure or
Idle Mode and then press two
pads simultaneously for 3 seconds.
For Professional Series units press
DRY and START/CANCEL.
For Gallery Series units press
SANITIZE and START/CANCEL.
1 FILL/DISPENSER
2 FILL
The dishwasher will then step
3 WASH/HEAT
through the test cycle per the chart.
4 PAUSE
Pushing the START/CANCEL pad
5 WASH/HEAT
will advance the dishwasher to the
6 WASH/HEAT/DISP.
next step.
7
DRAIN
8 DRY
TOTAL
Display Codes (Readout)
SENSING
or LO..Low liquid in the rinse aid dispenser
WASHING
PF ..........A power failure has occurred
SANITIZED
HO or Hd .........Water heating delay
DRYING
CL ..........Close and latch the door CLEAN
OPTION LED's Flashing
ER/ER....Switch Failure
ER/CE....Configuration Error
STATUS LED's Flashing
ER/uo.....Vent will not close RINSE AGENT LOW ------- The liquid rinse agent is low. Light will switch off after 5 complete wash cycles or dispenser is
(Some models)
ER/uF.....Fan not running
'01-24' ....Hour(s) delay before start
(Some models)
60 1 0 0 0 1 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Fan damper Uo
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 Turbidity
27 0 1 1 0 0 0 Tu
45 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 1 0 1 0 0 1 1 0 0 0 Hall sensor HS HS
0.4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 0 0 1 0 0 1 1 0 0 0
75 0 1 0 1 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
0 1 0 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
60 0 0 0 0 0 0 Thermistor Th
1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
90 0 0 1 0 0 0 0 0 0 0 Fan speed Fan speed UF
90 0 0 1 X 0 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
0 0 0 Rinse aid RA
447 0 0 1 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
X - denotes selectable option
CLEAN LED stays on until door is opened or cycle is started.
Cycle Selection Options
Display Codes (LED)
----------------------Turbidity sensor is checking the condition of the wash/rinse water.
No sensing for LIGHT WASH (UPPER RACK), LIGHT WASH (LOWER RACK) and CHINA/CRYSTAL.
----------------------Wash portion of cycle.
--------------------The SANITIZED criteria has been met. Indicator light will switch off when door is opened.
------------------------ Drying portion of cycle.
------------------------ Shows completion of cycle. Indicator light will switch off when door is opened.
-- HI-TEMP WASH and NO HEAT DRY/POWER DRY OFF LED's flashing indicates power failure has
occurred. Press START/CANCEL pad and reselect desired options and cycle.
-- The STATUS LED's that are lit when the door is opened will flash. Close door.
filled.
Wiring Diagram
Color Code
BK.......................... Black
Y-BK.............Yellow/Black
BU............................Blue
PK............................Pink
R...............................Red
R-BK...............Red/Black
W............................White
TURBIDITY SENSOR/
THERMISTOR