Realtime Messages - Yamaha S08 Data List

2.2.2.4 Normal Voice bulk dump
This message sets the NORMAL VOICE block (refer to tables <2-1>, <2-2>, <2-9>,
<2-10>).
To receive this message, the Bulk Header and Bulk Footer of Bulk Control must be
received before and after reception, respectively.
The Bulk Header determines the Memory Bank/Voice number to which the data is stored.
2.2.2.5 Drum Voice bulk dump
This message sets the NORMAL VOICE block (refer to tables <2-1>, <2-2>, <2-11>,
<2-12>).
To receive this message, the Bulk Header and Bulk Footer of Bulk Control must be
received before and after reception, respectively.
The Bulk Header determines the Memory Bank/Voice number to which the data is stored.
2.3 Parameter request
This message requests transmission of a parameter value.
The output is transmitted in the Parameter Change message format (refer to 2.1.x).
2.3.1 XG parameter request
This message requests transmission of XG parameter settings.
Settings are transmitted in the format of an XG parameter change (refer to 2.1.3).
11110000 F0H
01000011 43H
0001nnnn 3NH
01001100 4CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
11110111 F7H
2.3.2 S08 native parameter request
This message requests transmission of a parameter value unique to the S08.
The output is transmitted in the format of a S08 native parameter change (refer to 2.1.4).
11110000 F0H
01000011 43H
0001nnnn 3NH
01101100 6CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
11110111 F7H
2.4 Dump request
This message requests transmission of a specific block of parameter values.
The output is the same as the bulk dump format.
2.4.1 XG dump request
This message requests transmission of all parameters of the specified block of XG
parameters.
The output is the same as the format of XG bulk dump (refer to 2.2.1).
11110000 F0H
01000011 43H
0001nnnn 2NH
01001100 4CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
11110111 F7H
Address is valid only when the beginning of the block has been specified.
2.4.2 S08 native dump request
This message requests transmission of all parameters of the specified block of S08 native
parameters.
The output is in the same format as an S08 native bulk dump (refer to 2.2.2).
11110000 F0H
01000011 43H
0001nnnn 2NH
01101100 6CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
11110111 F7H
Address is valid only when the beginning of the block has been specified.
No System Exclusive Message is received when the Compare function is active.
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
End of Exclusive
3.

Realtime messages

3.1 Active sensing
a) Transmission
Transmitted at every 270 msec.
b) Receive
Once FE has been received, failure to receive any MIDI message for an interval longer
than approximately 300 msec will cause processing to be performed as if ALL SOUND
OFF, ALL NOTE OFF, and RESET ALL CONTROLLERS messages were received, and
the unit will reset to a condition in which FE was never received.
3.2 Timing Clock
Status: F8H
3.3 Start
Status: FAH
3.4 Continue
Status: FBH
3.5 Stop
Status: FCH
24