Yamaha S08 Data List page 23

2.1.3.1 XG System On
11110000 F0H
01000011 43H
0001nnnn 1NH
01001100 4CH
00000000 00H
00000000 00H
01111110 7EH
00000000 00H
11110111 F7H
2.1.3.2 XG System parameter change
This message sets the XG SYSTEM block (refer to tables <1-1>, <1-2>).
2.1.3.3 Multi Effect1 parameter change
This message sets the MULTI EFFECT1 block (refer to tables <1-1>, <1-4>).
The S08 responds to this message only when it is set to the Multi mode.
2.1.3.4 Multi Part parameter change
This message sets the MULTI PART block (refer to tables <1-1>, <1-5>).
The S08 responds to this message only when it is set to the Multi mode.
2.1.3.5 Drums Setup parameter change
This message sets the DRUMS SETUP block (refer to tables <1-1>, <1-6>).
The S08 responds to this message only when it is set to the Multi mode.
2.1.4 S08 native parameter change
This message sets parameters unique to the S08. Each message sets a single parameter.
Each message modifies a single parameter.
The message format is as follows.
11110000 F0H
01000011 43H
0001nnnn 1NH
01101100 6CH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
0sssssss SSH
: :
11110111 F7H
For parameters whose Data Size is 2 or 4, the number of data bytes indicated by Size are
transmitted.
2.1.4.1 Native System parameter change
This message sets the NATIVE SYSTEM block (refer to tables <2-1>, <2-3>).
2.1.4.2 Remote Switch parameter change
This message sets the REMOTE SWITCH block (refer to tables <2-1>, <2-5>).
2.1.4.3 Normal Voice parameter change
This message sets the NORMAL VOICE (Edit Buffer) block (refer to tables <2-1>, <2-9>,
<2-10>).
The S08 responds to this message only when it is set to the Voice mode.
2.1.4.4 Drum Voice parameter change
This message sets the DRUM VOICE (Edit Buffer) block (refer to tables <2-1>, <2-11>,
<2-12>).
The S08 responds to this message only when it is set to the Voice mode.
2.1.5 Other parameter changes
2.1.5.1 Master tuning
This message simultaneously modifies the tuning of all channels.
11110000 F0H
01000011 43H
0001nnnn 1NH
00100111 27H
00110000 30H
00000000 00H
00000000 00H
0000mmmm 0MH
0000llll 0LH
0xxxxxxx XXH
11110111 F7H
Normally, the XG SYSTEM message MASTER TUNE should be used (refer to table
<1-2>).
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
Data
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Address High
Address Mid
Address Low
Master Tune MSB
Master Tune LSB
ignored
End of Exclusive
2.2 Bulk dump
This device uses the following bulk dump messages.
[XG BULK DUMP]
1) XG System bulk dump
2) System Information bulk dump
3) Multi Effect1 bulk dump
4) Multi Part bulk dump
5) Drums Setup bulk dump
[NATIVE BULK DUMP]
1) Native System bulk dump
2) Bulk Control bulk dump
3) Native Multi bulk dump
4) Normal Voice bulk dump
5) Drum Voice bulk dump
2.2.1 XG bulk dump
This message sets XG-related parameters. Unlike parameter change messages, a single
message can modify multiple parameters. The message format is as follows.
11110000 F0H
01000011 43H
0000nnnn 0NH
01001100 4CH
0sssssss SSH
0ttttttt TTH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
0vvvvvvv VVH
: :
0kkkkkkk KKH
11110111 F7H
Address and Byte Count are given in tables 1-n. Byte Count is indicated by the total size of
the Data in tables 1-n.
Bulk dump and dump request messages are received when the beginning of the block is
specified as the 'Address'.
'Block' indicates the unit of the data string that is indicated in tables 1-n as 'Total size'.
Check sum is the value that produces a lower 7 bits of 0 when the Start Address, Byte
Count, Data, and the Check-sum itself are added.
2.2.1.1 XG System bulk dump
This message sets the XG SYSTEM block (refer to tables <1-1>, <1-2>).
2.2.1.2 System Information bulk dump
This message indicates the contents of the SYSTEM INFORMATION block (refer to tables
<1-1>, <1-3>).
This message is transmitted in response to a Dump Request, but this message will be
ignored if it is received.
2.2.1.3 Multi Effect1 bulk dump
This message sets the MULTI EFFECT1 block (refer to tables <1-1>, <1-4>).
2.2.1.4 Multi Part bulk dump
This message sets the MULTI PART block (refer to tables <1-1>, <1-5>).
2.2.1.5 Drums Setup bulk dump
This message sets the DRUMS SETUP block (refer to tables <1-1>, <1-6>).
2.2.2 S08 native bulk dump
This message modifies parameters unique to the S08. Unlike parameter change
messages, a single message will modify multiple parameters.
The message format is as follows.
11110000 F0H
01000011 43H
0000nnnn 0NH
01101100 6CH
0sssssss SSH
0ttttttt TTH
0ggggggg GGH
0mmmmmmm MMH
0lllllll LLH
0vvvvvvv VVH
: :
0kkkkkkk KKH
11110111 F7H
Address and Byte Count are given in tables x-n. Byte Count is indicated by the total size of
the Data in tables x-n.
Bulk dump and dump request messages are received when the beginning of the block is
specified as the 'Address'.
Block indicates the unit of the data string that is indicated in tables x-n as 'Total size'.
Check sum is the value that produces a lower 7 bits of 0 when the Start Address, Byte
Count, Data, and the Check-sum itself are added.
2.2.2.1 Native System bulk dump
This message sets the NATIVE SYSTEM block (refer to tables <2-1>, <2-2>, <2-3>).
2.2.2.2 Bulk Control bulk dump
Bulk Control bulk dump This message sets the parameters such as Multi Number, Memory
Bank and Voice Number when the Native Multi bulk dump, Normal Voice bulk dump or
Drum Voice Bulk dump is received (refer to tables <2-1>, <2-2>, <2-4>).
2.2.2.3 Native Multi bulk dump
This message sets the NATIVE MULTI block (refer to tables <2-1>, <2-2>, <2-6>, <2-7>,
<2-8>).
To receive this message, the Bulk Header and Bulk Footer of Bulk Control must be
received before and after reception, respectively.
The Bulk Header determines the Multi number to which the data is stored.
23
Exclusive status
YAMAHA ID
N:Device Number
Model ID
ByteCountMSB
ByteCountLSB
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive
Exclusive status
YAMAHA ID
N:Device Number
Model ID
Byte Count MSB
Byte Count LSB
Address High
Address Mid
Address Low
Data
Check-sum
End of Exclusive