IMPORTANT SAFETY Before applying power INSTRUCTIONS Caution : Read this page carefully to ensure safe operation. Caution : Read this page carefully to Units are designed for operation as follows. ensure safe operation. Australia ............AC 240 V only Read Instructions – All the safety and operating Europe ..............
Page 3
14. Replacement Parts – When replacement parts 6. Power Sources – This product should be operated are required, be sure the service technician has used only from the type of power source indicated on the replacement parts specified by the manufacturer product.
If any accessories are missing, or if the unit is damaged or fails to operate, notify your dealer immediately. If the unit was shipped to you directly, notify your shipper immediately. Kenwood recommends that you retain the original carton and packing materials in case you need to move or ship the unit in the future.
Installation Installation for main amplifier C-AX7 (AX-7 system) M-AX7 (AX-7 system) M-AX700 LS-AXD7 (AX-7 system) LS-AXD7 (AX-7 system) Left speaker Right speaker CAUTION Be sure to adhere to the following, or proper ventilation will be blocked causing damage or fire hazard. ¶...
Installation Installation for speakers ¶ In such case, turn on the TV and check that color reproduction is normal. If color is distorted, You can enjoy 5.1ch surround reproduction by turn the TV off for 15 to 30 minutes, then turn it connecting this 3.1ch speaker system with the AX-7 back on and check again.
Be sure to follow the procedure given here when carrying out installation. Kenwood can assume no liability for injury or damage that may occur if a speaker setup falls from the wall as a result of incorrect installation or insufficient support strength.
Connections Connect every connection cord firmly. Incomplete insertion may cause loss of audio output or generation of noise. Caution for connection Do not plug the power cord into the power outlet until all other connections are completed. Before unplugging a connected cord or cable, be sure to set the power key to OFF and unplug the power cord from the power outlet in advance.
Page 9
C-AX7 (AX-7 system) WOOFER WOOFER DIGITAL OUT CENTER PCM / BIT STREAM OPTICAL ROOM EQ FRONT SURROUND 1 MIC IN TAPE VIDEO 1 VIDEO 2 PRE OUT CENTER AUDIO S VIDEO VIDEO LS-AXD7 (AX-7 system) ANTENNA Left speaker VIDEO OUT SYSTEM CONTROL M-AX7 (AX-7 system)
Names and functions of parts 1 2 3 1 Power key 4 CHANNEL SELECTOR key Used for setting the unit to On or Standby. Used for switching the amplifier between 4 channels (25 W x 4) and 2 channels (50 W x 2). •...
Speaker setting For an even better surround effect it is necessary to System selection match the speaker distances and volumes correctly. At the time of speaker setting, the difference in the speaker distances can be compensated by adjusting the volume for each speaker and the sound delay time.
Speaker setting Setting the volume balance Setting the speaker distance MULTI CONTORL MULTI CONTORL ENTER ENTER SP SETUP SP SETUP 1 Press the [SP SETUP] key on the remote 1 Press the [SP SETUP] key on the remote control of AX-7, press the MULTI CONTROL control of AX-7, press the MULTI CONTROL [ @ / # ] keys to select "SP LEVEL".
Surround play AX-7 is equipped with listening modes that allow you Selecting the listening mode to enjoy an enhanced sonic ambience with a variety of video sources. SOUND SELECTOR In order to obtain the optimum effect from the MULTI surround modes, make sure to input the proper CONTROL C-AX7 (AX-7 system) speaker settings beforehand.
Surround play 3 P ress the MULTI CONTROL [ % / fi ] keys on the "Stereo (EQ)" Stereo (EQ ON) –– remote contorl to select the listening mode. "PL II Movie"* Pro Logic II Movie "PL II" Then press the [ENTER] key. "PL II Music"* Pro Logic II Music "PL II" • Only "Stereo (EQ)" is displayed when "FRONT SYSTEM" is "PL II Game"* Pro Logic II Game "PL II"...
Troubleshooting Troubles are not always due to malfunction or failure of the system. In case of a trouble, check the following tales before calling for service. Symptom Remedy The power does not become ON or • Insert the system control cord securely all the way. channel switching is not possible.
D: 342 mm (13-7/16") Weight (net) ..............6.8 kg (15.0 lb) Speaker (CRS-W700) • Kenwood follows a policy of continuous advancements Note: The grilles on all the speakers cannot be removed. in development. For this reason specifications may be changed without notice.