Remote Control; General - Insignia NS-32E320A13 User Manual

Insignia 32" 720p LED TV
Problem Solution
No output from one of the
• Adjust the audio balance. See
speakers.
• Make sure that the audio cables are connected
After images appear.
• Do not display a still image, such as a logo,

Remote control

Problem Solution
Remote control does not
• Make sure that the power cord is correctly
work.
connected to your TV and a power outlet.
• Make sure that there are no obstructions
between the remote control and the remote
control sensor on the front of the TV.
• Point the remote control directly at the remote
control sensor on your TV. For the location of the
remote control sensor, see
control" on page 19.
• The supplied batteries are wrapped tightly in
clear plastic. Make sure that you have removed
this plastic from the batteries.
• Make sure that the batteries are installed
correctly. See
batteries" on page 19.
• Replace dead batteries with new batteries. See
"Installing remote control
Trouble programming your
• See instructions and a table of common codes in
existing universal remote
"Programming a different universal remote
control.
control" on page 49.
• Codes are subject to change. For up-to-date
codes, go to
www.insigniaproducts.com/remotecodes
• Replace dead batteries with new batteries. See
"Installing remote control
• Refer to the User Guide that accompanied your
universal remote control and contact the
manufacturer if problems persist.

General

Problem Solution
No power.
• Make sure that the power cord is correctly
connected to your TV and a power outlet.
• Unplug the power cord, wait 60 seconds, then
plug the cord back in and turn on your TV.
• Other devices (for example, a surround sound
receiver, external speakers, fans, or hair dryers)
may be interfering with your TV. Try turning off
one device at a time to determine which device
is causing interference. After you have
determined which device is causing
interference, move it further from the TV to
eliminate the interference.
"No signal" error
• Press INPUT and make sure that you have
message is displayed.
selected the correct input for the device or
service you are trying to use.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
"Adjusting sound
settings" on page 26.
correctly and securely to your TV.
game, or computer image, for an extended
period of time. This can cause a permanent
after-image to be burned into the screen. This
type of damage is not covered by your warranty.
"Aiming the remote
"Installing remote control
batteries" on page 19.
batteries" on page 19.
www.insigniaproducts.com
Problem Solution
After Auto Channel
• Reception can vary by channel depending on the
Search, there are no
broadcast power level of a given station. Contact
channels.
your cable or satellite TV provider.
• Make sure the antenna or cable/satellite TV is
connected securely to your TV.
• Try replacing the cable between the
antenna/cable or cable/satellite box and your
TV.
One or more channels
• Make sure that the channels are not blocked. See
do not display.
"Setting parental control
• Make sure that the channels are not hidden. The
channel may have been deleted from the
channel list. You can tune to the channel by
pressing the number buttons or you can add the
channel back to the channel list. See
channels" on page 28.
• If you are using a cable or satellite box, use the
remote that came with that box to change
channels.
• Make sure that you have the correct input
selected to view channels from the cable or
satellite box.
• If you are using an antenna, the digital channel
signal may be low. To check the digital channel
signal strength, see
strength" on page 30.
Password is lost.
• Enter 9999 to access parental controls, then set
a new password. See
password" on page 30.
Some settings cannot be
• If a setting is grayed, the setting is not available
accessed.
in the current video input mode.
TV cabinet creaks.
• When the TV is in use, the temperature rises
naturally and may cause the cabinet to expand
or contract which can cause a creaking noise.
This is not a malfunction.
Control buttons do not
• Make sure that the Button Lock option is set to
work.
Off. See
• Unplug the power cord, wait a few seconds, then
plug the cord back in and turn on your TV.
TV keeps turning off.
• Make sure that the sleep timer is not turned on.
See "Setting the sleep
: If the problem is not solved by using these troubleshooting
instructions, turn off your TV, then turn it on again.
levels" on page 33.
"Hiding
"Checking the digital signal
"Setting or changing the
"Locking control buttons" on page 31.
timer" on page 37.
47