Advertisement
1.
Manually turn on the device you
Tour of the Remote
want to control.
In most cases, the keys on
this remote perform the same
2.
Press and hold the device key you want to program. The
functions as the keys on your
POWER key illuminates
original remotes once you've
programmed this remote to
While you're holding down the device key, use your other
operate your components.
hand to press and hold the remote's POWER key at the
Many keys on this remote
same time. The POWER key turns off.
have other functions as well.
Illuminated POWER key
serves as an indicator light to
provide feedback.
Device keys (TV,
SAT•CBL•DTC, DVD•VCR) put
the remote in the right mode
3.
Wait until the remote's POWER key
to control your device.
comes on and stays on. Then release
GUIDE and MENU put the
both keys.
remote in menu/guide mode;
they also access the same
4.
Point the remote directly at the front panel of the device you
features as the keys on your
want to control. Press POWER on the remote and wait 2
original remotes.
seconds. The remote is testing a single code for your device.
EXIT exits remote
Did your device turn off?
programming; it also
performs the same functions
YES: Press the STOP key to store
as on your original remotes.
the code. You're done! You've
programmed this device key.
Arrow keys act as navigation
keys in device guides and
NO: Press POWER again. The
remote tests the next code for
menu systems.
your device.
The INPUT•DIGITAL and
Keep pressing POWER every 2
— (dash) key has three
seconds until your device turns off.
functions: (1) it toggles
When it does, press STOP.
through all the video sources
connected to your TV; (2)
TIP: Because there are so many codes, you may have to press
when the remote is in VCR
the POWER key many times—possibly hundreds of times.
mode, this button toggles
between VCR and the TV
NOTES
input; (3) when you're
entering digital channel
Throughout the programming of each key, keep the remote
numbers directly, this button
pointed at the IR sensor of the device you are programming
lets you separate the main
the remote to control.
channel number from the
Test the remote with the device to make sure the device
sub-channel number (such
key is programmed with the correct code for maximum
as 59.1).
functionality. If some features don't work, try a different
code. See the "Testing the Code for Maximum Functionality"
Backlight key (
section below for more information.
backlighting on/off.
During the Manual Code Search, the remote ignores
keypresses that aren't part of the search.
The search times out after two minutes (the POWER key
blinks four times and turns off, and the last programmed
code under that device key is retained).
The POWER key blinks four times and turns off when the
remote has gone through all the codes. The remote exits the
Brand Code Search. If your device hasn't turned off yet, try a
different search method.
IMPORTANT
Testing the Code for Maximum Functionality
1. Try a variety of the device's functions with the remote. If
Because this remote controls more than one device, you
some features of your devices don't work, go to the next
must first "tell" the remote which device you wish to
step to try a different code.
operate. That means, if you wish to operate your TV, you
2. Repeat the Manual Code Search and Entry Method from
must first press the TV key to put the remote in the TV
the beginning. When the device turns off for the first time,
Mode. The remote stays in that device mode until you press
don't press the STOP key, which would store the same
a different device key. For example, if your remote is in TV
code. Instead, with the unit now off, continue to press the
Mode and you want to operate the DVD player, you must
POWER key repeatedly until the unit turns back on.
press the DVD•VCR key to change device modes.
3. Once the unit turns back on, you have found another code
that operates the device. Press the STOP key.
4. Test the key's functionality again by trying a variety of
functions. If the code controls the majority of the device's
functions, programming is complete. If the code stored
does not give maximum functionality, try another code.
Advanced Functions
Reassigning the DVD•VCR Key to Control
a VCR
The DVD•VCR key defaults to control a DVD player. If you want
the DVD•VCR key to control a VCR, you must reassign it.
1.
Press and hold the DVD•VCR key. The POWER key
illuminates. Keep holding down the DVD•VCR key.
2.
While holding down the DVD•VCR key, press and release
the number 2 key on the keypad. The POWER key turns off.
3.
Release the DVD•VCR key. The POWER key blinks four times
and then turns off. The DVD•VCR key is now set to control a
VCR.
4.
Follow the directions in the auto, brand, direct entry, or manual
code search to program the DVD•VCR key for your VCR.
Volume Punch-Through
Volume punch-through allows the VOL and MUTE keys, when
pressed in SAT•CBL•DTC or DVD•VCR modes, to "punch
through" to TV. Volume punch-through occurs automatically
and allows you to control the volume without exiting the
current mode.
Note: Volume punch-through does not occur in cases where
the component code has its own volume/mute controls, such
as some satellite receivers.
Transport Key Punch-Through
Transport key punch-through allows the transport keys (REVERSE,
PLAY, FORWARD, RECORD, STOP, PAUSE, SKIP BACK, SLOW,
and SKIP FWD), when pressed in TV or SAT•CBL•DTC modes,
to "punch through" to DVD•VCR mode. Transport key punch-
through occurs automatically and allows you to use the transport
keys without exiting the current mode. For example, if the
transport keys were last used in DVD mode and accessed again
after pressing the TV key, they will punch through to the DVD.
Note: Transport key punch-through does not occur in cases
where the device code has its own transport key data, such as
a satellite receiver with a built-in DVR.
Channel Lock
Channel lock automatically sends channel commands, like the
CH, GO BACK, and 0–9 number keys, to your satellite receiver,
cable box, or digital TV converter when you're in TV mode.
This can save you keypresses if you use a device other than
your TV to change channels.
To turn channel lock on:
Actual model may vary from
) turns
illustration
1.
Press and hold the device key for the device you use to
change channels. While you're holding down this device
key, use your other hand to press and hold the remote's
CH up key at the same time.
2.
Wait until the remote's POWER key comes on and stays on.
Then release both keys.
3.
Press ENTER to lock channel commands to this device.
To turn channel lock off:
1.
Press and hold the TV key. While you're holding down the
TV key, use your other hand to press and hold the remote's
CH down key at the same time.
2.
Wait until the remote's POWER key comes on and stays on.
Then release both keys.
3.
Press ENTER to start changing channels with your TV.
Code Retrieval
Troubleshooting
Once you've programmed the remote to control your devices,
you may want to record the codes for future reference. If you
used the Direct Code Entry method, this is easy. Just find
Problem: The remote does not operate your device.
the codes you entered and make a note of them in the boxes
•
Make sure the remote is in the correct mode by pressing the
below. If you used one of the Code Search methods to program
corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This
your remote or if you used the Direct Entry method but don't
tells the remote which device to operate.
remember the code, you will need to retrieve each device's
•
Remove any obstacles between the remote and the device. Make
five-digit code. Retrieving the actual code and writing it down
sure you're aiming the remote at the device's IR sensor.
will save you time if you ever need to program the remote
•
Make sure the batteries are fresh and are properly installed.
again. If the codes are recorded, you can use the Direct Entry
Replace the batteries with two new AAA batteries, if necessary
method to reprogram your remote to control your devices,
(see the Battery Installation section).
which is quick and easy.
Problem: The remote can't be programmed to operate your
1.
Press and hold the device key
device.
(TV, SAT•CBL•DTC, DVD•VCR)
whose code you wish to retrieve.
•
If you are testing the remote while programming it, you may be
too far away from the device or at a wrong angle. There must be
The POWER key illuminates.
an unobstructed path between the remote and the IR sensor on
Keep pressing the device key.
the device. Move closer and make sure you point the remote at the
device you're trying to control.
•
If you're using the Direct Entry programming method to enter
2.
While holding the device key down, press and hold the
the codes for your brand and the unit is still not functioning
INFO key. The POWER key turns off. After holding down
properly, try the auto, brand, or manual search method.
both keys for three seconds, the POWER key turns back on.
•
To control combo units, like TV/VCRs or TV/DVDs, you must
3.
Release both keys. The POWER key remains on.
program the individual corresponding device keys to control
each part of the combo unit. Once programmed successfully, the
4.
Starting with the number 1 key, press and release each
TV key controls the TV functions, and the DVD•VCR key controls
number key on the keypad in the following order: 1-9, then
the VCR or DVD functions.
0. The number that causes the POWER key to blink is the
•
Make sure the batteries are fresh and are properly installed.
first number of the code. As you find each number of the
code, write it down for future reference.
Problem: The remote doesn't perform commands properly.
Note: All TV codes begin with the number 1; all VCR and DVR
•
Make sure the remote is in the correct mode by pressing the
codes begin with the number 2; all DVDs, the number 3; and
corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This
all satellite receivers, cable boxes and DTV converters, the
tells the remote which device to operate.
number 5.
•
Make sure device is ready (for example, the DVD player has a
5.
Repeat step 4 until you have retrieved all five numbers in
disc loaded).
the code. After the fifth number is retrieved, the POWER
•
You may have pressed an invalid key for the mode the remote is in.
key blinks briefly, then turns off.
•
If you're trying to enter a channel number directly, try pressing
TIP: To exit the Code Retrieval Mode at any time, press the
the ENTER key after entering the channel number as this is a
requirement of certain models and brands.
EXIT key.
•
There is a possibility that a programmed code may only be
Note: If you press an invalid key during the Code Retrieval
able to control some of your device features (for example, only
process, the remote will not respond. If you do not press a
turns a device on and off). To confirm that the device key is
valid Code Retrieval key (TV, SAT•CBL•DTC, DVD•VCR, INFO,
programmed with the correct code for maximum functionality,
EXIT), Code Retrieval times out after 15 seconds. The POWER
test the device. Attempt to control a variety of the device's
key blinks four times, and then turns off.
functions with the remote. If some of the features of your
devices don't work, try programming the remote with a different
code in the list using the Direct Code Entry Method, until you
find the code that allows the remote to control the majority of
TV CoDe
SAT•CBL•DTC CoDe
your device's functions. Different codes can provide different
levels of functionality.
1
5
Problem: The POWER key does not light when you press a key.
•
You may have pressed an invalid key for the mode the remote is in.
SAT
CABLE
dTv ConvErTEr
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This
tells the remote which device to operate.
DVD•VCR CoDe
•
Make sure the batteries are fresh and are properly installed.
Replace the batteries with two new AAA batteries, if necessary
(see the Battery Installation section).
dvd
vCr
Problem: The remote will not change channels on device.
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This
tells the remote which device to operate.
•
Press the ENTER key after you enter a channel number.
•
Remove any obstacles between the remote and the device. Make
sure to aim the remote at the IR sensor on the device.
Problem: The device's menu does not appear on the TV screen.
•
Make sure you have connected the device to your TV properly and
selected the correct input. (See your devices' Owner's Manuals for
proper connection procedures.)
•
Make sure the remote is in the correct mode by pressing the
corresponding device key (TV, SAT•CBL•DTC, DVD•VCR). This
tells the remote which device to operate.
•
Menu access isn't supported for all brands. You may need to use
your original remote control to access menu functions for some
devices.
For more information, please visit www rcaaccessories.com
Consumer Help Line: 1-800-420-7968
Care and Maintenance
• Keep the remote dry. If it gets wet, wipe it dry immediately.
• Use and store the remote only in normal temperature environments.
• Handle the remote gently and carefully. Don't drop it.
• Keep the remote away from dust and dirt.
• Wipe the remote with a damp cloth occasionally to keep it looking new.
• Modifying or tampering with the remote's internal devices can cause
malfunction and invalidate its warranty.
Limited Lifetime Warranty
Audiovox Electronics Corporation (the "Company") warrants to you the
original retail purchaser of this product that should it, under normal use
and conditions, be proven defective in material or workmanship during
its lifetime while you own it, such defect(s) will be repaired or replaced
(at the Company's option) without charge for parts and repair labor. To
obtain repair or replacement within the terms of this Warranty, the product
is to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to the Company at the
address shown below.
This Warranty does not cover product purchased, serviced or used outside
the United States or Canada. This Warranty is not transferable and does
not extend to costs incurred for installation, removal or reinstallation of
the product. This Warranty does not apply if in the Company's opinion,
the product has been damaged through alteration, improper installation,
mishandling, misuse, neglect, accident, or the simultaneous use of different
battery types (e.g. alkaline, standard or rechargeable).
THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS
LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO
EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE
PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY
IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE SHALL
BE LIMITED TO DURATION OF THIS WARRANTY. IN NO CASE SHALL
THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL
DAMAGES WHATSOEVER. No person or representative is authorized
to assume for the Company any liability other than expressed herein in
connection with the sale of this product.
Some states/provinces do not allow limitations on how long an implied
warranty lasts or the exclusion or limitation of incidental or consequential
damage so the above limitations or exclusions may not apply to you. This
Warranty gives you specific legal rights and you may also have other rights,
which vary from state/province to state/province.
U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge,
New York 11788
CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road,
Unit 3, Door 16, Mississauga, Ontario L5T 3A5
©2010 Audiovox Accessories Corporation
Trademark(s) ® Registered
RCRN03BR US 01
Advertisement
