Page of 2
Download Bookmark Comment

RCA RCRN03BR Owner's Manual

Rca universal remote user manual.
Hide thumbs
   
Brand Code Search
3.
Did your device turn off?
Press and hold the device key you want to program (the
NOTES
Step 2: Program your remote
POWER key illuminates).
The Brand Code Search goes through only the codes for one of
YES: Go to step 5.
Throughout the programming of each key, be sure to keep
the select brands listed in the accompanying code list. If your
While you're holding down the device key, use your other
NO: Press PLAY again. The remote tests the next batch of
the remote pointed at the IR sensor of the device you are
brand of device is listed, this search can be very quick and easy.
To use this universal remote with your home entertainment
hand enter the first five-digit code for your brand in the
10 codes.
currently programming the remote to control.
system, first you need to program it to control your devices.
code list (the POWER key turns off after the first digit).
Test the remote with the device to make sure the device
There are four ways you can program the universal remote to
Keep pressing PLAY every 5 seconds until your device turns
TIPS: Each device key is associated with a type of
key is programmed with the correct code for maximum
operate your devices:
off.
RCRN03BR
device—the TV is preset to search for TVs, SAT•CBL•DTC for
functionality. If some features don't work, try a different
satellite receivers, cable boxes or digital TV converters, and
The Auto Code Search goes automatically through all the
5.
code. See the "Testing the Code for Maximum Functionality"
When your device turns off, press
DVD•VCR for DVD players. To program the DVD•VCR key
codes for the device you're trying to control. It's the easiest
section below for more information.
the REVERSE key on the remote
to control a PVR or VCR, see the Reassigning the DVD•VCR
method, but it can sometimes take longer than some of the
Universal Remote Control
and wait at least 2 seconds.
During the Brand Code Search, the remote ignores
Key to Control a VCR section.
other programming methods.
The remote tries the last of the
keypresses that aren't part of the search.
Owner's Manual
previous ten codes.
The Brand Code Search searches through the codes for
To exit without saving a new code at any point in the Brand
The search times out after two minutes (the POWER key
Code Search, press the EXIT key.
select brands of devices. It's not as easy as the auto code
blinks four times and turns off, and the last programmed
Manual del Propietario (parte posterior)
Did your device turn on?
search, but it can be faster.
code under that device key is retained).
YES: Press the STOP key. You're
done! You've programmed this
1.
The POWER key blinks four times and turns off when the
The Direct Code Entry lets you enter a code from the
Manually turn on the device you
remote has gone through all the codes. The remote exits the
device key.
accompanying code list for your brand of device. It's not as
want to control.
Brand Code Search. If your device hasn't turned off yet, try a
easy as the other methods, but it's potentially the fastest
NO: Press REVERSE again. The remote tests the next
SAVE THIS MANUAL AND THE CODE LISTS!
different search method.
method.
code in the batch.
Remote controls can sometimes lose their programming
4.
The Manual Code Search lets you manually go through
Keep pressing REVERSE every 2 seconds until your device
When you've finished entering
when you change the batteries. Make sure you keep the
all the codes for the device you're trying to control.
turns back on. When it does, press STOP.
the five-digit code, keep holding
manual and code lists in a safe place so that you can
2.
Find your device's brand in the
down the device key and look at
reprogram the remote if you need to.
Note: If you accidentally press the REVERSE key after your
Brand Code list section of the
Testing the Code for Maximum Functionality
the POWER key.
device turns on, press the FORWARD key. Then, wait two
Auto Code Search
Tip: This remote is already programmed to operate most
accompanying code list. Circle
1. Try a variety of the device's functions with the remote. If
seconds to see if your device turns off again.
Is the POWER key
RCA-branded TVs, DVD players, and satellite receivers.
the number for your brand and
The Auto Code Search goes automatically through all the
some device features don't work, go to the next step to try
illuminated?
Just press the corresponding key—DVD•VCR for a DVD
keep the list handy.
codes for the device you're trying to control. When you find
a different code.
NOTES
player, TV for a television, SAT•CBL•DTC for a satellite
YES: You're done! You've programmed this device key.
the one that operates your device, you can stop the search and
2. Repeat the Brand Code Search from the beginning. When
receiver.
store that code.
Throughout the programming of each key, be sure to keep
NO, it blinked four times and turned off: You have
the device turns off for the first time, don't press the STOP
the remote pointed at the IR sensor of the device you are
either entered a code number that is not in the code lists
key, which would store the same code. Instead, with the
3.
currently programming the remote to control.
Press and hold the device key you want to program. The
or missed a step in the code entry procedure. Try step 3
unit now off, continue to press the POWER key repeatedly
TIPS: Each device key is associated with a type of
POWER key illuminates.
Step 1: Install your batteries
again.
Test the remote with the device to make sure the
until the unit turns back on.
device—the TV is preset to search for TVs, SAT•CBL•DTC
device key is programmed with the correct code for
for satellite receivers, cable boxes or digital TV converters,
While you're holding down the device key, use your other
3. Once the unit turns back on, you have found another code
NOTES
and DVD•VCR for DVD players. To program the DVD•VCR
maximum functionality. If some features don't work, try
hand to press and hold the remote's POWER key at the
that operates the device. Press the STOP key.
Your universal remote requires two AAA alkaline batteries (not
key to control a PVR or VCR, see the Reassigning the
a different code. See the "Testing the Code for Maximum
Test the remote with the device to make sure the device
same time. The POWER key turns off.
included).
4. Test the key's functionality again by attempting to control
DVD•VCR Key to Control a VCR section.
Functionality" section below for more information.
key is programmed with the correct code for maximum
a variety of the device's functions. If the code that has
functionality. If some features don't work, try a different code
To install the batteries:
To exit without saving a new code at any point in the Auto
During the Auto Code Search, the remote ignores
been stored controls the majority of the device's functions,
in the list.
keypresses that aren't part of the search.
1.
Code Search, press the EXIT key.
programming is complete. If the code stored does not give
Remove the battery
Remember to enter the code for future reference in the box
maximum functionality, try another code.
compartment cover.
The search times out after two minutes (the POWER key
provided in the Code Retrieval section of this manual.
blinks four times and turns off, and the last programmed
If your brand isn't listed in the code list, use one of the Code
2.
1.
Insert the batteries, matching
Manually turn on the device you
code under that device key is retained).
Search methods to program the remote control. (Refer to the
the batteries to the (+) and
want to control.
Auto and Manual Code Search methods.)
4.
The POWER key blinks four times and turns off when the
(–) marks inside the battery
Wait until the POWER key comes on
remote has gone through all the codes. The remote exits
compartment.
and stays on. Then release both keys.
If you release the device key any time during the Direct Code
Direct Code Entry
the Auto Code Search. If your device hasn't turned off yet,
Entry procedure, the POWER key blinks four times, and the
3.
try a different search method.
Direct Code Entry lets you enter a code from the accompanying
Push the battery cover back into
process is exited. The last programmed code under the
2.
Press and hold the device key you want to program. The
code list for your brand of device. It's not as easy as the other
place.
device key is retained.
POWER key illuminates.
methods, but it's potentially the fastest method.
5.
Look at the numbers you circled for
While you're holding down the device key, use your other
Battery Precautions:
your device's brand code number.
hand to press and hold the remote's POWER key at the
TIP: Each device key is associated with a type of device—
Testing the Code for Maximum Functionality
Press those numbers on the remote
• Do not mix old and new batteries.
same time. The POWER key turns off.
the TV is preset to search for TVs, SAT•CBL•DTC for
1. Try a variety of the device's functions with the remote. If
keypad.
• Do not mix alkaline, standard (carbon-zinc) or
satellite receivers, cable boxes or digital TV converters, and
Manual Code Search
some device features don't work, go to the next step to try
rechargeable (nickel-cadmium) batteries.
Note: For single-digit brand codes,
DVD•VCR for DVD players. To program the DVD•VCR key
a different code.
The Manual Code Search lets you go one-by-one through all the
• Always remove old, weak or worn-out batteries promptly
press the 0 key first (for example, 0-5
to control a PVR or VCR, see the Reassigning the DVD•VCR
codes for the device you're trying to control. When you find the
2. Repeat the Auto Code Search Method from the beginning.
and recycle or dispose of them in accordance with Local
for 5).
Key to Control a VCR section.
When your device turns off, do not stop searching.
one that operates your device, you can stop the search and store
and National Regulations.
6.
Point the remote directly at the
that code.
Instead, with the unit now off, continue to press the PLAY
key every 5 seconds until the unit turns back on.
front panel of the device you want
1.
Manually turn on the device you
TIPS: The Manual Code Search method may take a long time
to control. Press POWER on the
Battery Saver
3. Once the unit turns back on, press the REVERSE key on the
want to control.
because the remote searches through all of the codes in
remote and wait 2 seconds. The
Your universal remote control saves battery power by
remote every 2 seconds until your device turns off again.
3.
its memory one-by-one. If your brand is listed in the Brand
remote is testing a single code for
Wait until the POWER key comes
automatically turning off if any key is pressed for more than
When your device turns off again, press the STOP key.
Codes or the Code Lists, first try the Brand Code Search or
your device's brand.
on and stays on. Then release
60 seconds. This saves your battery life should your remote
the Direct Code Entry method.
4. Test the key's functionality again by attempting to control
both keys.
get stuck in a place where the keys remain depressed, such as
Did your device turn off?
a variety of the device's functions. If the code that has
between sofa cushions.
Each device key is associated with a type of device—the TV is
been stored controls the majority of the device's functions,
2.
Find the Code List that came with
YES: Press the STOP key to store the code. You're done!
preset to search for TVs, SAT•CBL•DTC for satellite receivers,
programming is complete. If the code stored does not give
the remote. Locate the section for
You've programmed this device key.
cable boxes or digital TV converters, and DVD•VCR for DVD
maximum functionality, try another code.
4.
the type of device you're trying to
Point the remote directly at the
players. To program the DVD•VCR key to control a PVR or
NO: Press POWER again. The remote tests the next code
program, and find your brand in
front panel of the device you
VCR, see the Reassigning the DVD•VCR Key to Control a VCR
for your brand.
that section. Circle the codes for
want to control. Press PLAY on
section.
the remote and wait 5 seconds.
your brand and keep them handy.
Keep pressing POWER every 2 seconds until your device
The remote is testing a batch of
To exit without saving a new code at any point in the Manual
turns off. When it does, press STOP.
10 codes on your device.
Code Search, press the EXIT key.

   Related Manuals for RCA RCRN03BR

   Summary of Contents for RCA RCRN03BR

  • Page 1

    Auto Code Search Tip: This remote is already programmed to operate most RCA-branded TVs, DVD players, and satellite receivers. The Auto Code Search goes automatically through all the Just press the corresponding key—DVD•VCR for a DVD codes for the device you’re trying to control.

  • Page 2

    U.S.A.: Audiovox Electronics Corporation, 150 Marcus Blvd., Hauppauge, New York 11788 CANADA: Audiovox Return Center, c/o Genco, 6685 Kennedy Road, Unit 3, Door 16, Mississauga, Ontario L5T 3A5 ©2010 Audiovox Accessories Corporation Trademark(s) ® Registered RCRN03BR US 01...

Comments to this Manuals

Symbols: 0
Latest comments: