9 • Operating and Cleaning Your Ceiling use a solid-state speed control with this fan. Use only Hunter speed Fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 controls, which are solid state.
If you want to use an existing fan site, complete the following checklist to System determine if the site is acceptable and safe for your new Hunter fan. If you cannot check off every item, prepare a new fan site as described on this page.
Page 4
ANSI/NFPA 70. If your ceiling fan, go to your fan manual and continue with Section 2 • Installing the you are unfamiliar with wiring, use a Ceiling Plate. qualified electrician. 45003-01 • 07/12/2011 • Hunter Fan Company...
Page 5
Support Brace Hunter’s patented mounting system provides you maximum installation flexibility and ease. You can install your Hunter fan in one of two ways, depending on ceiling height and your preference: Standard or Angled mounting. The steps in this manual include instructions for Ceiling both Installer’s Choice mounting methods.
• Drill holes for and install wood screws. • Identify and connect electrical wires. • Lift 40 pounds. If you need help installing the fan, your Hunter fan dealer can direct you to a licensed installer or electrician. Gathering the Tools You will need the following tools for installing the fan: •...
Tighten the screws into the 9/64” pilot holes; do not use lubricants on the screws. Do not over tighten. Flat Washer Steps 2-2 – 2-4 Ceiling Peak Ceiling Peak Large Large Opening Opening 3” Screw LEFT RIGHT Step 2-3 (Angled Ceiling Only) 45003-01 • 07/12/2011 • Hunter Fan Company...
(Rotate the fan until you hear the notch pop into place.) Go to 4 • Wiring the Fan . Indent WARNING: Fan may fall if not assembled as directed in these installation instructions. Steps 3-4 – 3-5 45003-01 • 07/12/2011 • Hunter Fan Company...
4-7. Spread the wires apart, with the grounded wires on one side of the outlet box and the ungrounded wires on the other side of the outlet box. 45003-01 • 07/12/2011 • Hunter Fan Company...
5-6. Twist canopy trim ring clockwise to secure the canopy. Should you need to remove the canopy trim ring, follow these steps: 1. Twist canopy trim ring counter clockwise until it releases from canopy. Step 5-3 Step 5-4 Canopy Step 5-5 Screw 45003-01 • 07/12/2011 • Hunter Fan Company...
6 • Assembling the Blades Step 6-1 (Detail) Hunter fans use several styles of fan blade irons (brackets that hold the blade to the fan). 6-1. Your fan may include blade grommets. If your fan has grommets, insert them by hand into the holes on the blades.
7 • Completing Your Installation With a Bowl Light Fixture Your Hunter fan comes with an integrated light fixture assembly. WARNING: Use only the light fixture supplied with this fan model. 7-1. To attach the upper switch housing, partially install two housing assembly screws into the switch housing mounting plate.
Plug Exceeding the wattage limit marked on the MAX wattage Connector Detail sticker affixed to the light socket(s) may result in fire hazard or improper operation. Housing Assembly Screw 45003-01 • 07/12/2011 • Hunter Fan Company...
Page 14
7-9. Place the finial over the threaded portion of the heater vent and twist it as shown to tighten it against the glass bowl. Switch Housing Screws (3) Light Bulbs (B10 Candelabra Base 40 Watt Maximum) Threaded Portion of Heater Vent Glass Bowl Finial 45003-01 • 07/12/2011 • Hunter Fan Company...
Page 15
CAUTION: The remote control device complies with part 15 of the Tabs FCC rules. Changes or modifications not expressly approved by Hunter Fan Company could void your authority to operate this equipment. Operation is subject to the following two conditions: 1.
Note: The receiver (built into the fan) has a memory function that retains the last DIP switch code setting. The setting will not change in the event of power failure or if the power to the fan is inadvertently shut off. 45003-01 • 07/12/2011 • Hunter Fan Company...
If you need parts or service assistance, please call 888-830-1326 (In Canada, call 866-268-1936) or visit us at our website at http://www.hunterfan.com. Hunter Fan Company 7130 Goodlett Farms Parkway #400 Memphis, Tennessee 38016 45003-01 • 07/12/2011 • Hunter Fan Company...