Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for EAW CXA160 / CXA80
Summary of Contents for EAW CXA160 / CXA80
- Page 1 INSTRUCTION MANUAL 160 / Integrated Amplifiers...
-
Page 2: Table Of Contents
16. Servicing — The user should not attempt to service the Component beyond those means described in this operating manual. All other servicing should be referred to the EAW Commercial Service Department. Part No. 0022185 Rev. B 03/07 © 2007 LOUD Technologies Inc. All Rights Reserved. -
Page 3: Introduction
• Universal power supply, 100 VAC–240 VAC, 50–60 Hz • Automatic switching to 24 VDC backup power input • 2 RU rack-mountable APPLICATIONS • Foreground/background music systems • Paging systems • Continuous-duty applications • Sound reinforcement systems CXA160 / CXA80 –... -
Page 4: Front Panel Features
In the detented center position, there is no change in level. The maximum boost and cut is 12 dB. 3. VOLUME Use this volume control to adjust the sound output level to your speakers. – CXA160 / CXA80 4. STATUS LEDS These LEDs show: OVERLOAD (RED) SIGNAL PRESENT (AMBER) -
Page 5: Rear Panel Features
It is useful when using smaller speakers that do not reproduce the low frequencies well. 3. 10 dB pad enable. Select UP to reduce the input level by 10 dB. Enabled Enabled CXA160 / CXA80 –... - Page 6 With normal priority source material playing, adjust the pot until the LED lights only occasionally during the loudest moments of your program. – CXA160 / CXA80 15. Priority DIP switch This five-pole DIP-switch allows you to configure all four priority input types, as shown in this table and described below.
- Page 7 This external connector can be used to connect to an external device to initiate a “fault” action as dictated by the user. Additionally, the “fault” LED on the front of the amplifier is lit. 3 CXA160 / CXA80 –...
- Page 8 (clockwise), and tighten down the screw with a screwdriver. – CXA160 / CXA80 HIGH IMPEDANCE If you are using a constant-voltage distributed speaker system, connect either the 25 V, 70 V, or 100 V output terminal to the "+"...
- Page 9 Note: The unit will not charge the battery, so you should have a dedicated charging system. Note also, that when running on DC power, the output is lower than when running on AC power. 100V 100V CXA160 / CXA80 –...
-
Page 10: Thermal Considerations
Pin 1 = Shield Pin 2 = Hot (+) Pin 3 = Cold (–) – CXA160 / CXA80 1/4" TRS Phone Plugs and Jacks “TRS” stands for Tip-Ring-Sleeve, the three connections available on a stereo 1/4" or balanced phone jack or plug. -
Page 11: Typical Hookup Diagram
7. TYPICAL HOOKUP DIAGRAM CXA160 / CXA80 –... -
Page 12: Specifications
Design refinements are introduced into existing products without notice as a routine expression of that philosophy. For this reason, any current EAW Commercial product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated. -
Page 13: Block Diagram
CXA160 / CXA80 –... -
Page 14: Service Information
Return Authorization Number in order to obtain warranty service at the factory or at an authorized service center. You can also email EAW Commercial Tech Support at: support@eawcommercial.com 2. Pack the unit in its original packaging. THIS IS VERY IMPORTANT. -
Page 15: Eaw Commercial Warranty
Exterior defects in or damage to the exterior appearance are specifically excluded from this warranty. EAW Commercial distributors shall not be liable for incidental or consequential damages resulting from the use of EAW Commercial products. Repairs and/or modifications by other than an Authorized EAW Commercial Distributor automatically voids this warranty. - Page 16 EAW Commercial A LOUD Technologies Inc. Company EAW Commercial | One Main Street | Whitinsville, MA 01588 USA | TEL toll free within US/Canada 888.337.7404 TEL outside US 425.892.6503 | FAX 425.485.1152 | www.eawcommercial.com © 2007 LOUD Technologies Inc. All Rights Reserved.