Fujitsu MAV2036RC - 36.7 GB Hard Drive Installation Requirements
Manual/user guide
Hide thumbs
Also See for MAV2036RC - 36.7 GB Hard Drive:
- Product/maintenance manual (92 pages) ,
- Technical manual (392 pages)
Advertisement
Quick Links
CHAPTER 4
Installation Requirements
This chapter describes the environmental, mounting, power supply, and connection requirements.
4.1
Mounting Requirements
4.1.1
Dimensions
Figures 4.1 show the dimensions of the HDD and the location of the mounting screw holes.
C141-E219
4.1
Mounting Requirements
4.2
Power Supply Requirements
4.3
Connection Requirements
Figure 4.1
[Units: mm]
Dimensions
4-1
Advertisement
Related Manuals for Fujitsu MAV2036RC - 36.7 GB Hard Drive
Summary of Contents for Fujitsu MAV2036RC - 36.7 GB Hard Drive
-
Page 1: Chapter 4 Installation Requirements
CHAPTER 4 Installation Requirements Mounting Requirements Power Supply Requirements Connection Requirements This chapter describes the environmental, mounting, power supply, and connection requirements. Mounting Requirements 4.1.1 Dimensions Figures 4.1 show the dimensions of the HDD and the location of the mounting screw holes. [Units: mm] Figure 4.1 Dimensions... -
Page 2: Mounting Orientations
Installation Requirements 4.1.2 Mounting orientations The permissible orientations of the HDD are shown in Figure 4.2, and the tolerance of the angle is ±5° from the horizontal plane. As show in Figure 4.2, the drive can be installed flat on any of its six sides. Inclination from a vertical or horizontal plane should not exceed 5°. -
Page 3: Mounting Requirements
4.1 Mounting Requirements 4.1.3 Notes on mounting Damage Never remove any labels from the drive or deface them in any way. The mounting screws must use M3 × 0.5 metric Examples of mounting frame structure Special attention must be given to mount the HDD as follows. As shown in Figure 4.3, use the frame with an embossed structure, or the like. - Page 4 Installation Requirements Figure 4.3 Mounting frame structure Never cover the vent hole as shown in Figure 4.4. Vent hole Label Figure 4.4 Breathing hole location C141-E219...
- Page 5 4.3 Connection Requirements Environmental temperature Temperature condition at installed in a cabinet is indicated with ambient temperature measured 30 mm from the disk drive. At designing the system cabinet, consider following points. • Make a suitable air flow so that the DE surface temperature never exceed 60°C. •...
- Page 6 Installation Requirements Service clearance area The service clearance area, or the sides which must allow access to the HDD for installation or maintenance, is shown in Figure 4.6. [Surface X] • Holes for mounting screw [Surface Y] (Both Side) • Interface connection [Surface Z] •...
- Page 7 4.2 Power Supply Requirements Power Supply Requirements Allowable input voltage and current The power supply input voltage measured at the power supply connector pin of the HDD (receiving end) must satisfy the requirement given in Subsection 2.1.3. (For other requirements, see Items (4) below.) Current waveform (reference) Figure 4.7 shows the waveform of +12V DC.
- Page 8 Installation Requirements Noise filter To eliminate AC line noise, a noise filter should be installed at the AC input terminal on the HDD power supply unit. The specification of this noise filter is as follows: • Attenuation: 40 dB or more at 10 MHz •...
- Page 9 4.3 Connection Requirements 4.3.2 Interface connector Figure 4.10 shows the SAS type interface connector (SAS plug) overview. Table 4.2 lists the signal allocation of the SAS plug on the HDD. Figure 4.10 SAS plug connector overview C141-E219...
-
Page 10: Ready Led
Installation Requirements Table 4.2 Interface connector (SAS plug) signal allocation:CN1 Pin No. Signal Description GND for SAS Primary Port SAS Primary Port Receive(positive) signal SAS Primary Port Receive(negative) signal GND for SAS Primary Port SAS Primary Port Transmit(negative) signal SAS Primary Port Transmit(positive) signal GND for SAS Primary Port Note1 GND for SAS Secondary Port...