Remote Control; General; Maintenance; Cleaning - Dynex DX-24E150A11 User Manual

26
DX-24E150A11

Remote control

Problem Solution
Remote control • Make sure that the power cord is plugged
does not work. in.
• Make sure that there are no obstructions
between the remote control and the
remote control sensor on the front of the
TV.
• Make sure that the batteries are installed
correctly. For more information, see
"Installing remote control batteries" on
page 6.
• Replace the batteries. For more
information, see "Installing remote control
batteries" on page 6.
Trouble • See instructions and a table of common
programming your codes in "Programming a universal remote
existing universal control to work with your TV" on page 7.
remote control. • Codes are subject to change. For up to date
codes, go to www.dynexproducts.com.
• Replace the batteries. For more
information, see "Installing remote control
batteries" on page 6.
• Refer to the User Guide that accompanied
your universal remote control and contact
the manufacturer if problems persist

General

Problem Solution
One or more • Make sure that the channels are not blocked.
channels do not For more information, see "Setting parental
display. control levels" on page 19.
• Make sure that the channels are not hidden.
For more information, see "Hiding channels"
on page 15.
• The channel may have been deleted from the
channel list. You can tune to the channel by
pressing the number buttons or you can add
the channel back to the channel list. For more
information, see "Changing channel settings"
on page 14.
Password is lost. • Enter 9999 to access parental controls, then
set a new password. For more information, see
"Setting parental control levels" on page 19.
Some settings • If a setting is grayed, the setting is not
cannot be available in the current video input mode.
accessed.
TV cabinet creaks. • When the TV is in use, the temperature rises
naturally and may cause the cabinet to
expand or contract which can cause a
creaking noise. This is not a malfunction.
Control buttons • Disconnect the power cord, wait a few
on the TV do not seconds, then reconnect the power cord and
work. turn on the TV.
Note: If the problem is not solved by using these troubleshooting
instructions, turn off your TV, then turn it on again.

Maintenance

Cleaning

• Clean your TV with a soft, dry cloth. If surfaces are extremely
dirty, use a soft cloth dampened with a weak detergent solution.
• Use an eyeglass cleaner to clean the screen. Never use alcohol,
paint thinner, or benzine.
• Before using a chemically treated cloth, read the instructions that
came with the cloth.

Specifications

Design and specifications are subject to change without notice.
Dimensions and weight are approximate.
LCD
TV type
24-inch TFT LCD
TV panel
NTSC-M, ATSC
TV system
VHF: 2 - 13
Channels
UHF: 14 - 69
CATV: 1 - 125
CADTV: 1-135
DTV: 2 - 69
BTSC system
Audio multiplex
3W × 2
Audio output
AC 120 V, 60 Hz
Power requirement
55 W
Power consumption
16.22 x 22.83 x 5.51 inches (412 x 580 x 140 mm)
Dimensions
1.02 lbs (5 kg)
Weight
Composite (AV) video/left and right audio (1)
Input terminals
Component video/left and right audio (1)
HDMI (1)
VGA/audio (1)
Antenna (1)
Headphone jack (1)
Output terminals
Service Port (1)
Control terminals

Legal notices

FCC Part 15
This device complies with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired
operation.
This equipment has been tested and found to comply within the limits
for a class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
Maintenance