Table of Contents
Advertisement
Quick Links
Read this instructions carefully before use
Minoura Japan Headquarters
(for all customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp
www.minoura.jp
Indoor Bicycle Trainer instructions manual
Tire Size Capacity Range <with Z-Adaptor>
<w/o Z-Adaptor>
Minoura North American Tech Center
1996 East Avenue, Hayward, CA 94541 U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
Made in Japan
M70-R
M80-R
26x1.00 - 29x2.10
20x1-3/8 - 700x32c
(for U.S. residents only)
(ver.1.2 2010/2)
Advertisement
Table of Contents
Related Manuals for MINOURA M70-R
Summary of Contents for MINOURA M70-R
- Page 1 M70-R M80-R (ver.1.2 2010/2) Indoor Bicycle Trainer instructions manual Tire Size Capacity Range <with Z-Adaptor> 26x1.00 - 29x2.10 <w/o Z-Adaptor> 20x1-3/8 - 700x32c Read this instructions carefully before use Minoura Japan Headquarters Minoura North American Tech Center (for all customers) (for U.S. residents only) 1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A. Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899 Email: minoura@minoura.jp Email: support@minourausa.com www.minoura.jp Made in Japan...
-
Page 2: Important Notice
• If you feel any strange noise or smell, stop using M70-R/M80-R immediately and contact the retailer where you purchased the M70-R/M80-R. • Any warranty will be void if you use M70-R/M80-R for other purpose than instructed. Minorua offers 1-year limited warranty on the resistance unit and 5-year limited warranty on the frame from the date of your purchase for any problem caused by manufacturer's defect. - Page 3 M70-R / M80-R Schematics UF-9 UF-6 UF-7 UF-8 BF-3 GM-19 BF-4 BF-6 M5-2 BF-4 EM-1 BF-6 MF-3 EM-4 EM-3 EM-6 EM-2 EM-11 LM-10 EM-5 EM-9 EM-10 EM-14 EM-17 EM-8 EM-15 BF-3: M70/80 Main Frame (White) EM-1: Outer Cap BF-4: Leg Rubber Cover (Red) EM-2: Axle Holder BF-6: Leg Rubber EM-3: Drive Roller & Bearing...
- Page 4 Replace your rear wheel quick release skewer to the supplied one. Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub...
- Page 5 Too tight setting will cause damage to both (Fig. H) (Fig. I) M70-R/M80-R and your bike frame. Too loose setting may cause the bike to come out of the trainer during use. - Page 5 -...
- Page 6 Please note too much and too less roller pressure will bring premature tire wear. Keep correct roller pressure and maintain the air pressure in correct level before using M70-R/M80-R. TIPS If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.
- Page 7 It just works to adjust the coupling distance. To remove the bike from M70-R/M80-R, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller.
- Page 8 Why My Remote Shifter Doesn't Work Properly? You may have a shifting problem that you cannot set at L or H position properly due to the lengthened inner cable. To fix this problem, follow the steps to adjust the initial cable tension.