Advertisement
Quick Links
Read this instructions carefully before use
Minoura Japan Headquarters
(for all customers)
1197-1 Godo, Anpachi, Gifu 503-2305 Japan
Phone: +81-584-27-3131 / Fax: +81-584-27-7505
Email: minoura@minoura.jp
www.minoura.jp
Indoor Bicycle Trainer – instructions manual
Tire Size Capacity Range <with Z-Adaptor>
<w/o Z-Adaptor>
Minoura North American Tech Center
1996 East Avenue, Hayward, CA 94541 U.S.A.
Phone: 1-510-538-8599 / Fax: 1-510-538-5899
Email: support@minourausa.com
Made in Japan
M60-D
26x1.00 - 29x2.10
20x1-3/8 - 700x32c
(for U.S. residents only)
(ver.1.1 2010/2)
Advertisement
Related Manuals for MINOURA M60-D
Summary of Contents for MINOURA M60-D
- Page 1 M60-D Indoor Bicycle Trainer – instructions manual Tire Size Capacity Range <with Z-Adaptor> 26x1.00 - 29x2.10 <w/o Z-Adaptor> 20x1-3/8 - 700x32c Read this instructions carefully before use Minoura Japan Headquarters Minoura North American Tech Center (for all customers) (for U.S. residents only) 1197-1 Godo, Anpachi, Gifu 503-2305 Japan 1996 East Avenue, Hayward, CA 94541 U.S.A. Phone: +81-584-27-3131 / Fax: +81-584-27-7505 Phone: 1-510-538-8599 / Fax: 1-510-538-5899 Email: minoura@minoura.jp Email: support@minourausa.com www.minoura.jp Made in Japan (ver.1.1 2010/2)
-
Page 2: Important Notice
• It is not possible to convert the non-remote resistance unit to the remote control version one due to a difference in the inside mechanism. • If you feel any strange noise or smell, stop using M60-D immediately and contact the retailer where you purchased the M60-D. - Page 3 BF-5: Leg Rubber Cover (White) EM-2: Axle Holder BF-6: Leg Rubber EM-3: Drive Roller & Bearing UF-7: Clamp Lever Guide EM-4: Main Housing UF-8: Left Side Coupling (for Q/R skewer) EM-5: Alloy Rotor UF-17: Right Side Coupling & Clamp Lever EM-11: Connecting Plate UF-18: Coupling Lock Ring (White) EM-13: R esistance Adjust Lever M5-2: Rubber Foot Cap (29mm) EM-16: M agnet Plate (for M60-D) MF-3: Roller Pressure Adjust Knob EM-17: F lywheel Disc (0.6 kgs) LM-10: Base Plate EM-18: F lywheel Cover (White for M60) - Page 3 -...
- Page 4 Replace your rear wheel quick release skewer to the supplied one. Minoura guarantees the stability only when using the supplied skewer due to the coupling inner shape. If your bike is not equipped with quick release skewer and it's a hub nut type, replace the left side coupling (UF-8) to the optional "Left Side Coupling for Hub...
- Page 5 Too tight setting will cause damage to both (Fig. H) (Fig. I) M60-D and your bike frame. Too loose setting may cause the bike to come out of the trainer during use. - Page 5 -...
- Page 6 Please note too much and too less roller pressure will bring premature tire wear. Keep correct roller pressure and maintain the air pressure in correct level before using M60-D. TIPS If it's hard to tighten the knob bolt, lift up the Mag unit by hand then tighten the knob.
- Page 7 It just works to adjust the coupling distance. To remove the bike from M60-D, loosen the knob then lift up om the clamp. If you remove the bike without changing the roller position, the next installation may become difficult because the rear wheel has been pushed forward by the roller.