Zenith P50W38 Service Manual page 73

External Control Device Setup
08. Brightness (Command2:h)
G To adjust screen brightness.
You can also adjust brightness in the Video menu.
Transmission
[k][h][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to 'Real data mapping 1'. See page 27.
Acknowledgement
[h][ ][Set ID][ ][OK][Data][x]
09. Color (Command2:i)
G To adjust the screen color.
You can also adjust color in the Video menu.
Transmission
[k][i][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•
Refer to 'Real data mapping 1'. See page 27.
Acknowledgement
[i][ ][Set ID][ ][OK][Data][x]
10. Tint (Command2:j)
G To adjust the screen tint.
You can also adjust tint in the Video menu.
Transmission
[k][j][ ][Set ID][ ][Data][Cr]
Data Red : 0 ~ Green : 64
•
Refer to 'Real data mapping 1'. See page 27.
Acknowledgement
[j][ ][Set ID][ ][OK][Data][x]
11. Sharpness (Command2:k)
G To adjust the screen sharpness.
You can also adjust sharpness in the Video menu.
Transmission
[k][k][ ][Set ID][ ][Data][Cr]
Data Min: 0 ~ Max: 64
•
Refer to 'Real data mapping 1'. See page 27.
Acknowledgement
[k][ ][Set ID][ ][OK][Data][x]
12. OSD Select (Command2:l)
G To select OSD (On Screen Display) on/off.
Transmission
[k][l][ ][Set ID][ ][Data][Cr]
Data 0: OSD off
Acknowledgement
[l][ ][Set ID][ ][OK][Data][x]
28 Plasma Display Panel
1: OSD on
13. Remote Control Lock Mode (Command2:m)
G To lock the remote control and front panel controls on the
monitor
Transmission
[k][m][ ][Set ID][ ][Data][Cr]
Data 0: Lock off
Acknowledgement
[m][ ][Set ID][ ][OK][Data][x]
•
If you're not using the remote control and front panel con-
trols on the monitor, use this mode. When main power is
on/off, remote control lock is released.
14. PIP / Twin (Command2:n)
G To control the PIP (Picture-in-Picture) or Twin Picture.
You can also control the PIP/Twin picture mode using the PIP
or TWIN PICTURE button on the remote control or in the
Twin menu.
Transmission
[k][n][ ][Set ID][ ][Data][Cr]
Data 0: PIP/DW off
1: PIP
Acknowledgement
[n][ ][Set ID][ ][OK][Data][x]
15. PIP Aspect Ratio (Command2:o)
G To select the PIP picture format.
You can also select the PIP picture format using PIP ARC
on the remote control.
Transmission
[k][o][ ][Set ID][ ][Data][Cr]
Data 0: 4:3
Acknowledgement
[o][ ][Set ID][ ][OK][Data][x]
16. Split Zoom (Command2:p)
G To operate split zoom function and select the split
zoom section number.
Transmission
[k][p][ ][Set ID][ ][Data][Cr]
Data Min: 21 ~ Max: 99
•
Refer to 'Real data mapping 2'.
Acknowledgement
[p][ ][Set ID][ ][OK][Data][x]
* Real data mapping 2
21: Selection 1 of 2 split zoom
24: Selection 4 of 2 split zoom
41: Selection 1 of 4 split zoom
42: Selection 2 of 4 split zoom
44: Selection 4 of 4 split zoom
45: Selection 5 of 4 split zoom
91: Selection 1 of 9 split zoom
99: Selection 9 of 9 split zoom
1: Lock on
2: DW1
3: DW2
1: 16:9