Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 A Message From DaimlerChrysler Corporation . . . 5 How To Use This Manual ....5 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: A Message From Daimlerchrysler Corporation
A MESSAGE FROM DAIMLERCHRYSLER CORPORATION DaimlerChrysler Corporation and Cummins welcome you as a new Dodge Ram Cummins Turbo Diesel- powered truck owner. Almost 100% of the heavy duty trucks in the United States are diesel powered because of the fuel economy, rugged durability, and high torque which permits pulling heavy loads.
Page 6: Van Conversions/Campers
6 INTRODUCTION WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 7: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 8: Vehicle Modifications / Alterations
8 INTRODUCTION VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Key-In-Ignition Reminder ....11 Sentry Key —...
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Set The Alarm ..... .29 To Disarm The System ....30 Windows .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith.
Page 12: 12 Things To Know Before Starting Your Vehicle
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Security Light , located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Light will flash continuously to signal that the vehicle has been immobilized.
Page 13 Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds.
Page 14: Ignition And Steering Lock
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK Insert the key fully, and then turn the switch to one of the five illustrated positions. The key can be inserted or withdrawn only in the LOCK position. Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide...
Page 15: Automatic Transmissions
Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve- hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily.
Page 16: Door Key
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock...
Page 17: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
Page 18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking —...
Page 19 Automatic Door Locks If this feature is enabled, your door locks will lock automatically when the vehicle’s speed exceeds 15 mph. This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: 1.
Page 20 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE This feature will not operate if any of the conditions above are not met or following has occurred: • Any manual operation of a door lock switch has occurred. Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure:...
Page 21: Child Protection Door Lock
Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
Page 22: Remote Keyless Entry - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
Page 23: To Unlock The Doors
To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds.
Page 24: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Page 25: Using The Panic Alarm
2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ).
Page 26: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE door locks and remote keyless entry systems will func- tion normally. Panic mode will not disarm the security system on vehicles so equipped. Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle.
Page 27: General Information
9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed.
Page 28: Transmitter Battery Service
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.
Page 29: Security Alarm System - If Equipped
SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly.
Page 30: To Disarm The System
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 31: Windows
WINDOWS Power Windows—If Equipped THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models.
Page 32: Sliding Rear Window-If Equipped
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 33: Wind Buffeting
WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized.
Page 34: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
Page 35 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap. 3. When the belt is long enough to fit, insert the latch plate into the buckle until you hear a “click.”...
Page 37 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 39 Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position...
Page 41: Adjustable Upper Shoulder Belt Anchorage
WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 42: Automatic Locking Mode (If Equipped)
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Automatic Locking Mode (if Equipped) In this mode, the shoulder belt is automatically pre- locked. The belt will still retract to remove any slack in the shoulder belt. The automatic locking mode is only available on the front passenger side belt.
Page 43: Seat Belt Pretensioners
WARNING! • A lap belt worn too loose or too high is dangerous. • A belt worn too loose can allow you to slip down and under the belt in a collision. • A belt that is too loose or too high will apply crash forces to the abdomen, not to the stronger hip bones.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Warning System (BeltAlert) will be reactivated if the driver’s seat belt is unbuckled for more than 10 seconds and the vehicle speed is greater than 5 mph (8 km/h). The Enhanced Warning System (BeltAlert) can be en- abled or disabled by your authorized dealer or by following these steps: NOTE: The following steps must occur within the first...
Page 45: Seat Belts And Pregnant Women
Seat Belts and Pregnant Women We recommend that pregnant women use seat belts throughout their pregnancies. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug against the hips as possible. Keep the belt low so that it does not come across the abdomen.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE These airbags are certified to the new Federal regulations that allow less forceful deployments. This vehicle may also be equipped with window bags to protect the driver and passengers in the first and second row sitting next to a window.
Page 47 Airbags inflate in moderate to high speed impacts. Along with the seatbelts, front airbags work with the instrument panel knee bolsters to provide improved protection for the driver and front passenger. Window bags also work with seat belts to improve occupant protection. The seat belts are designed to protect you in many types of collisions.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • The driver and front passenger seats should be moved back as far as practical to allow the airbag room to inflate. WARNING! • Relying on the airbags alone could lead to more severe injuries in a collision.
Page 49 The Window Airbag System, on vehicles equipped, consists of the following: • AIRBAG Readiness Light (shared with the front airbag system) • Window Bags Above the Side Windows. • Airbag Control Module (shared with the front airbag system) • Side impact sensors •...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • If it detects a malfunction in any part of the system, it turns on the light either momen- tarily or continuously. The instrument cluster will flash the seat belt indicator if it detects a fault with the airbag indicator.
Page 51 Passenger Airbag On/Off Switch – (Standard Cab Vehicles Only) The passenger front airbag is to be turned off only if the passenger: • is an infant (less than 1 year old) who must ride in the front seat because there is no rear seat, because the rear seat is too small for a rear-facing infant restraint or THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 because the infant has a medical condition which...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Whenever an airbag is turned off, even a lap/ shoulder belted passenger may hit their head, neck, or chest on the dashboard (instrument panel) or windshield in a crash. This may result in serious injury or death.
Page 53 If you do have a collision which deploys the airbags, any or all of the following may occur: • The nylon airbag material may sometimes cause abra- sions and/or skin reddening to the driver and front passenger as the airbags deploy and unfold. The abrasions are similar to friction rope burns or those you might get sliding along a carpet or gymnasium floor.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate. The window airbag control module will not detect roll over, front or rear collisions.
Page 55 Maintaining Your Airbag Systems WARNING! • Modifications to any part of the airbag system could cause it to fail when you need it. You could be injured because the airbags are not there to protect you. Do not modify the components or wiring, including adding any kind of badges or stickers to the steering wheel hub trim cover or the upper right side of the instrument panel.
Page 56: Child Restraint
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE NOTE: If the speedometer, tachometer or any engine related gauges are not working, the airbag control mod- ule may also be disabled. The airbags may not be ready to inflate for your protection. Promptly check fuse num- bers 52 and 53 in the fuse and relay center.
Page 57 of child restraints can be used rearward-facing: infant carriers and convertible child seats. Both types of child restraints are held in the vehicle by the lap/ shoulder belt. • The infant carrier is only used rearward-facing in the vehicle. It is recommended for children who weigh up to about 20 lbs (9 kg).
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Improper installation can lead to failure of an infant or child restraint. It could come loose in a collision. The child could be badly injured or killed. Follow the manufacturer’s directions ex- actly when installing an infant or child restraint.
Page 59 which are designed to keep the lap portion tight around the child restraint so that it is not necessary to use a locking clip. If the seat belt has a cinching latch plate, pulling up on the shoulder portion of the lap/shoulder belt will tighten the belt.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When your child restraint is not in use, secure it in the vehicle with the seat belt or remove it from the vehicle. Do not leave it loose in the vehicle. In a sudden stop or collision, it could strike the occupants or seat backs and cause serious personal injury.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Standard Cab Passenger Seat Quad Cab Outboard Seat...
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time.
Page 63 rearward-facing infant restraints will also be equipped with a tether strap, a hook and means for adjusting the tension in the strap. In general, you will first loosen the adjusters on the lower straps and tether straps so that you can more easily attach the hook or connector to the lower anchorages and tether anchorages.
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 65 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up”...
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints...
Page 67: New Engine Break-In
Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. •...
Page 68: Safety Tips
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Check the coolant and oil levels frequently. • Vary throttle position at highway speeds when carry- ing or towing significant weight. Because of the construction of the Cummins Diesel engine, engine run-in is enhanced by loaded operating conditions which allow the engine parts to achieve final finish and fit during the first 6,000 miles (10 000 km).
Page 69: Lock Your Vehicle
Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar- ticles of value exposed.
Page 70: Safety Checks You Should Make Inside The Vehicle
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed.
Page 71 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 Door Latches Check for positive closing, latching and locking. Fluid Leaks Check area under vehicle after overnight parking for fuel, water, oil, or other fluid leaks. Also, if fuel fumes are detected the cause should be located and corrected.
Page 73 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......78 Inside Mirror ......78 Automatic Dimming Mirror—...
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Seats ....... . 106 40-20-40 Front Seat .
Page 75 Driver Adjustable Pedals — If Equipped ..123 Adjustment ......123 Electronic Speed Control —...
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Garage Door Opener — If Equipped ..134 Programming Homelink ....136 Canadian Programming/Gate Programming .
Page 77 Storage And Seats — If Equipped ..148 Fold Flat Load Floor — If Equipped ..148 Fold Flat Load Floor — If Equipped ..148 Pickup Box .
Page 78: 78 Understanding The Features Of Your Vehicle
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 79: Automatic Dimming Mirror- If Equipped
Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 80: Exterior Mirrors Folding Feature
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Page 81: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Fold the 7 x 10 inch trailer towing mirrors rearward prior to entering an automated car wash. CAUTION! Do not attempt to fold the 7 x 10 inch trailer towing mirrors forward. The 7 x 10 inch trailer towing mirrors are not designed to be folded forward and doing so will damage the mirrors and/or vehicle.
Page 83: Hands-Free Communication (Uconnect™) - If Equipped
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 HANDS–FREE COMMUNICATION (UConnect™) — IF EQUIPPED UConnect™ is a voice-activated, hands-free, in vehicle communications system. UConnect™ allows you to dial a phone number with your cellular phone* using simple voice commands (e.g., Call Mike Work or Dial 248-555-1212 ).
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversation. The UConnect™ phonebook enables you to store up to 32 names and four numbers per name.
Page 85: Operation
The UConnect™ system can be used with any Hands- Free Profile certified Bluetooth™ cellular phone. If your cellular phone supports a different profile (eg., Headset Profile), you may not be able to use any UConnect™ features. Refer to your cellular service provider or the phone manufacturer for details.
Page 86 To complete the pairing process, you will need to reference your cellular phone owner’s manual. One of the following vehicle specific websites may also provide detailed instructions for pairing with the brand of phone that you have: NOTE: • www.chrysler.com/uconnect • www.dodge.com/uconnect • www.jeep.com/uconnect...
Page 87 The following are general phone to UConnect™ System pairing instructions: • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Setup Phone Pairing. • When prompted, after the voice on beep, say Pair a Phone.
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dial by Saying a Number • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Dial. • System will prompt you to say the number you want call.
Page 89 Add Names to Your UConnect™ Phonebook NOTE: Adding names to phonebook is recommended when vehicle is not in motion. • Press the “Phone” button to begin. • After the Ready prompt and the following beep, say Phonebook New Entry. • When prompted, say the name of the new entry. Use of long names helps the voice recognition and is recom- mended.
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will then be asked for the name of the phonebook entry that you wish to edit. • Next, choose the number designation (home, work, mobile, or pager) that you wish to edit. •...
Page 91: Phone Call Features
After confirmation, the phonebook entries will be de- leted. Note that only the phonebook in the current language is deleted. Delete All Entries in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt and the following beep, say Phonebook Erase All.
Page 92 92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - No Call Currently in Progress When you receive a call on your cellular phone, the UConnect™ system will interrupt the vehicle audio system, if on, and will ask if you would like to answer the call.
Page 93 Toggling Between Calls If two calls are in progress (one active and one on hold), press the ’Phone’ button until you hear a single beep indicating that the active and hold status of the two calls have switched. Only one call can be placed on hold at one time.
Page 94: Uconnect™ System Features
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Call Continuation Call continuation is progression of a phone call on UConnect™ system after the vehicle ignition key has been switched to off. Call continuation functionality available on the vehicle can be any one of three types: •...
Page 95 Emergency Assistance If you are in an emergency and the mobile phone is reachable: • Pick up the phone and manually dial the emergency number for your area. If the phone is not reachable and the UConnect™ system is operational, you may reach the emergency number as follows: •...
Page 96 96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Please refer to the 24-Hour Towing Assistance coverage details in the DaimlerChrysler Corporation 24-Hour Towing Assistance Program Guide. Paging To learn how to page, refer to section Working with Automated Systems. Paging works properly except for pagers of certain companies which time-out a little too soon to work properly with the UConnect™...
Page 97 Barge In - Overriding Prompts The ’Voice Recognition’ button can be used when you wish to skip part of a prompt and issue your voice recognition command immediately. For example, if a prompt is playing Would you like to pair a phone, clear a , you could press the ’Voice Recognition’...
Page 98: Advanced Phone Connectivity
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE may feel that the call did not go through even though the call is in progress. Once your call is answered, you will hear the audio. Mute/Un-mute (Mute off) When you mute the UConnect™ system, you will still be able to hear the conversation coming from the other party, but the other party will not be able to hear you.
Page 99 If you would like to connect or disconnect the Blue- tooth™ connection between a UConnect™ paired cellular phone and the UConnect™ system, follow the instruction described in your cellular phone user’s manual. List Paired Cellular Phone Names • Press the ’Phone’ button to begin. •...
Page 100: Things You Should Know About Your Uconnect™ System
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone call. If the selected phone is not available, the UCon- nect™ system will return to using the highest priority phone present in or near (approximately with in 30 feet) the vehicle.
Page 101 • low road noise, • smooth road surface, • fully closed windows, • dry weather condition. • Even though the system is designed for users speaking in North American English and Spanish accents, the system may not always work for some. •...
Page 102 102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • dry weather condition. • Operation from driver seat. • Performance, such as, audio clarity, echo. and loud- ness to a large degree, rely on the phone and network, and not the UConnect™ system. •...
Page 103 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103...
Page 104 104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 105 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105...
Page 106: Seats
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE North American English Primary Alternate(s) Zero Add location Add new All of them Confirmation prompts Confirmations prompts Delete a name Delete Language Select language List names List all List paired phones List phones Pager Beeper Phone pairing...
Page 107: 40-20-40 Front Seat
40-20-40 Front Seat Manual Forward and Rearward Adjustment As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Page 108: Reclining Seats
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle, as shown, to release the seat back and adjust for comfort. Seat Recliner Handle WARNING! You can be seriously, even fatally, injured riding in a seat with the seatback reclined.
Page 109: Manual Rotary Lumbar Support Adjustment - If Equipped
To lower the head restraint, push in the button and then push down on the head restraint. Head Restraint Adjustment UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar (lower back) support.
Page 110: Power Seats - If Equipped
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. Power Seat Control Location...
Page 111 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move- ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi- tion.
Page 112: Heated Seats - If Equipped
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls. The engine must be running for the heated seats to operate. Heated Seat Switches Each heated seat switch has two settings (HI and LOW).
Page 113: To Open And Close The Hood
TO OPEN AND CLOSE THE HOOD To open the hood, two latches must be released. First pull the hood release lever located below the steering wheel at the base of the instrument panel. Once the hood is released you must reach into the opening beneath the center of the grille and push up the latch to release the safety catch before raising the hood.
Page 114: Lights
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision. Be sure all hood latches are latched fully before driving. LIGHTS Interior Lights Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating...
Page 115: Battery Saver
turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the Party mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
Page 116: Headlamp Delay - If Equipped
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
Page 117: Daytime Running Lights (Canada And Fleet Vehicles Only)
Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.
Page 118: Cargo Light
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
Page 119: Passing Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or...
Page 120: Windshield Wipers
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 121: Windshield Washers
The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
Page 122: Tilt Steering Column
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Release the lever to lock the column firmly in place.
Page 123: Driver Adjustable Pedals - If Equipped
DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 124: Electronic Speed Control - If Equipped
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 125: To Set At A Desired Speed
To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed control without erasing the memory.
Page 126: To Accelerate For Passing
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while the speed control is on, press and hold the DECEL button. Release the button when the desired speed is reached, and the new speed will be set. To Accelerate For Passing Depress the accelerator as you would normally.
Page 127: Overhead Console- If Equipped
OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) — If Equipped • Universal Garage Door Opener — If Equipped UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 128: Overhead Console With Compass/Temperature Mini-Trip Computer - If Equipped
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/ TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 129: Reset Button
RESET Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 Global Reset If the RESET button is pressed twice within 2 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays.
Page 130: Average Fuel Economy (Avg Eco)
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is...
Page 131: Trip Odometer (Odo)
Trip Odometer (ODO) This display shows the distance traveled since the last reset. Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing.
Page 132: Automatic Compass Calibration
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Even if the display still reads a few degrees above 32°F ( 0°C), the road surface may be icy, particularly in woods or on bridges. Drive carefully under such conditions to prevent an accident and possible per- sonal injury or property damage.
Page 133 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 Compass Variance is the difference between magnetic north and geographic north. In some areas of the country, the difference between magnetic and geographic north is great enough to cause the compass to give false readings. If this occurs, the compass variance must be set according to the Compass Variance Map.
Page 134: Outside Temperature
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 135 For additional information on HomeLink , call 1–800– 355–3515, or on the internet at www.homelink.com. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 WARNING! A moving garage door can cause injury to people and pets in the path of the door. People or pets could be seriously or fatally injured.
Page 136: Programming Homelink
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 137 WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 138: Canadian Programming/Gate Programming
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener).
Page 139: Using Homelink
If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the cycling process to prevent possible overheating.
Page 140: Reprogramming A Single Homelink Button
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. DO NOT release the button. 2.
Page 141: Opening Sunroof - Express
WARNING! • Never leave children in a vehicle, with the keys in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch. Such entrapment may result in serious injury or death. •...
Page 142: Pinch Protect Override
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE sunroof will automatically retract. Remove the obstruc- tion if this occurs. Next, press the switch forward and release to Express Close. Pinch Protect Override If a known obstruction (ice, debris, etc.) prevents closing, press the switch forward and hold for two seconds after the reversal occurs.
Page 143: Sunroof Maintenance
Sunroof Maintenance Use only a non-abrasive cleaner and a soft cloth to clean the glass panel. Ignition Off Operation The power sunroof switches remain active for 10 minutes after the ignition switch has been turned off. Opening either front door will cancel this feature. Sunroof Fully Closed Press the switch forward and release to ensure that the sunroof is fully closed.
Page 144: Cigar Lighter And Ash Receiver
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Electrical Outlet Use With Engine Off • Many accessories that can be plugged in draw power from the vehicle’s battery, even when not in use (i.e. cellular phones, etc.). Eventually, if plugged in long enough, the vehicle’s battery will discharge sufficiently to degrade battery life and/or prevent engine starting.
Page 145: Cupholders
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 CUPHOLDERS Front Instrument Panel Cupholders — Automatic Transmission Only Your new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
Page 146: Rear Cupholder - Quad Cab - If Equipped
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To secure the cup, place the cup to be held into one of the cup wells and then push the cupholder arm toward the cup until it is held stable. Cupholders with Automatic Rear Cupholder —...
Page 147: Storage
STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover. Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 configure the storage area into compartments.
Page 148: Storage And Seats - If Equipped
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 149 WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
Page 150 150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under the Seat 1.
Page 151: Pickup Box
4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from your dealer.
Page 152 152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
Page 153: Slide-In Campers
There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 154 154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed.
Page 155 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers” should extend beyond the overhanging camper compartment and be free of leaks.
Page 157 UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....160 Instrument Cluster ..... . 161 Instrument Cluster Description .
Page 158 158 UNDERSTANDING YOUR INSTRUMENT PANEL Tuning ......177 Radio Data System (RDS) ....178 PTY (Program Type) Button .
Page 159 Time Button ......186 Scan Button ......186 CD Changer Control Capability —...
Page 160: 160 Understanding Your Instrument Panel
160 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 161: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 161 INSTRUMENT CLUSTER...
Page 162: Instrument Cluster Description
162 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 163 the pointer moves to either extreme left or right and remains there during normal driving, the electrical sys- tem should be serviced. NOTE: If the gauge pointer moves to either extreme of the gauge, the “Check Gages” indicator will illuminate and a single chime will sound.
Page 164 164 UNDERSTANDING YOUR INSTRUMENT PANEL unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to Enhanced Driver Seat Belt Re- minder System (BeltAlert™) in the Occupant Restraints section for more information.
Page 165 light will come on when the ignition key is turned to the ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
Page 166 166 UNDERSTANDING YOUR INSTRUMENT PANEL 14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set. The security light will also come on for about two seconds when the ignition is first turned ON.
Page 167 Acceleration which causes the rear wheels to slip for a period of time may result in the red brake light illumi- nating and a brake switch code being set on ABS equipped vehicles. Depressing the brake pedal should extinguish the red brake light. 19.
Page 168 168 UNDERSTANDING YOUR INSTRUMENT PANEL 21. LAMP OUT Light The LAMP OUT indicator in the instrument cluster alerts the driver if a defective bulb or wiring circuit is detected for headlamps, turn signal lamps, and stop lamps. 22. TOW/HAUL (Automatic Transmissions Only) The TOW/HAUL button is located at the end of the gear shift lever.
Page 169 reserve fuel capacity, which corresponds to approxi- mately 8% of tank volume. This reserve capacity was put in place to prevent the likelihood of customers running out of fuel when operating at maximum load conditions in areas where there aren’t many gas stations. (See page 130 for more information.) Ram fuel tank volumes are as follows: •...
Page 170: Electronic Digital Clock
170 UNDERSTANDING YOUR INSTRUMENT PANEL ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the “ON” or “ACC”...
Page 171: Radio Operation
Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL and press and release that button. If a button is not selected within 5 seconds after pressing the SET button, the station will continue to play but will not be locked into push-button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
Page 173: Mode Button
AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player, CD changer, or the Satellite Radio (if equipped).
Page 174 174 UNDERSTANDING YOUR INSTRUMENT PANEL The SEEK symbol appears on the display when Music Search is in operation. Music Search shuts off automati- cally when a selection has been located. Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections.
Page 175: Cd Changer Control Capability - If Equipped
CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual. CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically.
Page 177: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls
SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS RAZ Radio Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 178: Radio Data System (Rds)
178 UNDERSTANDING YOUR INSTRUMENT PANEL Radio Data System (RDS) The Radio Data System allows radio broadcasting sta- tions to send data signals on a subcarrier frequency which is added to the stereo signal. RDS was developed to give FM receivers user-friendly features, such as Program Service name (PS) and Program Type (PTY).
Page 179 Program Type Radio Display Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk Talk Top 40 Top 40 Weather...
Page 180: Balance
180 UNDERSTANDING YOUR INSTRUMENT PANEL Balance The Balance control adjusts the left-to-right speaker bal- ance. Push in the button and it will pop out. Adjust the balance and push the button back in. The balance will be displayed and continuously updated while the button is turned.
Page 181: To Set The Radio Push-Button Memory
To Set The Radio Push-button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. SET 1 will show in the display window. Select the push-button you wish to lock onto this station and press and release that button.
Page 182: Fast Forward (Ff)
182 UNDERSTANDING YOUR INSTRUMENT PANEL Press the SEEK button up or down to move the track number to skip forward or backward 1 to 6 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward (FF) Press the FF button up momentarily to advance the tape in the direction that it is playing.
Page 183: Pinch Roller Release
Pinch Roller Release If ignition power or the radio ON/OFF switch are turned off, the pinch roller will automatically retract to protect the tape from any damage. When power is restored to the tape player, the pinch roller will automatically reengage and the tape will resume play.
Page 184: Seek Button
184 UNDERSTANDING YOUR INSTRUMENT PANEL If the volume control is ON, the unit will switch from radio to CD mode and begin to play. The display will show the track number and index time in minutes and seconds. Play will begin at the start of track one. NOTE: •...
Page 185: Ff/Tune/Rw
FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Program Button 4 (Random Play) Press this button while the CD is playing to activate Random Play.
Page 186: Time Button
186 UNDERSTANDING YOUR INSTRUMENT PANEL Time Button Press this button to change the display from elapsed CD playing time to time of day. Scan Button Press this button to play the first 10 seconds of each track. To stop the scan function, press the button a second time. CD Changer Control Capability —...
Page 187: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
CD Diagnostic Indicators When driving over a very rough road, the CD player may skip momentarily. Skipping will not damage the disc or the player, and play will resume automatically. As a safeguard and to protect your CD player, one of the following warning symbols may appear on your display.
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is supplied through the ignition switch. It must be in the ON or ACC position to operate the radio. Seek Press and release the SEEK button to search for the next station in either the AM or FM mode.
Page 189 Audio The audio button controls the BASS, TREBLE, BAL- ANCE, and FADE. Press the AUDIO button and BASS will be displayed. Press the SEEK + or SEEK – to increase or decrease the Bass tones. Press the AUDIO button a second time and TREB will be displayed.
Page 190: Cd Player Operation
190 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Changes or modifications not expressively ap- proved by the party responsible for compliance could void the user’s authority to operate the equipment. CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate.
Page 191: Cd Changer Control Capability - If Equipped
If you do not remove the disc within 15 seconds, it will be reloaded. The unit will continue in radio mode. The disc can be ejected with the radio and ignition OFF (except on convertibles). FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Disc Up/Program Button 1 Press the DISC up (button 1) button to play the next available disc. Disc Down/Program Button 5 Press the DISC down (button 5) button to play the previous disc.
Page 193: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio. Mode Press the MODE button repeatedly to select between AM, FM, the CD changer and Sirius Satellite Radio™...
Page 195 and release that button. If a button is not selected within 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
Page 196: Cd Player Operation
196 UNDERSTANDING YOUR INSTRUMENT PANEL General Information This radio complies with Part 15 of FCC rules and with RSS-210 of Industry Canada. Operation is subject to the following conditions: 1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired opera- tion.
Page 197 show the disc number, the track number, and index time in minutes and seconds. Play will begin at the start of track 1. LOAD/ EJT — Load Press the LOAD/ EJT button and the button with the corresponding number where the CD is being loaded. After the radio displays “load”...
Page 198 198 UNDERSTANDING YOUR INSTRUMENT PANEL FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play — SET / RND Press the RND button while the CD is playing to activate Random Play.
Page 199 Program Type Radio Display Nostalgia Nostalga Oldies Oldies Personality Persnlty Public Public Rhythm and Blues R & B Religious Music Rel Musc Religious Talk Rel Talk Rock Rock Soft Soft Soft Rock Soft Rck Soft Rhythm and Blues Soft R&B Sports Sports Talk...
Page 200 200 UNDERSTANDING YOUR INSTRUMENT PANEL Time Press the TIME button to change the display from elapsed CD playing time to time of day. Operating Instructions - Satellite Radio Mode (If Equipped) Refer to the Satellite Radio section of the Owner’s Manual.
Page 201: Remote Sound System Controls - If Equipped
REMOTE SOUND SYSTEM CONTROLS — IF EQUIPPED The remote sound system controls are located on the rear surface of the steering wheel. Reach behind the wheel to access the switches. The right hand control is a rocker type switch with a button in the center.
Page 202: Tape Player
202 UNDERSTANDING YOUR INSTRUMENT PANEL Tape Player Pressing the top of the switch once will go to the next selection on the cassette. Pressing the bottom of the switch once will go to the beginning of the current selection or to the beginning of the previous selection if it is within the first 5 seconds of the current selection.
Page 203: Compact Disc Maintenance
5. A loose tape should be corrected before use. To rewind a loose tape, insert the eraser end of a pencil into the tape drive gear and twist the pencil in the required directions. Maintain your cassette tape player. The head and capstan shaft in the cassette player can pick up dirt or tape deposits each time a cassette is played.
Page 204: Radio Operation And Cellular Phones
204 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If you experience difficulty in playing a particu- lar disc, it may be damaged, oversized, or have theft protection encoding. Try a known good disc before considering disc player service. RADIO OPERATION AND CELLULAR PHONES Under certain conditions, the operation of a cellular phone in your vehicle can cause erratic or noisy perfor- mance from your radio.
Page 205: Heater Only - Fleet Vehicles
Heater Only — Fleet Vehicles The mode control (at the right of the control panel) can be set in any of the following positions: UNDERSTANDING YOUR INSTRUMENT PANEL 205 NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes.
Page 206 206 UNDERSTANDING YOUR INSTRUMENT PANEL Bi-Level Outside air flows through the outlets located in the instrument panel and at the floor. Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel.
Page 207: Air Conditioning-If Equipped
Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
Page 208 208 UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air condition- ing off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
Page 209 Floor Outside air flows primarily through the floor out- lets located under the instrument panel. Outside air flows in equal proportions through the floor and defroster outlets, and the air conditioning may be on. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel, and the air...
Page 210: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
210 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
Page 211: Air Conditioning With Dual Zone Temperature Control - If Equipped
turn off after activation, when 15 minutes have elapsed. To reactivate, simply press the button again. Air Conditioning with Dual Zone Temperature Control — If Equipped With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle.
Page 212 212 UNDERSTANDING YOUR INSTRUMENT PANEL A/C Pushbutton With the fan control in the ON posi- tion, pushing the A/C button turns on the air conditioning compressor. An indicator light on the button shows that the Air Conditioning compressor is on. Conditioned air is now directed through the mode outlets selected.
Page 213 Bi-Level Air flows through the outlets located in the instru- ment panel and those located on the floor. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions.
Page 214 214 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 215: Operating Tips
edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time.
Page 216 216 UNDERSTANDING YOUR INSTRUMENT PANEL speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
Page 217: Operating Tips Chart
UNDERSTANDING YOUR INSTRUMENT PANEL 217 Operating Tips Chart...
Page 219 STARTING AND OPERATING CONTENTS Ignition/Starter Switch ....223 Lock ......223 Off .
Page 220 220 STARTING AND OPERATING Operating Precautions ....235 Cooling System Tips — Automatic Transmission ......236 Transmission Shifting .
Page 221 Tire Inflation Pressures ....269 Radial-Ply Tires ..... . 271 Compact Spare Tire —...
Page 222 222 STARTING AND OPERATING Trailer Towing Information (Maximum Trailer Weight Ratings) ..... . 295 Trailer Towing Mirrors — If Equipped ..296 Cooling System Tips —...
Page 223: Ignition/Starter Switch
IGNITION/STARTER SWITCH LOCK Locks the automatic transmission shift control into the PARK position. It also engages the steering wheel lock (if equipped) when the steering wheel is turned. STARTING AND OPERATING 223 NOTE: This vehicle is equipped with a transmission shift interlocking system.
Page 224: Acc
224 STARTING AND OPERATING Allows the electrical accessories to be used when the engine is not running. Manual Transmission Key Release Button To remove the key on vehicles equipped with manual transmissions, turn the key to the Lock position and press the button to remove the ignition key.
Page 225: Starting And Operating 225
• A heated intake air system both improves engine starting and reduces the amount of white smoke generated by a warming engine. Normal Starting Procedure — Engine Manifold AirTemperature Above 66°F (19°C) Observe the Instrument Panel Cluster lights when start- ing the engine.
Page 226: Starting Procedure - Engine Manifold Air
226 STARTING AND OPERATING CAUTION! Do not crank engine for more than 15 seconds at a time as starter motor damage may result. Turn key to OFF and wait at least two minutes before trying again. 5. When the engine starts, release the key. 6.
Page 227 • After the WAIT TO START light goes off, turn the ignition key to START. Do not press the accelerator during starting. • Check to see that there is oil pressure. • Allow the engine to idle at fast idle for about three minutes until the manifold heaters have completed the post-heat cycle.
Page 228 228 STARTING AND OPERATING NOTE: Excessive white smoke and poor engine perfor- mance will result if manifold heaters are not recycled. • Heat generated by the manifold heaters dissipates rapidly in a cold engine. If more than two minutes pass between the time the WAIT TO START light goes OFF and the engine is started, recycle the manifold heaters by turning the ignition OFF for at least 5 seconds and then back ON.
Page 229: Starting Fluids
4. Repeat the procedure if the engine does not start. WARNING! Do not open the high pressure fuel system with the engine running. Engine operation causes high fuel pressure. High pressure fuel spray can cause serious injury or death. NOTE: The engine may run rough until the air is forced from all the fuel lines.
Page 230: Normal Operation
230 STARTING AND OPERATING WARNING! Do not leave children or animals inside parked vehicles in hot weather. Interior heat build up may cause serious injury or death. NORMAL OPERATION Observe the following when the engine is operating. • All message center lights are off. •...
Page 231: Cold Weather Precautions
Cold Weather Precautions Operation in ambient temperature below 32°F (0°C) may require special considerations. The following charts sug- gest these options: Fuel Operating Range *No. 1 diesel fuel should only be used where extended arctic conditions (-10°F/-23°C) exist. NOTE: • Use of Climatized Diesel Fuel or Number 1 Diesel Fuel results in a noticeable decrease in fuel economy.
Page 232 232 STARTING AND OPERATING The block heater must be plugged in at least one hour to have an adequate warming effect on the coolant. WARNING! Remember to disconnect the cord before driving. Damage to the 110–115 volt electrical cord could cause electrocution.
Page 233: Engine Idling - In Cold Weather
Arctic Operation Where there are no provisions to keep the engine warm when it is operating in ambient temperatures consistently below (-10°F/-23°C), use 5W-40 synthetic engine oil and fuel that meets the requirements in Section 7, “Mainte- nance Procedures,” Engine Oil Selection. Engine Warm-Up Avoid full throttle operation when the engine is cold.
Page 234: Stopping The Engine
234 STARTING AND OPERATING NOTE: • If ambient temperatures are low and the coolant temperature is below 200°F (93°C), the engine idle speed will slowly increase to 1000 RPM after 2 minutes of idle, if the following conditions are met: •...
Page 235: Engine Speed Control
Driving Turbocharger Load Condition Temperature Stop and Go Empty Cool Stop and Go Medium Highway Medium Warm Speeds City Traffic Maximum GCWR Highway Maximum Speeds GCWR Uphill Grade Maximum GCWR Engine Speed Control Idle Time (min.) Before Engine Shutdown Less than Prevent overspeeding the engine going down hill.
Page 236: Cooling System Tips - Automatic Transmission
236 STARTING AND OPERATING Avoid Low Coolant Temperature Operation Continual operation at low coolant temperature below the normal range on the gauge (140°F/60°C) can be harmful to the engine. Low coolant temperature can cause incomplete combustion which allows carbon and varnish to form on piston rings and injector nozzles.
Page 237: Transmission Shifting
Do Not Operate The Engine With Failed Parts Practically all failures give some warning before the parts fail. Be on the alert for changes in performance, sounds, and visual evidence that the engine requires service. Some important clues are: • engine misfiring or vibrating severely •...
Page 238 238 STARTING AND OPERATING “P” Park This gear position supplements the parking brake by locking the transmission. The engine can be started in this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range.
Page 239 “N” Neutral Shift to Neutral when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range. Set the parking brake if you must leave the vehicle. “D” Drive This position provides all forward gears, including 3rd gear direct and 4th or 5th (if equipped) gear overdrive (see Overdrive Operation).
Page 240 240 STARTING AND OPERATING When To Use “TOW/HAUL” Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “TOW/HAUL” button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
Page 241: Manual Transmission - 6-Speed - If Equipped
Torque Converter Clutch A feature, designed to improve fuel economy, has been included in the automatic transmission on your vehicle. A clutch within the torque converter engages automati- cally at calibrated speeds. This may result in a slightly different feeling or response during normal operation in high gear.
Page 242 242 STARTING AND OPERATING Fully depress the clutch pedal before shifting gears. As you release the clutch pedal, lightly depress the accelera- tor pedal. When launching a stationary vehicle, keep the engine speed low until the clutch is fully engaged. This transmission has a “creeper”...
Page 243: Four-Wheel- Drive Operation - If Equipped
FOUR-WHEEL- DRIVE OPERATION — IF EQUIPPED • Four-Wheel-Drive Dodge Ram Trucks are equipped with either a Manually Shifted transfer case or an Electronically Shifted transfer case. See the operating instructions for your transfer case, located within this section.
Page 244 244 STARTING AND OPERATING The 4-wheel-drive light (4WD), located in the instrument cluster, alerts the driver that the vehicle is in 4-wheel drive and that the front and rear driveshafts are locked together. This light illuminates when the transfer case is shifted to either the 4H or 4L positions.
Page 245 WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 246: Shifting Procedure - Manually Shifted Transfer Case
246 STARTING AND OPERATING Shifting Procedure - Manually Shifted Transfer Case 2H ⇔ 4H Shifting between 2H and 4H can be made with the vehicle stopped or in motion. If the vehicle is in motion, shifts can be made up to 55 mph (88 km/h). With the vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after completing the shift.
Page 247: Transfer Case Reminder Light
NOTE: Shifting into or out of 4L is possible with the vehicle completely stopped, however difficulty may oc- cur due to the mating clutch teeth not being properly aligned. Several attempts may be required for clutch teeth alignment and shift completion to occur. The pre- ferred method is with the vehicle rolling 2 to 3 mph (3 to 5 km/h).
Page 248 248 STARTING AND OPERATING position - see Shifting Procedure section for specific shifting instructions. The 4HI and 4LO positions are designed for loose, slippery road surfaces only. Driving in the 4HI and 4LO positions on dry hard surfaced roads may cause increased tire wear and damage to the driv- eline components.
Page 249 NOTE: Before retrying a selection, make certain that all the necessary requirements for selecting a new transfer case position have been met. To retry the selection, turn the control knob back to the current position, wait five (5) seconds, and retry selection. To find the shift require- ments, refer to the Shifting Procedure for your transfer case, located in this section of the owner’s manual.
Page 250 250 STARTING AND OPERATING When operating your vehicle in 4LO, the engine speed is approximately three times that of the 2WD/AWD or 4HI positions at a given road speed. Take care not to over- speed the engine and do not exceed 25 mph (40 km/h). Proper operation of 4 wheel drive vehicles depends on tires of equal size, type and circumference on each wheel.
Page 251: Shifting Procedure - Electronically Shifted Transfer Case
For additional information on the appropriate use of each transfer case mode position see the information below: 2WD/AWD Rear Wheel Drive High Range - Normal street and highway driving. Dry hard surfaced roads. 4 Wheel Drive High Range - Locks the front and rear driveshafts together.
Page 252 252 STARTING AND OPERATING NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
Page 253 key must be in the ON position with the engine either RUNNING or OFF. This shift cannot be completed if the key is in the accessory position. NOTE: The 4x4 system will not allow shifts between (2WD/AWD)/4HI if the front and/or rear wheels are spinning (no traction).
Page 254: Limited-Slip Differential - If Equipped
254 STARTING AND OPERATING 3. Rotate the transfer case control switch to the desired position. 4. After the desired position indicator light is ON (not flashing), shift transmission back into gear (release clutch on manual transmissions). NOTE: If steps 1 or 2 of either the Preferred or Alternate Procedure are not satisfied prior to attempting the shift or if they no longer are being met while the shift attempt is in process then the desired position indicator light will...
Page 255: Parking Brake
WARNING! On vehicles equipped with a limited-slip differen- tial, never run the engine with one rear wheel off the ground, since the vehicle may drive through the rear wheel remaining on the ground. You could lose control of the vehicle. Care should be taken to avoid sudden accelerations when both rear wheels are on a slippery surface.
Page 256: Brake System
256 STARTING AND OPERATING load on the transmission locking mechanism may make it difficult to move the selector out of PARK. WARNING! • Always fully apply the parking brake when leaving your vehicle, or it may roll and cause damage or injury.
Page 257: Brake Noise
Brake Noise During normal operation of the brake system certain noises may be present from time to time. Occasional groan or squeal noises may occur during normal operation of the brake system which may not be indica- tive of a problem. These noises may be heard at any time the brakes are applied but may be more noticeable during the first few brake applications in the morning.
Page 258 258 STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 259: Power Steering
ABS Warning Light The Anti-lock Brake System includes an amber warning light, located in the instrument cluster. When the light is illuminated, the Anti-lock Brake System is not function- ing. The system reverts to standard non-anti-lock brakes. WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident.
Page 260: Tire Safety Information
260 STARTING AND OPERATING TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. • European Metric tire sizing is based on European design standards.
Page 261 Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm) 65 = Aspect Ratio in Percent (%)
Page 262 262 STARTING AND OPERATING Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions.
Page 263: Tire Identification Number (Tin)
Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire. DOT = Department of Transportation —This symbol certifies that the tire is in compliance with the U.S.
Page 264: Tire Loading And Tire Pressure
264 STARTING AND OPERATING Tire Loading and Tire Pressure Tire Placard Location NOTE: The proper cold tire inflation pressure for pas- senger cars is listed on either the face of the driver’s door or the driver’s side “B” pillar. For vehicles other than passenger cars, the cold tire inflation pressures are listed on either the shutface of the driver’s door, the “B”...
Page 265 Tire and Loading Information Placard Tire and Loading Information This placard tells you important information about the: 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle 4) the cold tire inflation pressures for the front, rear and spare tires.
Page 266 266 STARTING AND OPERATING combined weight of occupants, cargo/luggage and trailer tongue weight (if applicable) should never exceed the weight referenced here. Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard.
Page 267 STARTING AND OPERATING 267...
Page 268: Tires-General Information
268 STARTING AND OPERATING WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 269: Tire Inflation Pressures
2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption. 3.
Page 270 270 STARTING AND OPERATING check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are under inflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 271: Radial-Ply Tires
Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 272: Compact Spare Tire - If Equipped
272 STARTING AND OPERATING Compact Spare Tire — If Equipped The compact spare is for temporary emergency use with radial tires. It is engineered to be used on your style vehicle only. Since this tire has limited tread life, the original tire should be repaired (or replaced) and rein- stalled at the first opportunity.
Page 273: Limited Use Spare - If Equipped
Limited Use Spare — If Equipped The limited use spare tire is for temporary emergency use on your vehicle. This tire is identified by a limited use spare tire warning label located on the limited use spare tire and wheel assembly. This tire may look like the original equipped tire on the front or rear axle of your vehicle, but it is not.
Page 274: Tread Wear Indicators
274 STARTING AND OPERATING WARNING! Fast spinning tires can be dangerous. Forces gener- ated by excessive wheel speeds may cause tire dam- age or failure. A tire could explode and injure someone. Do not spin your vehicle’s wheels faster than 35 mph (55 km/h) when you are stuck. And don’t let anyone near a spinning wheel, no matter what the speed.
Page 275: Replacement Tires
Replacement Tires The tires on your new vehicle provide a balance of many characteristics. They should be inspected regularly for wear and correct cold tire inflation pressure. The manu- facturer strongly recommends that you use tires equiva- lent to the originals in size, quality and performance when replacement is needed (see the paragraph on tread wear indicators).
Page 276: Alignment And Balance
276 STARTING AND OPERATING CAUTION! Replacing original tires with tires of a different size may result in false speedometer and odometer read- ings. Alignment And Balance Poor suspension alignment may result in: • Fast tire wear. • Uneven tire wear, such as feathering and one-sided wear.
Page 277 CAUTION! To avoid damage to your vehicle, tires or chains, observe the following precautions: • Because of limited chain clearance between tires and other suspension components, it is important that only chains in good condition are used. Broken chains can cause serious vehicle damage.
Page 278: Snow Tires
278 STARTING AND OPERATING CAUTION! Do not use tire chains on 4x4 Ram trucks equipped with P265/70R17, LT275/70R17 tires. There may not be adequate clearance for the chains and you are risking structural or body damage to your vehicle. Do not use tire chains on the 4X2 front wheels of 2500/3500 SRW (Single Rear Wheels) equipped with LT245/70R17, LT265/70R17 tires or 4X4 front tires of Ram Trucks equipped with LT265/70R17tires.
Page 279: Tire Rotation Recommendations
TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
Page 280: Dual Rear Wheels
280 STARTING AND OPERATING Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. CAUTION! 3500 Dual Rear Tires have only one approved direc- tion of rotation.
Page 281: Engine Runaway
STARTING AND OPERATING 281 FUEL REQUIREMENTS Use good quality diesel fuel from a reputable supplier in your Dodge truck. For most year-round service, No. 2 diesel fuel meeting ASTM specification D-975 will pro- vide good performance. If the vehicle is exposed to extreme cold (below 20°F or -7°C), or is required to...
Page 282: Adding Fuel
282 STARTING AND OPERATING Diesel fuel is seldom completely free of water. To prevent fuel system trouble, drain the accumulated water from the fuel/water separator using the fuel/water separator drain provided. If you buy good quality fuel and follow the cold weather advice above, fuel conditioners should not be required in your vehicle.
Page 283 Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 284: Bulk Fuel Storage
NOTE: A maximum blend of 5% biodiesel may be used with your Cummins Diesel equipped Dodge Ram Truck. NOTE: In addition, commercially available fuel addi- tives are not necessary for the proper operation of your Cummins Diesel equipped Dodge Ram Truck.
Page 285 Number 2 Diesel Fuel Specifications Fuel Properties - No. 2 - Diesel Reference Viscosity - 1.9 to 4.1 centistokes (ASTM D-445) Cetane Number - 40 min. (ASTM D613) Sulfur Content -.05% by weight (ASTM D-2622) Water & Sediment - less than (ASTM D-2709) 0.05 % by volume Carbon Residue - Less...
Page 286: Vehicle Loading
286 STARTING AND OPERATING VEHICLE LOADING Certification Label As required by National Highway Traffic Safety Admin- istration Regulations, your vehicle has a certification label affixed to the driver’s side door or pillar. This label contains the month and year of manufacture, Gross Vehicle Weight Rating (GVWR), Gross Axle Weight Rating (GAWR) front and rear, and Vehicle Identification Number (VIN).
Page 287 Tire Size This is the minimum allowable tire size for your vehicle. Replacement tires must be equal to the load capacity of this tire size. Rim Size This is the rim size that is appropriate for the tire size listed. Inflation Pressure This is the cold tire inflation pressure for your vehicle for all loading conditions up to full GAWR.
Page 288 288 STARTING AND OPERATING CAUTION! Do not load your vehicle any heavier than the GVWR or the maximum front and rear GAWR. If you do, parts on your vehicle can break, or it can change the way your vehicle handles. This could cause you to lose control.
Page 289: Trailer Towing
TRAILER TOWING All Dodge Ram Pickup trucks are intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be factory equipped for safe towing of trailers weighing over 2,000 lbs (907 kg) with the optional Trailer Tow Prep Package.
Page 290 290 STARTING AND OPERATING CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer. Doing so may damage your vehicle. • When first towing a trailer, limit your speed to 50 mph (80 km/h) during the first 500 miles (805 km) of towing.
Page 291: Axle Lubricant And Trailer Towing
must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross Vehicle Weight Rating. WARNING! Improper towing can lead to an injury accident. Follow these guidelines to make your trailer towing as safe as possible: Axle Lubricant and Trailer Towing 2500/3500 Models...
Page 292: Trailer Towing - Hitches
292 STARTING AND OPERATING under the bumper. This connector contains the follow- ing vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/turn lamp, and ground. With the optional Trailer Tow Prep package a 7-way connector is provided with the following additional circuits: backup lamp, trailer battery and electric brake.
Page 293: Connecting Trailer Lighting And Electric Trailer Brakes
A frame mounted hitch of up to Class IV rating, as rated by the hitch manufacturer, is supplied as part of the trailer tow prep package. With a Class IV Hitch, you can tow a trailer with a Gross Trailer Weight of up to 12,000 lbs (5 443 kg) maximum depending on your vehicle equipment.
Page 294: Trailer Weight And Trailer Tongue Weight
294 STARTING AND OPERATING CAUTION! Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits. Use an approved wiring harness con- nector on the trailer. Trailer Weight and Trailer Tongue Weight Gross Trailer Weight (GTW) means the weight of the trailer plus the weight of all cargo, consumables and equipment loaded on the trailer when in actual under-...
Page 295: Trailer Towing Information (Maximum Trailer Weight Ratings)
4. GAWR ratings Trailer Towing Information (Maximum Trailer Weight Ratings) Trailer Towing Guide NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website address: http:// www.dodge.com/towing. In Canada, refer to the following website address: http:// www.dodge.ca.
Page 296: Trailer Towing Mirrors - If Equipped
296 STARTING AND OPERATING Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped Out or In).
Page 297: Cooling System Tips - Trailer Towing
STARTING AND OPERATING 297 Cooling System Tips — Trailer Towing To reduce potential for engine and transmission over- heating, take the following actions in high ambient temperatures: • City Driving— when stopped, put the transmission in N (Neutral) and increase the engine idle speed. •...
Page 298: Automatic Transmission Oil Temperature Warning Light
Snowplow Prep Packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow. NOTE: Before installation of a snowplow it is highly recommended that the owner / installer obtain and follow the recommendations contained within the Dodge...
Page 299: Before Plowing
• Check that snowplow lighting is connected and func- tioning properly. Snowplow Prep Package Model Availability For Information about snowplow applications visit www.dodge.com or refer to the 2005 Dodge Truck Body Builders Guide. 1. The maximum number of occupants in the truck should not exceed two.
Page 300: Over The Road Operation With Snowplow Attached
300 STARTING AND OPERATING 2. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 3. The snowplow prep packages are not available with the Sport Package. 4. Cargo capacity will be reduced by the addition of options or passengers, etc.
Page 301: Methods For Removing Snow
Methods For Removing Snow Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed. The operator should be familiar with the area and surface to be cleaned. Reduce speed and use extreme caution when plowing unfamiliar areas or under poor visibility.
Page 302: Recreational Towing - 4 Wheel Drive Vehicles (Behind Motorhome, Etc.)
302 STARTING AND OPERATING • Operate with transfer case in 4L when plowing small or congested areas where speeds are not likely to exceed 15 mph (24 km/h). At higher speeds operate in • Vehicles with 48RE transmissions should use 4L range when plowing deep or heavy snow for extended periods of time to avoid transmission overheating.
Page 303: Recreational Towing Procedure - Manual
CAUTION! Internal damage to the transfer case will occur if a front or rear wheel lift is used when recreational towing. NOTE: Both the Manual Shift and Electronic Shift transfer cases must be shifted into Neutral (N) for recreational towing. Automatic transmissions must be placed in P (Park) position for recreational towing.
Page 304 304 STARTING AND OPERATING 5. Shift transfer case lever into N (NEUTRAL). 6. Start the engine. 7. Shift automatic transmission into Reverse (R). 8. Release brake pedal for five seconds and ensure that there is no vehicle movement. 9. Repeat steps 7 and 8 with the transmission in Drive (D).
Page 305: Returning To Normal Operation - Manual Shift Transfer Case
Returning to Normal Operation — Manual Shift Transfer Case Use the following procedure to prepare your vehicle for normal usage: 1. Bring the vehicle to a complete stop. 2. Shut OFF the engine. 3. Depress the brake pedal. 4. Shift automatic transmission to N (NEUTRAL), or depress the clutch on manual transmissions.
Page 306: Recreational Towing Procedure - Electronic
306 STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts.
Page 307 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement. 11.
Page 308: Returning To Normal Operation - Electronic Shift Transfer Case
308 STARTING AND OPERATING CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P).
Page 309 during the 1 second time, then all of the mode position indicator lights will flash continuously until all require- ments are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
Page 310: Driving Off-Road
310 STARTING AND OPERATING CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts.
Page 311: Traction
If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for im- pacted material. Impacted foreign material can cause a wheel imbalance. Removing the foreign material from the wheels will correct the situation. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road surface.
Page 313 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Lights ....314 Adding Fuel — 24–Valve Cummins Turbo Diesel ....... 315 Jack Location .
Page 314: 314 What To Do In Emergencies
314 WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency.
Page 315: Adding Fuel - 24-Valve Cummins Turbo Diesel
You may try priming as described below. However, if the engine will not start, refer to the fuel priming procedure in the Service Manual or have the vehicle towed to an authorized Dodge dealer. WHAT TO DO IN EMERGENCIES 315 WARNING! Do not open the high pressure fuel system with the engine running.
Page 316: Jack Location
316 WHAT TO DO IN EMERGENCIES 4. Repeat the procedure if the engine does not start. CAUTION! Do not engage the starter motor for more than 15 seconds at a time. Allow two minutes between the cranking intervals. NOTE: The engine may run rough until the air is forced from all the fuel lines.
Page 317: Changing A Flat Tire
WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable sup- ports are placed under the vehicle as a safety mea- sure.
Page 318: Tire Changing Procedure
318 WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
Page 319 Preparations Park the vehicle on a firm level surface, avoiding ice or slippery areas. Set the parking brake and place the gear selector in PARK (automatic transmission) or REVERSE (manual transmission). On four-wheel drive vehicles, shift the transfer case to the “4L” position. WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic.
Page 320 320 WHAT TO DO IN EMERGENCIES Instructions WARNING! Carefully follow these tire changing warnings to help prevent personal injury or damage to your vehicle: • Always park on a firm, level surface as far from the edge of the roadway as possible before raising the vehicle.
Page 321 WHAT TO DO IN EMERGENCIES 321 Before raising the wheel off the ground, make sure that the jack will not damage surrounding truck parts and adjust the jack position as required. NOTE: If the jack will not lower by turning the dial (thumb wheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack.
Page 322 322 WHAT TO DO IN EMERGENCIES 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface. WARNING! Raising the vehicle higher than necessary can make the vehicle unstable and cause an accident. It could slip off the jack and hurt someone near it.
Page 323 (SRW) models and 145 ft. lbs. (197 N·m) for 3500 dual rear wheel models. If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station. WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle.
Page 324 324 WHAT TO DO IN EMERGENCIES models use the blade on the end of the lug wrench to pry the caps off. The wheel skin can now be removed. You must use the flat end of the lug wrench to pry off the wheel skins.
Page 325 WHAT TO DO IN EMERGENCIES 325 Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device.
Page 326 326 WHAT TO DO IN EMERGENCIES 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 327: Hoisting
Attach the wheel wrench to the extension tube. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 3 or 4 times.
Page 328 328 WHAT TO DO IN EMERGENCIES Your vehicle is equipped with two 12–volt batteries. If it becomes necessary to use a booster battery, with jumper cables, to start a vehicle’s engine because its batteries are discharged, the following procedure should be followed: Set the parking brake and place an automatic transmis- sion in PARK (or NEUTRAL for a manual transmission).
Page 329 WARNING! Do not permit vehicles to touch each other as this could establish a ground connection and personal injury could result. WHAT TO DO IN EMERGENCIES 329 2. Connect one end of the other jumper cable to negative (-) post of booster battery. Connect the other end of the jumper cable to a good ground on the engine block of the vehicle with the discharged battery.
Page 330: With Portable Starting Unit
330 WHAT TO DO IN EMERGENCIES 3. Take care that the clamps from one cable do not inadvertently touch clamps from the other cable. Do not lean over the battery when making connection. The negative connection must provide good electrical con- ductivity and current carrying capacity.
Page 331: Freeing A Stuck Vehicle
CAUTION! It is very important that the starting unit operating voltage does not exceed 12 Volts D.C. or damage to battery, starter motor, alternator, or electrical system may occur. FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion.
Page 332: Towing A Disabled Vehicle
332 WHAT TO DO IN EMERGENCIES WARNING! Stand clear of vehicles when pulling with tow hooks. Tow straps and chains may break, causing serious injury. CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing.
Page 333: 2-Wheel- Drive Vehicles
The manufacturer recommends towing with all wheels OFF the ground. Acceptable methods are to tow vehicle on a flatbed or with one end of vehicle raised and the opposite end on a towing dolly. 2–Wheel- Drive Vehicles Provided that the transmission is operable, tow with the transmission in Neutral and the ignition key in the OFF position along with the front wheels raised and the rear wheels on the ground.
Page 335 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment ....338 5.9L HO Cummins Turbo Diesel ... 338 Onboard Diagnostic System (OBD II) .
Page 336 336 MAINTAINING YOUR VEHICLE Front Axle Universal Drive Joints And Pivot Bearings ......358 Body Lubrication .
Page 337 Bulb Replacement ..... . 385 Headlight (Halogen)/Front Park And Turn Lights ......385 Tail, Stop, Turn And Backup Lights .
Page 338: 338 Maintaining Your Vehicle
338 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT 5.9L HO CUMMINS TURBO DIESEL...
Page 339: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC SYSTEM (OBD II) CARB emission control vehicles are equipped with a sophisticated onboard diagnostic system called OBDII. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 340: Dealer Service
340 MAINTAINING YOUR VEHICLE DEALER SERVICE Your dealer has the qualified service personnel, special tools and equipment to perform all service operations in an expert manner. Service manuals are available which include detailed service information for your vehicle. Refer to these manuals before attempting any procedure yourself.
Page 341 CAUTION! To maintain your vehicle safely follow these guide- lines: • Watch your vehicle’s mileage and check your Mainte- nance Schedules regularly for required servicing. Ex- cessive wear or damage to certain vehicle components can result if required services are not performed. •...
Page 342 • Important: All maintenance other than that listed in this manual, as well as some procedures listed here, MUST be performed by your local Dodge Truck Dealer. Your authorized Dodge Dealer has been trained and has the necessary parts to maintain your...
Page 343: Maintenance Procedures
MAINTENANCE PROCEDURES The pages that follow contain the required maintenance services determined by the engineers who designed your vehicle. Besides the maintenance items for which there are fixed maintenance intervals, there are other items that should operate satisfactorily without periodic maintenance. However, if a malfunction of these items does occur, it could adversely affect the engine or vehicle performance.
Page 344 344 MAINTAINING YOUR VEHICLE Never operate the engine with oil level below the “ADD” mark or above the upper “SAFE” mark. Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could dam- age your engine.
Page 345 NOTE: Most vehicles are operated under the conditions listed for Schedule B. Engine Oil Selection 1. Engine Oil Quality Use only oils conforming to API Ser- vice CI-4. A sulfated ash limit is speci- fied for lubrication oil used in Cum- mins engines.
Page 346 346 MAINTAINING YOUR VEHICLE Engine Oil Filter Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct part number. The engine oil filter should be changed at every engine oil change. Engine Oil And Filter — Change WARNING! Hot oil can cause personal injury. Operate the engine until the coolant temperature reaches 140°F (60°C).
Page 347 CAUTION! The filtering medium of other aftermarket filters may disintegrate. Debris from failed filters may plug the piston oil cooling nozzles, resulting in scuffed pistons and engine failure. CAUTION! Fill the oil filter element with clean oil before installation. Use the same type oil that will be used in the engine.
Page 348: Drive Belt
348 MAINTAINING YOUR VEHICLE Cummins Turbo Diesel Fill the engine with the correct grade of new oil. The engine capacity is 11 quarts (10.4 liters) in the crankcase and 1 quart (.95 liter) in the lubricating oil filter. Start the engine and operate it at idle for several minutes. Check for leaks at the lubricating oil filter and oil pan drain plug.
Page 349: Engine Air Cleaner Filter
Engine Air Cleaner Filter CAUTION! All air entering the engine intake must be filtered. The abrasive particles in unfiltered air will cause rapid wear to engine components. The air filter housing on your Diesel Ram is equipped with a Filter Minder™. This is an air flow restriction gauge that will indicate when the filter element needs to be replaced.
Page 350 350 MAINTAINING YOUR VEHICLE across the filter element increases, a yellow disc travels along a graduated scale on the side of the Filter Minder™. The yellow disc will always show the greatest restriction experienced by the filter element. When the disc reaches the red zone, the filter element may need to be replaced.
Page 351: Draining Fuel/Water Separator Filter
CAUTION! Many aftermarket performance air filter elements do not adequately filter the air entering the engine. Use of such filters can severely damage your engine. Draining Fuel/Water Separator Filter MAINTAINING YOUR VEHICLE CAUTION! Do not drain the fuel/water separator filter when the engine is running.
Page 352 352 MAINTAINING YOUR VEHICLE If more than a couple ounces of fuel has been drained, follow the directions below for “Priming if the engine has run out of fuel.” WARNING! Do not open the high pressure fuel system with the engine running.
Page 353 NOTE: A maximum blend of 5% biodiesel may be used with your Cummins Diesel equipped Dodge Ram Truck NOTE: As sufficient testing as not been completed, ethanol blends are not recommended or approved for use with your Cummins Diesel equipped Dodge Ram Truck.
Page 354: Maintenance Free Batteries
354 MAINTAINING YOUR VEHICLE Maintenance Free Batteries The top of the maintenance free batteries are perma- nently sealed. You will never have to add water, nor is periodic maintenance required. To determine the battery charge, check the battery test indicator (if equipped) on top of each battery. If the test indicator (if equipped) appears light or yellow, replace the battery.
Page 355: Air Conditioner Maintenance
WARNING! Battery posts, terminals, and related accessories con- tain lead and lead compounds. Always wash hands after handling the battery. Battery Blanket Usage A battery loses 60% of its cranking power as the battery temperature decreases to 0°F (-18°). For the same de- crease in temperature, the engine requires twice as much power to crank at the same RPM.
Page 356: Power Steering - Fluid Check
356 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. Refer to Section 3 of the Warranty Information book for further warranty information.
Page 357: Front Suspension Ball Joints
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 358: Front Prop Shaft Lubrication
358 MAINTAINING YOUR VEHICLE Front Prop Shaft Lubrication Lubricate the front driveshaft grease fitting at each oil change listed in the appropriate Maintenance Schedule for your vehicle (Schedule “A” and “B”). Use Mopar type MS-6560 (lithium based grease), or equivalent. Front Driveshaft Grease Fitting Front Axle Universal Drive Joints And Pivot Bearings...
Page 359: Windshield Wiper Blades
amount of a high quality lubricant such as Mopar Lock Cylinder Lubricant directly into the lock cylinder. Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner.
Page 360: Exhaust System
360 MAINTAINING YOUR VEHICLE After the engine has warmed, operate the defroster for a few minutes to reduce the possibility of smearing or freezing the fluid on the cold windshield. Mopar All Weather Windshield Washer Solution, used with water as directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim.
Page 361: Maintenance Schedules
of the exhaust system abnormally contacts the under- body hardware, the isolator and/or hanger should be replaced. Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Check engine coolant (antifreeze) protection every 12 months (before the onset of freezing weather, where...
Page 362 362 MAINTAINING YOUR VEHICLE operating temperature, the level of the coolant on the coolant bottle should be between the fluid level marks. Check the coolant level whenever the hood is raised. The radiator normally remains completely full, so there is no longer a need to remove the coolant pressure cap except for checking coolant freeze point or replacement with new antifreeze coolant.
Page 363 NOTE: It is the owner’s responsibility to maintain the proper level of protection against freezing according to the temperatures occurring in the area where the vehicle is operated. NOTE: Mixing coolant types will decrease the life of the engine coolant and will require more frequent coolant changes.
Page 364 364 MAINTAINING YOUR VEHICLE CAUTION! • Mixing of coolants other than specified engine coolant, may result in engine damage, and de- crease corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the speci- fied coolant as soon as possible.
Page 365: Fan
NOTE: This service procedure must be performed by a trained service technician. Make arrangements with your authorized Dodge Truck Dealer for this inspection. Charge Air Cooler (Inter-Cooler) The charge air cooler is positioned between the radiator and the air conditioner condenser.
Page 366: Hoses And Vacuum/Vapor Harnesses
366 MAINTAINING YOUR VEHICLE degrees Fahrenheit. This cooling process enables more efficient burning of fuel resulting in fewer emissions. To guarantee optimum performance of the system, keep the surfaces of the charge air cooler, condenser and radiator clean and free of debris. Periodically check the hoses leading to and from the charge air cooler for cracks or loose clamps resulting in loss of pressure and reduced engine performance.
Page 367 Brake Master Cylinder The fluid level of the master cylinder should be checked when performing under the hood service, or immedi- ately if the brake system warning lamp indicates system failure. The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a MAINTAINING YOUR VEHICLE “FULL”...
Page 368: Clutch Linkage
368 MAINTAINING YOUR VEHICLE WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire. Use only brake fluid that has been in a tightly closed container to avoid contamination from foreign matter or moisture.
Page 369: Clutch Hydraulic System
Clutch Hydraulic System The clutch hydraulic system is a sealed maintenance-free system. In the event of leakage or other malfunction, the system must be replaced. Rear Axle And 4x4 Front Driving Axle Fluid Level For Model 9.25 Front Axles and 10.5”/11.5” Rear Axles refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type.
Page 370: Transfer Case - If Equipped
370 MAINTAINING YOUR VEHICLE Transfer Case — If Equipped Fluid Level Check This fluid level can be checked by removing the filler plug. The fluid level should be to the bottom edge of the filler plug hole with the vehicle in a level position. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type.
Page 371 Procedure For Checking Fluid Level To properly check the automatic transmission fluid level, the following procedure must be used: 1. The vehicle must be on level ground. 2. The engine should be running at curb idle speed for a minimum of 60 seconds. 3.
Page 372 Authorized Dodge Dealer or Service Center. It is important that the transmission be adjusted periodically, the fluid main- tained at the correct level, and that it be drained and refilled as specified.
Page 373: Front Wheel Bearings
The use of transmission sealers should be avoided, since they may adversely affect seals. Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will “purge”...
Page 374: Noise Control System Required Maintenance & Warranty
374 MAINTAINING YOUR VEHICLE There are two groups identified: those for wheel bearings (Letter “G”) and those for chassis (Letter “L”) lubrication. Perfor- mance categories within these groups result in dual letter each group. The letter des- ignations shown in the ex- ample are the highest quality level available and when combined as shown can be used for both wheel bearing and chassis lubrication.
Page 375 Required Maintenance For Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed MAINTAINING YOUR VEHICLE or suspected.
Page 376 376 MAINTAINING YOUR VEHICLE Tampering With Noise Control System Prohibited Federal law prohibits the following acts or the causing thereof: (1) the removal or rendering inoperative by any person, other than for purposes of maintenance, repair, or replacement, of any device or element of design incorpo- rated into any new vehicle for the purpose of noise control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the vehicle...
Page 377 assembly or in any part, component or system of the vehicle as manufactured by the manufacturer, which, at the time it left the manufacturer’s control, caused noise Maintenance Log and Service Chart — 24 Valve Cummins Turbo Diesel Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed.
Page 378 378 MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log — Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES KILOMETERS Exhaust system-inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED BY PERFORMED AT 67,500 75,000 82,500...
Page 379: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 380 380 MAINTAINING YOUR VEHICLE CAUTION! Do not attempt to fold the 7 x 10 inch trailer towing mirrors forward. The 7 x 10 inch trailer towing mirrors are not designed to be folded forward and doing so will damage the mirrors and/or vehicle. •...
Page 381 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner. •...
Page 382 382 MAINTAINING YOUR VEHICLE and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery.
Page 383: Fuse And Relay Center
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 384: Vehicle Storage
384 MAINTAINING YOUR VEHICLE 2. Use specified fuses only. 3. Always properly reinstall the cover. VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: •...
Page 385: Bulb Replacement
BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Remove the expanding fastener from the headlight welt. MAINTAINING YOUR VEHICLE...
Page 386 386 MAINTAINING YOUR VEHICLE 2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame.
Page 387 MAINTAINING YOUR VEHICLE...
Page 388 388 MAINTAINING YOUR VEHICLE 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. Twist connector on turn signal/park light bulb and remove connector and bulb from housing.
Page 389: Tail, Stop, Turn And Backup Lights
Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged.
Page 390 390 MAINTAINING YOUR VEHICLE 4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights...
Page 391: Center High-Mounted Stoplight With Cargo Light
6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first. MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown.
Page 392 392 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn desired bulb socket ⁄ turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. •...
Page 393: Cab Top Clearance Lights - If Equipped
Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. MAINTAINING YOUR VEHICLE 2. Rotate the socket ⁄ turn and pull it from the light assembly.
Page 394: Tailgate Id Lights (Dual Rear Wheels)
394 MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. Tailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the rear.
Page 395 2. Turn socket ⁄ turn counterclockwise to access the bulb. MAINTAINING YOUR VEHICLE 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing.
Page 396: Side Marker Lights (Dual Rear Wheels)
396 MAINTAINING YOUR VEHICLE Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. 3. Turn socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4.
Page 397: Fluid Capacities
2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing. MAINTAINING YOUR VEHICLE FLUID CAPACITIES FLUID CAPACITIES U.S. Fuel 2500 Shortbed Models 34 gal. 2500 Longbed Models 35 gal. 3500 Shortbed Models 34 gal. 3500 Longbed Models 35 gal.
Page 398: Recommended Fluids, Lubricants And Genuine Parts
398 MAINTAINING YOUR VEHICLE RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Engine Coolant Engine Oil Engine Oil Filter Engine Fuel Filter Fuel Selection Fluids, Lubricants and Genuine Parts Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) P/N 5011764AB or equivalent. For the proper quality and SAE Grade oil for your engine, refer to the section Maintenance Procedures.
Page 399: Chassis
Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid NV 4500 Mopar 75W-85 Synthetic, API grade GL4, Mopar P/N 4874459 or equiva- Manual Transmission Fluid NV 5600 Mopar manual transmission fluid P/N 4874464 or equivalent. Manual Transmission Fluid G-56 Clutch Linkage Front and Rear Axle Fluid 2500/3500 Models Brake Master Cylinder...
Page 401 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..402 Maintenance Schedules — 24–Valve Cummins Turbo Diesel ......402 Schedule “B”...
Page 402: Emission Control System Maintenance
402 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 403 • Off-road or desert operation. • Extensive operation at high engine speeds (greater than 2900 rpm) and loads (greater than 70% throttle). NOTE: Most vehicles are operated under the conditions listed for Schedule B . NOTE: If ANY of these apply to you then change your coolant every 102,000 miles (163 000 km) or 60 months, whichever comes first and follow schedule “B”...
Page 404 404 MAINTENANCE SCHEDULES Once a Month • Check tire pressure and look for unusual wear or damage. • Inspect the batteries and clean and tighten the termi- nals as required. • Check the fluid levels of coolant reservoir, brake master cylinder, and transmission and transfer case (if equipped), add as needed.
Page 405: Schedule "B" 405
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Frequent short trips where the engine does not achieve full operating temperature (operating temperature de- fined as 190° F (66° C) coolant temperature). •...
Page 406 406 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Inspect water pump weep hole for blockage. Replace fuel filter element. Clean the water in fuel sensor.
Page 407 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Inspect drive belt, replace as required. Inspect fan hub. Inspect damper. Inspect water pump weep hole for blockage. Replace fuel filter element.
Page 408 408 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Inspect drive belt, replace as required. Inspect water pump weep hole for blockage. Replace fuel filter element.
Page 409 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only.
Page 410 410 SCHEDULE “B” Miles (Kilometers) Change front axle fluid (4X4). Change 6-spd manual transmission (G-56) fluid 2500/3500 models only. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill transfer case fluid (4X4). Drain and refill automatic transmission fluid and change main sump filter (545 RFE only).
Page 411 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Inspect drive belt, replace as required. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4).
Page 412 412 SCHEDULE “B” Miles (Kilometers) Inspect front wheel bearings. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill automatic transmission fluid. Re- place filter and adjust bands (48RE only). 78,750 82,500 86,250 (126 000) (132 000) (138 000) 90,000 93,750...
Page 413 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Flush and replace engine coolant, if not replaced at 60 months. Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Flush and replace engine coolant. Inspect drive belt, replace as required.
Page 414 414 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). Rotate tires. Flush and replace engine coolant at 120 months, if not replaced at 102,000 miles (163 000 km). Lubricate outer tie rod ends 2500/3500 (4X4) models only.
Page 415 Miles (Kilometers) Replace fuel filter element. Clean the water in fuel sensor. Inspect front wheel bearings. Change rear axle fluid. Change front axle fluid (4X4). Change 6-spd manual transmission (G-56) fluid 2500/3500 models only. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill automatic transmission fluid and change main sump and spin-on cooler return filter (if equipped) (545 RFE only).
Page 416: Schedule "A
416 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Check transfer case fluid level (4X4). Inspect water pump weep hole for blockage Replace fuel filter element.
Page 417 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Check transfer case fluid level. Flush and replace engine coolant at 60 months, if not replaced at 102,000 miles (163 000 km).
Page 418 418 SCHEDULE “A” Miles (Kilometers) [Months] Inspect fan hub. Inspect damper. Inspect front wheel bearings. Replace fuel filter element. Clean the water in fuel sensor 45,000 52,500 60,000 (72 000) (84 000) (96 000) [36] [42] [48] 67,500 75,000 (108 000) (120 000) [54] [60]...
Page 419 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Flush and replace engine coolant, if not replaced at 60 mos. Check transfer case fluid level (4X4).
Page 420 420 SCHEDULE “A” Miles (Kilometers) [Months] Inspect front wheel bearings. Inspect brake linings. Inspect and adjust parking brake if necessary. Drain and refill automatic transmission fluid. Re- place filter and adjust bands (48 RE only). 82,500 90,000 97,500 (132 000) (144 000) (156 000) [66]...
Page 421 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate Front Drive Shaft Fitting (2500/ 3500, 4X4). Rotate tires. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Flush and replace engine coolant at 120 months, if not replaced at 100,000 miles (160 000 km).
Page 422 422 SCHEDULE “A” Miles (Kilometers) [Months] Replace fuel filter element. Clean the water in fuel sensor. Inspect front wheel bearings. Inspect brake linings. Inspect and adjust parking brake if necessary. Adjust valve lash clearance. Inspection and service should also be performed anytime a malfunction is observed or suspected.
Page 423: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......424 Prepare For The Appointment .
Page 424: Suggestions For Obtaining Service For Your Vehicle
Warranty service must be done by an authorized Chrysler, Dodge, or Jeep dealer. We strongly recommend that you take your vehicle to you selling dealer. They know you and your vehicle best, and are most concerned that you get prompt and high quality service.
Page 425 This is why you should always talk to your dealer’s service manager first. Most matters can be resolved with this process. • If for some reason you are still not satisfied, talk to the general manager or owner of the dealership. They want to know if you need assistance.
Page 426: Warranty Information
426 IF YOU NEED CONSUMER ASSISTANCE Center. Any hearing or speech impaired customer who has access to a TDD or a conventional teletypewriter (TTY) in the United States can communicate with the manufacturer by dialing 1–800–380–CHRY. Service Contract You may have purchased a service contract for your vehicle to help protect you from the high cost of unex- pected repairs after your manufacturer’s new vehicle limited warranty expires.
Page 427 IF YOU NEED CONSUMER ASSISTANCE 427 U.S. Vehicles Only...
Page 428: Mopar Parts
428 IF YOU NEED CONSUMER ASSISTANCE MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra-...
Page 429: Publication Order Forms
PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form. NOTE: A street address is required when ordering manuals.
Page 430 430 IF YOU NEED CONSUMER ASSISTANCE Call Toll Free at: • 1–800–890–4038 (U.S.) • 1–800–387–1143 (Canada) Visit us on the World Wide Web at: • www.techauthority.daimlerchrysler.com • www.daimlerchrysler.ca/manuals...
Page 431 INDEX...
Page 432 432 INDEX Air Cleaner, Engine (Engine Air Cleaner Filter) . 349,375 Air Conditioner Maintenance ....355 Air Conditioning Refrigerant ... . . 355,356 Air Conditioning System .
Page 433 Body Mechanism Lubrication ....358 B-Pillar Location ......264 Brake Fluid .
Page 434 434 INDEX Child Seat ......56,62 Cigar Lighter ......144 Climate Control .
Page 435 Used Coolant ......364 Door Ajar ......164 Door Locks .
Page 436 436 INDEX Exterior Lighting ......116 Fan ........365 Filters Engine Oil .
Page 437 Glass Cleaning ......382 GVWR ....... 286 Hands-Free Phone .
Page 438 438 INDEX Jack Location ......316 Jack Operation ......318 Jump Starting .
Page 439 Low Washer Fluid ..... 168 Passing ......119 Seat Belt Reminder .
Page 440 440 INDEX Trailer Towing ..... . 81,296 Modifications/Alterations, Vehicle ... . . 8 Mopar Parts .
Page 441 Phone, Cellular ......83 Phone, Hands-Free ..... . . 83 Pickup Box .
Page 442 442 INDEX Restraint, Head ......108 Restraints, Child ..... . . 56,62 Rotation, Tires .
Page 443 Transfer Case ......246 Transfer Case, Shifting into Transfer Case Neutral (N) ....303,306 Transfer Case, Shifting out of Transfer Case Neutral (N) .
Page 444 444 INDEX Tire Safety Information ....260 Tires ....... 70,268 Air Pressure .
Page 445 Tips ....... . 297 Trailer and Tongue Weight ....294 Trailer Towing Guide .
Page 446 446 INDEX Wind Buffeting ..... . . 33,142 Window Airbag ......54 Window Fogging .
Page 447 NOTES...
Page 448 NOTES...

This manual is also suitable for:

2005 ram 2500 2005 ram 3500

Dodge 2005 DH Ram Owner's Manual

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Dodge 2005 DH Ram

Summary of Contents for Dodge 2005 DH Ram