Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....5 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: Van Conversions/Campers
HOW TO USE THIS MANUAL Consult the table of contents to determine which section contains the information you desire. The detailed index, at the rear of this manual, contains a complete listing of all subjects. WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury.
Page 6: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Key-In-Ignition Reminder ....11 Sentry Key —...
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Security Alarm System — If Equipped ..29 Rearming Of The System ....29 To Set The Alarm .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith.
Page 12: 12 Things To Know Before Starting Your Vehicle
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Security Light , located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Light will flash continuously to signal that the vehicle has been immobilized.
Page 13 Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds.
Page 14: Ignition And Steering Lock
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK Manual Transmissions When the steering wheel is in the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your vehicle. It may be difficult to turn the key from the LOCK position when starting your vehicle.
Page 15: Automatic Transmissions
Automatic Transmissions In the LOCK position, the steering and ignition systems are locked to provide antitheft protection for your ve- hicle. It may be difficult to turn the key from the LOCK position when starting your vehicle. Move the steering wheel left and right while turning the key until it turns easily.
Page 16: Door Key
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE DOOR KEY The same key used to start the vehicle is also used to unlock the doors. To unlock the vehicle doors, insert the key into the lock and turn. To lock the doors, insert the key and turn. DOOR LOCKS Manual Locks Front and Rear doors may be locked, by moving the lock...
Page 17: Power Door Locks - If Equipped
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 Power Door Locks — If Equipped NOTE: Vehicles equipped with remote keyless entry do not have a passenger side door lock cylinder. Vehicles equipped with power door locks can be locked or unlocked from inside by either the use of the door lock switches located on the front doors or by pressing the LOCK or UNLOCK buttons on the Remote Keyless Entry key fob (if equipped).
Page 18 18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking —...
Page 19 2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ).
Page 20 20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Unlock Feature Programming This feature is enabled when your vehicle is shipped from the assembly plant and can be disabled by using the following procedure: Customer Programming sequence to disable or enable: 1.
Page 21: Child Protection Door Lock
Child Protection Door Lock To provide a safer environment for children riding in the rear seat, the rear doors of your vehicle have the child- protection door lock system. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 To use the system, open each rear door and slide the control UP to engage the locks and DOWN to disengage the child-protection locks.
Page 22: Remote Keyless Entry - If Equipped
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the child protection locks are engaged. NOTE: After setting the child protection door lock system, always test the door from the inside to make certain it is in the desired position.
Page 23: To Unlock The Doors
To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds.
Page 24: To Lock The Doors
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once.
Page 25: Using The Panic Alarm
Vehicles will be shipped from the assembly plants with the park lamp flash feature activated. If desired, this feature can be disabled by using the following procedure: 1. Enter your vehicle and close all doors. 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure).
Page 26: Programming Additional Transmitters
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE automatically cancel after 3 minutes or if the vehicle is started and exceeds 15 mph. During the Panic Mode, the door locks and remote keyless entry systems will func- tion normally. Panic mode will not disarm the security system on vehicles so equipped.
Page 27: General Information
9. A single chime will be heard. The chime indicates that the fob has been recognized. 10. Within 4 seconds of hearing the chime, press and release any button on the fob being programmed. 11. A single chime will be heard. The chime indicates that the fob has been programmed.
Page 28: Transmitter Battery Service
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Closeness to a radio transmitter such as a radio station tower, airport transmitter, and some mobile or CB radios. Transmitter Battery Service The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board.
Page 29: Security Alarm System - If Equipped
SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly.
Page 30: To Disarm The System
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 31: Windows
WINDOWS Power Windows—If Equipped THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control and on the rear doors of Quad Cab models.
Page 32: Sliding Rear Window-If Equipped
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Window Lockout Switch (4 Door Models Only) The window lockout switch on the driver’s door allows you to disable the window control on the other doors.
Page 33: Wind Buffeting
WIND BUFFETING Wind buffeting can be described as the perception of pressure on the ears or a helicopter type sound in the ears. Your vehicle may exhibit wind buffeting with the windows down or partially open positions. This is a normal occurrence and can be minimized.
Page 34: Lap/Shoulder Belts
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Research has shown that seat belts save lives, and that they can reduce the seriousness of injuries in a collision. Some of the worst injuries happen when people are thrown from the vehicle. Seat belts reduce the possibility of ejection and the risk of injury caused by striking the inside of the vehicle.
Page 35 WARNING! • Wearing a seat belt incorrectly is dangerous. Seat belts are designed to go around the large bones of your body. These are the strongest parts of your body and can take the forces of a collision the best. Wearing your belt in the wrong place could make your injuries in a collision much worse.
Page 36 36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. The seat belt latch plate is above the back of the front seat, next to your arm in the rear seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
Page 37 4. Position the lap belt across your thighs, below your abdomen. To remove slack in the lap belt portion, pull up on the shoulder belt. To loosen the lap belt if it is too tight, tilt the latch plate and pull on the lap belt. A snug belt reduces the risk of sliding under the belt in a collision.
Page 38 38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 6. To release the belt, push the red button on the buckle. The belt will automatically retract to its stowed position. If necessary, slide the latch plate down the webbing to allow the belt to retract fully. WARNING! A frayed or torn belt could rip apart in a collision and leave you with no protection.
Page 39 Detaching Buckle with Key 2. To reattach the seat belt to the front center seat, pull the black buckle latch plate forward from the cab back panel and insert it into the black keyed buckle until there is an audible click. Refer to the previous section for the proper seat belt usage.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Inserting Latch Plate In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly.
Page 41: Adjustable Upper Shoulder Belt Anchorage
Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck. Press the button located on the upper belt guide, and then move it up or down to the position that serves you best.
Page 42: Center Lap Belts
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Grasp the shoulder portion and pull downward until the entire belt is extracted. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode.
Page 43: Enhanced Driver Seat Belt Reminder System (Beltalert)
NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items.
Page 44: Seat Belts And Pregnant Women
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming.
Page 45: Driver And Right Front Passenger Supplemental
WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you.
Page 47 • Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel •...
Page 49 • The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the START or RUN positions. These include all of the items listed above except the knee bolsters, the instrument panel, and the steering wheel and column.
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size.
Page 51 because the infant has a medical condition which makes it necessary for the driver to be able to see the infant, • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child,...
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Turn On the Passenger Airbag (Standard Cab Ve- hicles Only) Place the ignition key in the Passenger Airbag On/Off Switch, push the key in and turn counterclockwise, and remove the key from the switch. This will turn on the passenger airbag.
Page 53 irritation, move to fresh air. If the irritation continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s instruc- tions for cleaning. • It is not advisable to drive your vehicle after the airbags have deployed. If you are involved in another collision, the airbags will not be in place to protect you.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE bags to inflate, it signals the inflators on the crash side of the vehicle. A quantity of nontoxic gas is generated to inflate the window bag. The inflating window bag pushes the side pillar molding out of the way and covers the window.
Page 55: Child Restraint
Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: •...
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are.
Page 57 unless the airbag is turned off. An airbag deployment could cause severe injury or death to infants in this position. • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle.
Page 58 58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 59 • In the rear seat, you may have trouble tightening the lap/shoulder belt on the child restraint because the buckle or latch plate is too close to the belt path opening on the restraint. Disconnect the latch plate from the buckle and twist the short buckle-end belt several times to shorten it.
Page 60 60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE outboard positions and also feature tether strap anchor- ages, which must be used, located behind the seatback (refer to Child Restraint Tether Anchor later in this section). Identification dots are located above the standard cab front seat lower anchorages as a guide for locating lower anchors.
Page 61 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Child restraint systems having attachments designed to connect to the lower anchorages are now available. Child restraints having tether straps and hooks for connection to the seatback tether anchorage have been available for some time.
Page 62 62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Installing the Child Restraint System WARNING! Do not install child restraint systems equipped with LATCH attachments in the center position of a Quad Cab model rear seat. The LATCH anchorages in this seat are designed for the two outboard seating posi- tions only.
Page 63 WARNING! Improper installation of a child restraint to the LATCH anchorages can lead to failure of an infant or child restraint. The child could be badly injured or killed. Follow the manufacturer’s directions exactly when installing an infant or child restraint. Child Restraint Tether Anchor Child restraints having tether straps and hooks for con- nection to tether anchors have been available for some...
Page 64 64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Tether Anchorage Points at the Right and Center Front Seat (Regular Cab - All Seats) 1. Place the child restraint on the seat and adjust the tether strap so that it will reach over the seat back under the head restraint to the tether anchor directly behind the seat.
Page 65 Multiple Child Restraint Installation Sequence - (Quad Cab Rear Seats) 1. Obtain tether straps by raising the head restraints and reaching between the rear glass and rear seat. The tether strap may be retained with an elastic band. Accessibility to the tether strap is greatly improved by raising the seat cushion to the “up”...
Page 66 66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Multiple Child Restraints...
Page 67: Engine Break-In Recommendations
Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. •...
Page 68: Safety Tips
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A new engine may consume some oil during its first few thousand miles of operation. This is a normal part of the break-in and is not an indication of difficulty. CAUTION! • During the first 500 miles (805 km) your new vehicle is driven, do not tow a trailer.
Page 69: Lock Your Vehicle
Lock Your Vehicle Always remove the keys from the ignition and lock all doors when leaving the vehicle unattended, even in your own driveway or garage. Try to park your vehicle in a well-lighted area and never invite theft by leaving ar- ticles of value exposed.
Page 70: Safety Checks You Should Make Inside The Vehicle
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed.
Page 71: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......75 Inside Mirror ......75 Automatic Dimming Mirror—...
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints ....93 Manual Rotary Lumbar Support Adjustment — If Equipped ....94 Power Seats —...
Page 73 To Set At A Desired Speed ....110 To Deactivate ......110 To Resume Speed .
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Erasing Homelink Buttons ....124 Reprogramming a Single Homelink Button . . . 125 Security ......125 Electrical Power Outlets .
Page 75: Mirrors
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 75 MIRRORS Inside Mirror The mirror should be adjusted to center on the view through the rear window. Annoying headlight glare can be reduced by moving the small control under the mirror to the night position (toward rear of vehicle).
Page 76: Automatic Dimming Mirror- If Equipped
76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 77: Exterior Mirrors Folding Feature
WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object. Use your inside mirror when judging the size or distance of a vehicle seen in the right side convex mirror.
Page 78: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The controls for the power mirrors are located on the driver’s door trim panel. Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror.
Page 79: Trailer Towing Mirrors - If Equipped
Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped Out or In).
Page 80 80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE “Call” or “Dial”). Your cellular phone’s audio is trans- mitted through your vehicle’s stereo system; the system will automatically mute your radio before receiving or sending a call. UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversations.
Page 81: Operation
The UConnect™ system can be used with any Hands Free Profile certified Bluetooth™ cellular phone. If your cellular phone has a different profile (i.e. headset profile), you will not be able to use any UConnect™ features. The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system.
Page 82 82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say a four-digit pin number into the UConnect™ system which you will later need to enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number.
Page 83 • After the Ready prompt, say Dial or Call wait for the ready prompt followed by the name and designa- tion of a phonebook entry that you wish to dial. For example, you can say Call John Doe Work . Add Names to Your UConnect™...
Page 84 84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook.
Page 85: Phone Call Features
List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt, say Names . • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’...
Page 86 86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
Page 87: Advanced Phone Connectivity
Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 88 88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say All to delete all the phones.
Page 89: Uconnect™ System Features
• The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle. UConnect™ System Features Barge In - Touch Tone Phone Inputs You can use your UConnect™...
Page 90 90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. •...
Page 91: Seats
Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say Help . The UConnect™ system will play all the options at any prompt if you ask for help. Cancel At any prompt, you can say Cancel and you will be returned to the previous menu.
Page 92: 40-20-40 Front Seat
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 40-20-40 Front Seat As the name implies, the seat is divided into 3 segments. The outboard seat portions are each 40% of the total width of the seat. The back of the center portion (20%) easily folds down to provide an armrest/center storage compartment (if equipped).
Page 93: Reclining Seats
Reclining Seats The recliner handle is on the outside of the seat cushion. Pull up on the handle to release the seat back and adjust for comfort. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 93 WARNING! You can be seriously, even fatally injured riding in a seat with the seatback reclined.
Page 94: Manual Rotary Lumbar Support Adjustment - If Equipped
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To lower the head restraint, push in the button and then push down on the head restraint. Manual Rotary Lumbar Support Adjustment — If Equipped Rotating the lumbar control knob on the left side of the driver’s seatback and on the right side of the passenger’s seatback increases or decreases the lumbar support.
Page 95: Power Seats - If Equipped
Power Seats — If Equipped CAUTION! Don’t put anything under a power seat. It may cause damage to the seat controls. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Up, Down, Forward, and Rearward The power seat controls are on the outboard side of the front seat cushions.
Page 96: Heated Seats - If Equipped
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE control seat height. Change the seat angle by using the two toggle switches, tilting it up or down. Tilt Adjustment Heated Seats — If Equipped The heated seat switches are located in the instrument panel under the climate controls.
Page 97: To Open And Close The Hood
Each heated seat switch has two settings (HI and LOW). Press the switch once to obtain the desired heating position and press a second time in the same direction to turn the heated seats OFF. If you do not purposefully turn the switch OFF, the heating element in the seat will remain activated until the ignition is turned off.
Page 98 98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision.
Page 99: Lights
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 LIGHTS Interior Lights Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
Page 100: Battery Saver
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out.
Page 101: Headlamp Delay - If Equipped
Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
Page 102: Daytime Running Lights (Canada And Fleet Vehicles Only)
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Plastic is not as scratch resistant as glass and therefore different lens cleaning procedures must be followed. To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing.
Page 103: Cargo Light
CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
Page 104: Passing Light
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or...
Page 105: Windshield Wipers
Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 106: Windshield Washers
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
Page 107: Tilt Steering Column
TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 WARNING! Tilting the steering column while the vehicle is moving is dangerous.
Page 108: Driver Adjustable Pedals - If Equipped
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE DRIVER ADJUSTABLE PEDALS — IF EQUIPPED The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 109: Electronic Speed Control - If Equipped
CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path. ELECTRONIC SPEED CONTROL —...
Page 110: To Set At A Desired Speed
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed control without erasing...
Page 111: To Vary The Speed Setting
To Vary The Speed Setting When the speed control is on, speed can be increased by pressing and holding the ACCEL button. When the button is released, a new set speed will be established. Tapping the ACCEL button once will result in a speed increase (refer to the table below for the speed for your specific engine).
Page 112: To Accelerate For Passing
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Accelerate For Passing Depress the accelerator as you would normally. When the pedal is released, the vehicle will return to the set speed. NOTE: When driving uphill, at elevations above 2,000 feet (610 meters), or when the vehicle is heavily loaded (especially when towing) the vehicle may slow below the SET speed.
Page 113: Overhead Console- If Equipped
OVERHEAD CONSOLE— IF EQUIPPED The two optional overhead consoles may consist of the following features: • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) — If Equipped • Universal Garage Door Opener — If Equipped UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 114: Overhead Console With Compass/Temperature Mini-Trip Computer - If Equipped
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE OVERHEAD CONSOLE WITH COMPASS/TEMPERATURE MINI-TRIP COMPUTER — IF EQUIPPED This optional overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer (CMTC) This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 115: Reset Button
RESET Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays.
Page 116: Average Fuel Economy (Avg Eco)
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is...
Page 117: Elapsed Time (Et)
Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 WARNING! Even if the display still reads a few degrees above...
Page 118: Manual Compass Calibration
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration”...
Page 119: Outside Temperature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 120: Garage Door Opener - If Equipped
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER — IF EQUIPPED The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 121: Programming Homelink
Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. It is also recom- mended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmis- sion of the radio-frequency signal.
Page 122 122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 123: Canadian Programming/Gate Programming
If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the learn or smart button.
Page 124: Using Homelink
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the cycling process to prevent possible overheating.
Page 125: Reprogramming A Single Homelink Button
Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. DO NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with Programming step 2 For questions or comments, contact HomeLink at:...
Page 126: Electrical Power Outlets
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary electrical outlet can provide power for in cab accessories designed for use with the standard “cigar lighter” plug. The outlet is located in the instrument panel below the ash receiver. A cap is attached to the outlet base indicating “Power Outlet”...
Page 127: Cigar Lighter And Ash Receiver
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the receiver and then allowing the receiver to open. The cigar lighter is located above and to the left of the ash receiver.
Page 128: Cupholders
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Instrument Panel Cupholders — Automatic Transmission Only Your new Ram truck is equipped with dual-opening adjustable cupholders. The cupholder is opened and closed by pushing on the front surface. Each opening in the cupholder is adjustable and will hold cups and mugs of various sizes.
Page 129: Storage
STORAGE Center Storage Compartment — If Equipped The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover. Inside there is a power outlet (if equipped), removable coin holder (if equipped), and two dividers to UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 configure the storage area into compartments.
Page 130: Storage And Seats - If Equipped
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Storage and Seats — If Equipped Located in the center of the front 40/20/40 seat cushion there is a storage compartment. Standard cab models also have storage behind the seat. The Quad Cab models provide additional storage under the rear seat.
Page 131 WARNING! Do not operate the vehicle with loose items stored on the load floor. While driving or in an accident you may experience, abrupt stopping, rapid acceleration, or sharp turns. Loose objects stored on the load floor may move around with force and strike occupants, resulting in serious or fatal injury.
Page 132 132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Grasp the knob on the load floor and lift the knob until the load floor unfolds into position. 3. Reverse the procedure to store the load floor. Positioning the Load Floor for Storage Access Under the Seat 1.
Page 133: Pickup Box
4. Reverse the procedure to put the load floor back in the secured down position before you operate the vehicle. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from you dealer.
Page 134 134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor.
Page 135: Slide-In Campers
There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 136 136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: Dual rear wheel pickup models require properly spaced rear clearance lights. If such a vehicle is operated without a tailgate, suitable lights must be installed. WARNING! To avoid inhaling carbon monoxide, which is deadly, the exhaust system on vehicles equipped with “Cap or Slide-In Campers”...
Page 137: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....141 Instrument Cluster ..... . 142 Instrument Cluster Description .
Page 138 138 UNDERSTANDING YOUR INSTRUMENT PANEL Cassette Player Features ....154 CD Changer Control Capability — If Equipped ......155 Radio Display Messages .
Page 139 Pinch Roller Release ....163 Noise Reduction ..... . 163 Operating Instructions —...
Page 140 140 UNDERSTANDING YOUR INSTRUMENT PANEL Remote Sound System Controls — If Equipped . . 181 Radio Operation ..... . 182 Tape Player .
Page 141: Instruments And Controls
UNDERSTANDING YOUR INSTRUMENT PANEL 141 INSTRUMENTS AND CONTROLS...
Page 142: Instrument Cluster
142 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER...
Page 143: Instrument Cluster Description
INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 144 144 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Voltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical sys- tem should be serviced.
Page 145 7. Seat Belt Reminder Light When the ignition switch is first turned ON, this light will turn on for 5 to 8 seconds as a bulb check. During the bulb check, if the driver’s seat belt is unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously.
Page 146 146 UNDERSTANDING YOUR INSTRUMENT PANEL 12. Electronic Throttle Control (ETC) Light 5.7L Engines Only This light informs you of a problem with the Electronic Throttle Control system. If a prob- lem is detected the light will come on while the engine is running.
Page 147 CAUTION! Do not leave your vehicle unattended with the engine running as you would not be able to react to the temperature indicator if the engine overheats. 14. Security The light will flash rapidly for approximately 16 seconds when the vehicle theft alarm is arming. The light will flash at a slower rate after the alarm is set.
Page 148 148 UNDERSTANDING YOUR INSTRUMENT PANEL parking brake has not been released. This light will illuminate if the brake fluid is low, especially when braking or accelerating hard. This light will illuminate if the ABS indicator light has a malfunction. This light will flash if the engine is running and the parking brake is on.
Page 149 The trip odometer shows individual trip mileage. To toggle between the odometer and the trip odometer, press the Odometer/Trip Odometer Button. To reset the Trip Odometer, press and hold the button while in trip mode, until the Trip Odometer resets. NOTE: There is also an engine hour function.
Page 150 150 UNDERSTANDING YOUR INSTRUMENT PANEL 24. Low Wash Light This light comes on when the washer fluid level falls below approximately 1/4 filled. The light will remain on until fluid is added and one minute has elapsed. 25. Odometer/Trip Odometer Button Press this button to toggle between the odometer and the trip odometer display.
Page 151: Electronic Digital Clock
ELECTRONIC DIGITAL CLOCK The clock and radio each use the display panel built into the radio. A digital readout shows the time in hours and minutes whenever the ignition switch is in the “ON” or “ACC” position. When the ignition switch is in the “OFF” position, or when the radio frequency is being displayed, time keep- ing is accurately maintained.
Page 152: Power Button
152 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: When first learning the control functions, the user should set the controls as shown in the following list. Tone Controls…As illustrated. Speaker Control…Centered. Power Button The volume control/power button pops out when pressed, this turns the sound system ON in the mode last used.
Page 153: To Set The Push-Button Memory
To Set The Push-Button Memory When you are receiving a station that you wish to commit to push-button memory, press the SET button. The symbol SET 1 will now show in the display window. Select the “1–5” button you wish to lock onto this station and press and release that button.
Page 154: Am/Fm Selection
154 UNDERSTANDING YOUR INSTRUMENT PANEL AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received in the FM mode. Mode Button Press the MODE button to select between the cassette tape player, CD changer, or the Satellite Radio (if...
Page 155: Cd Changer Control Capability - If Equipped
Selective Music Search Press the SEEK button up or down to move the track number to skip forward or backward 1 to 7 selections. Press the SEEK button once to move 1 selection, twice to move 2 selections, etc. Fast Forward And Rewind Buttons Pressing the TUNE button up or down momentarily activates Fast Forward or Rewind and makes the direc- tional arrows appear on the display.
Page 156 156 UNDERSTANDING YOUR INSTRUMENT PANEL Mode Button To activate the CD changer, press the MODE button until CD information appears on the display. Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played.
Page 157: Radio Display Messages
UNDERSTANDING YOUR INSTRUMENT PANEL 157 An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: • Excessive vibration • Disc inserted upside down • Damaged disc • Water condensation on optics Radio Display Messages Your radio has been designed to display certain messages when a problem is detected with the CD player.
Page 158: Sales Code Raz-Am/ Fm Stereo Radio With Cassette Tape Player, Cd Player And Cd Changer Controls - If Equipped
158 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RAZ—AM/ FM STEREO RADIO WITH CASSETTE TAPE PLAYER, CD PLAYER AND CD CHANGER CONTROLS — IF EQUIPPED Operating Instructions — Radio NOTE: Power to operate the radio is controlled by the ignition switch. It must be in the ON or ACC position to operate the radio.
Page 159: Pty (Program Type) Button
PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
Page 160: Balance
160 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK”...
Page 161: Am/Fm Selection
AM/FM Selection Press the AM/FM button to change from AM to FM. The operating mode will be displayed next to the station frequency. The display will show ST when a stereo station is received. Scan Button Pressing the SCAN button causes the tuner to search for the next station, in either AM or FM, pausing for 5 seconds at each listenable station before continuing to the next.
Page 162: To Change From Clock To Radio Mode
162 UNDERSTANDING YOUR INSTRUMENT PANEL To Change From Clock To Radio Mode Press the Time button to change the display between radio frequency and time. Operating Instructions — Tape Player Insert the cassette with the exposed tape side toward the right and the mechanical action of the player will gently pull the cassette into the play position.
Page 163: Tape Eject
Tape Eject Press the EJT Tape button and the cassette will disengage and eject from the radio. Scan Button Press this button to play 10 seconds of each selection. Press the scan button a second time to cancel the feature. Changing Tape Direction If you wish to change the direction of tape travel (side being played), press the PTY button.
Page 164: Operating Instructions - Cd Player
164 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — CD Player NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. CAUTION! This CD player will accept 4 only.
Page 165: Seek Button
Seek Button Press the top of the SEEK button for the next selection on the CD. Press the bottom of the button to return to the beginning of the current selection, or return to the beginning of the previous selection if the CD is within the first 10 seconds of the current selection.
Page 166: Mode
166 UNDERSTANDING YOUR INSTRUMENT PANEL MODE Press the MODE button to select between the tape player, CD player, or satellite radio (if equipped). To select Satellite Radio (if equipped), press the MODE button until the word SIRIUS appears. The following will be displayed in this order: After three seconds, the current channel name and number will be displayed for five seconds.
Page 167 Push-Button While the CD changer is playing, press the NUMBER 1 push-button or the NUMBER 5 push-button to select a disc numbered higher or lower than the one currently being played. Seek Button Press the SEEK up or down to select another track on the same disc.
Page 168: Sales Code Rbk-Am/ Fm Stereo Radio With Cd Player And Cd Changer Controls
168 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBK—AM/ FM STEREO RADIO WITH CD PLAYER AND CD CHANGER CONTROLS Radio Operation Power/Volume Control Press the ON/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is supplied through the ignition switch.
Page 169 Balance The Balance control adjusts the left-to-right speaker bal- ance. Press the BAL button in and it will pop out. Adjust the balance and push the button back in. Fade The Fade control provides for balance between the front and rear speakers. Press the FADE button in and it will pop out.
Page 170 170 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window. Each button can be set for SET 1 and SET 2 in both AM and FM.
Page 171: Cd Player Operation
CD Player Operation NOTE: The ignition switch must be in the ON or ACC position and the volume control ON before the CD player will operate. Inserting The Compact Disc CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only.
Page 172 172 UNDERSTANDING YOUR INSTRUMENT PANEL The disc can be ejected with the radio and ignition OFF. FF/TUNE/RW Press FF (Fast Forward) and the CD player will begin to fast forward until FF is released. The RW ( Reverse) button works in a similar manner. Random Play —...
Page 173: Cd Changer Control Capability - If Equipped
CD Changer Control Capability — If Equipped This radio is compatible with a remote mounted CD changer available through Mopar Accessories. The fol- lowing instructions are for the radio controls that operate this CD changer. Mode Button To activate the CD changer, press the MODE button until CD information appears on the display.
Page 174: Radio Display Messages
174 UNDERSTANDING YOUR INSTRUMENT PANEL A CD HOT symbol indicates the player is too hot. CD HOT will pause the operation. Play can be resumed when the operating temperature is corrected or another MODE is selected. An ERR symbol will appear on the display if the laser is unable to read the Disc data for the following reasons: •...
Page 175: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. UNDERSTANDING YOUR INSTRUMENT PANEL 175 NOTE: Power to operate the radio is controlled by the ignition switch.
Page 176 176 UNDERSTANDING YOUR INSTRUMENT PANEL Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
Page 177: Cd Player Operation
5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
Page 178 178 UNDERSTANDING YOUR INSTRUMENT PANEL Inserting The Compact Disc CAUTION! This CD player will accept 4 only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 179 If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD.
Page 180 180 UNDERSTANDING YOUR INSTRUMENT PANEL PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
Page 181: Remote Sound System Controls - If Equipped
By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK” and the selected PTY program type when searching for the next PTY station.
Page 182: Radio Operation
182 UNDERSTANDING YOUR INSTRUMENT PANEL increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode. The left hand control is a rocker type switch with a push button in the center.
Page 183: Cassette Tape And Player Maintenance
If you press the switch up or down twice it plays the second track, three times, it will play the third, etc. The button in the center of the left hand switch has no function in this mode. CASSETTE TAPE AND PLAYER MAINTENANCE To keep the cassette tapes and player in good condition, take the following precautions: 1.
Page 184: Compact Disc Maintenance
184 UNDERSTANDING YOUR INSTRUMENT PANEL COMPACT DISC MAINTENANCE To keep the compact discs in good condition, take the following precautions: 1. Handle the disc by its edge; avoid touching the surface. 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge.
Page 185: Climate Controls
CLIMATE CONTROLS The controls for the heating and ventilation system in this vehicle consist of a series of rotary knobs. These comfort controls can be set to obtain desired interior conditions. UNDERSTANDING YOUR INSTRUMENT PANEL 185 Heater Only — Fleet Vehicles The mode control (at the right of the control panel) can be set in any of the following positions:...
Page 186 186 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: To improve your selection choices, the system allows you to operate at intermediate positions between the major modes. These intermediate positions are iden- tified by the small dots. Panel Outside air flows through the outlets located in the instrument panel.
Page 187: Air Conditioning-If Equipped
Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
Page 188 188 UNDERSTANDING YOUR INSTRUMENT PANEL snowflake button shows that the air conditioning is on. Press the button a second time to turn the air condition- ing off. Slight changes in engine speed or power may be noticed when the air conditioning compressor is on. This is a normal occurrence as the compressor will cycle on and off to maintain comfort and increase fuel economy.
Page 189 Floor Outside air flows primarily through the floor out- lets located under the instrument panel. Outside air flows in equal proportions through the floor and defroster outlets, and the air conditioning may be on. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield, and the demister outlets located at the edge of each side of the instrument panel, and the air...
Page 190 190 UNDERSTANDING YOUR INSTRUMENT PANEL Temperature Control The rotary knob at the center of the control panel controls the temperature of the inte- rior air. You can choose your degree of comfort by rotating the knob. The coldest tem- perature setting is to the ex- treme left (blue region) and the warmest setting is to the extreme right (red region) of...
Page 191: Electric Rear Window Defroster And Heated
Electric Rear Window Defroster and Heated Sideview Mirrors — If Equipped The Electric Rear Window Defroster and Heated side view mirrors are activated by pressing the heated grid button, located on the Climate Control panel, with the ignition On. Turning Off the ignition will deactivate the Electric Rear Window Defroster and Heated side view mirrors feature.
Page 192 192 UNDERSTANDING YOUR INSTRUMENT PANEL Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the control panel. Conditioned air will be directed through the outlets selected by the mode control. A light in the snowflake button shows that the air conditioning is on.
Page 193 Recirculation Pushbutton Pushing the Recirculation button al- lows interior air to recirculate continu- ously in any position except defrost and defrost/floor mode for rapid cool down of the interior. See “Fast Cooldown” later in this section. Mode Control The mode control allows you to choose from several patterns of air distribution.
Page 194 194 UNDERSTANDING YOUR INSTRUMENT PANEL Outside air flows in equal proportions through the floor and defroster outlets. Defrost Outside air is primarily directed to the windshield through the defroster outlets located at the base of the windshield and side window demist outlets. NOTE: The air conditioning compressor operates in both Mix and Defrost or a blend of these modes, even if the A/C button has not been pressed.
Page 195 Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 196: Operating Tips
196 UNDERSTANDING YOUR INSTRUMENT PANEL edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time.
Page 197 speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
Page 198: Operating Tips Chart
198 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Tips Chart...
Page 199 STARTING AND OPERATING CONTENTS Ignition/Starter Switch ....204 Lock ......204 Off .
Page 200 200 STARTING AND OPERATING Manually Shifted Transfer Case Operating Information/Precautions ....217 Shifting Procedure - Manually Shifted Transfer Case ......219 Transfer Case Reminder Light .
Page 201 Tire Spinning ......248 Tread Wear Indicators ....249 Replacement Tires .
Page 202 Snowplow ......280 Dodge Ram 1500 Models ....280 Before Plowing .
Page 203 Recreational Towing — 4–Wheel Drive Vehicles (Behind Motorhome, Etc.) ....284 Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped ..285 Returning To Normal Operation —...
Page 204: 204 Starting And Operating
204 STARTING AND OPERATING IGNITION/STARTER SWITCH LOCK Locks the automatic transmission shift control into the PARK position. It also engages the steering wheel lock (if equipped) when the steering wheel is turned. NOTE: This vehicle is equipped with a transmission shift interlocking system.
Page 205: Acc
Allows the electrical accessories to be used when the engine is not running. Manual Transmission Key Release Button To remove the key on vehicles equipped with manual transmissions, turn the key to the Lock position and press the button to remove the ignition key. STARTING AND OPERATING 205 Key Reminder An alarm will sound to remind you if the key is left in the...
Page 206: Automatic Transmission
206 STARTING AND OPERATING Automatic Transmission Start the engine with the selector lever in NEUTRAL or PARK position. Apply the brake before shifting to any driving range. Normal Starting of either a warm or cold engine is obtained without pumping or depressing the accelerator pedal.
Page 207: Engine Block Heater- If Equipped
If the engine shows no sign of starting after two 15 second periods of cranking with the accelerator pedal held to the floor, the normal starting procedure should be repeated. WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle.
Page 208: Transmission Shifting
208 STARTING AND OPERATING CAUTION! Long periods of engine idling, especially at high engine speeds can cause excessive exhaust tempera- tures which can damage your vehicle. Do not leave your vehicle unattended with the engine running. WARNING! Do not leave children or animals inside parked vehicles in hot weather.
Page 209 this range. Never use Park while the vehicle is in motion. Apply the parking brake when leaving the vehicle in this range. Always apply parking brake first, then place the selector in Park position. On 4-wheel-drive vehicles be sure that the transfer case is in a drive position! WARNING! Never use Park position on an automatic transmis- sion as a substitute for the parking brake.
Page 210 210 STARTING AND OPERATING “R” Reverse Use this range only after the vehicle has come to a complete stop. “N” Neutral Shift to Neutral when the vehicle is standing for pro- longed periods with the engine running. The engine may be started in this range.
Page 211 Overdrive Operation The overdrive automatic transmission contains an elec- tronically controlled fourth and fifth (if equipped) speed (Overdrive). The transmission will automatically shift from Drive to Overdrive if the following conditions are present: • the transmission selector is in Drive; •...
Page 212 212 STARTING AND OPERATING When To Use “TOW/HAUL” Mode When driving in hilly areas, towing a trailer, carrying a heavy load, etc., and frequent transmission shifting oc- curs, press the “TOW/HAUL” button. This will improve performance and reduce the potential for transmission overheating or failure due to excessive shifting.
Page 213: Manual Transmission - 5-Speed
high gear. When the vehicle speed drops or during acceleration when the transmission downshifts to second gear, the clutch automatically disengages. NOTE: The torque converter clutch will not engage until the transmission fluid and engine coolant are warm [usually after 1-3 miles (1.6 - 4.8 km) of driving]. Because the engine speed is higher when the torque converter clutch is not engaged, it may seem as if the transmission is not shifting into Overdrive when cold.
Page 214 214 STARTING AND OPERATING Manual Transmission — 5–Speed (NV3500) 1500 models are equipped with the NV3500 manual transmission. Be sure the transmission is in 1st gear when starting from a standing position. Damage to the clutch can result from starting in 2nd or 3rd gear. Use each gear in numerical order –...
Page 215 Manual Transmission Shift Speeds in MPH (KPH) Engine Model Axle Mode 1 to 2 2 to 3 3.7L 1500 3.55 ACCEL 15 (24) 25 (40) 40 (65) 45 (72) & & 3.92 CRUISE 4.7L 1500 ACCEL 15 (24) 25 (40) 40 (65) 45 (72) &...
Page 216: Four-Wheel- Drive Operation - If Equipped
For acceleration at speeds less than 20 mph (30 km/h), 2nd gear is recommended. FOUR-WHEEL- DRIVE OPERATION — IF EQUIPPED • Four-Wheel-Drive Dodge Ram Trucks are equipped with either a Manually Shifted transfer case or an Electronically Shifted transfer case. See the operating 2 to 3...
Page 217: Manually Shifted Transfer Case Operating Information/Precautions
Manually Shifted Transfer Case Operating Information/Precautions The transfer case provides 4 mode positions - 2 (rear)- wheel-drive high range, 4-wheel-drive high range, neu- tral, and 4-wheel-drive low range. This transfer case is intended to be driven in the 2-wheel- drive position (2H) for normal street and highway con- ditions such as dry hard surfaced roads.
Page 218 218 STARTING AND OPERATING place. Shifting while only the front or rear wheels are spinning can cause damage to the transfer case. Because 4-wheel drive provides improved traction, there is a tendency to exceed safe turning and stopping speeds. Do not go faster than road conditions permit. NOTE: Delayed shifts out of four-wheel drive may be experienced due to uneven tire wear, low or uneven tire pressures, excessive vehicle loading, or cold tempera-...
Page 219: Shifting Procedure - Manually Shifted Transfer Case
4-Wheel-Drive High Range - Locks the front and rear driveshafts together. Forces the front and rear wheels to rotate at the same speed. Additional traction for loose, slippery road surfaces only. Neutral - Disengages both the front and rear driveshafts from the powertrain.
Page 220: Transfer Case Reminder Light
220 STARTING AND OPERATING vehicle in motion, the transfer case will engage / disen- gage faster if you momentarily release the accelerator pedal after completing the shift. Apply a constant force when shifting the transfer case lever. 2H or 4H ⇔ 4L With the vehicle rolling at 2 to 3 mph (3 to 5 km/h), shift an automatic transmission to N (Neutral) or depress the clutch on a manual transmission.
Page 221: Electronically Shifted Transfer Case Operating Information/Precautions
Electronically Shifted Transfer Case Operating Information/Precautions This is an electric shift transfer case and is operated by the 4WD Control Switch (Transfer Case Switch), which is located on the instrument panel. The Electronically Shifted transfer case provides 4 mode positions: 2 (rear) wheel drive high range or all wheel drive high range, 4 wheel drive high range, 4 wheel drive low range, and neutral.
Page 222 222 STARTING AND OPERATING Transfer Case Position Indicator Lights — Electronically Shifted Transfer Case Only Transfer case position indicator lights are located on the Four-Wheel-Drive Control Switch, found on your instru- ment panel, and indicate the current and desired transfer case selection.
Page 223 WARNING! Always engage the parking brake when powering down the vehicle if the Service 4WD light is illuminated. Not engaging the parking brake may allow the vehicle to roll which may cause personal injury. NOTE: Do not attempt to make a shift while only the front or rear wheels are spinning.
Page 224 224 STARTING AND OPERATING WARNING! You or others could be injured if you leave the vehicle unattended with the transfer case in the Neutral (N) position without first fully engaging the parking brake. The transfer case Neutral (N) position disengages both the front and rear driveshafts from the powertrain and will allow the vehicle to move regardless of the transmission position.
Page 225: Shifting Procedure - Electronically Shifted Transfer Case
Shifting Procedure - Electronically Shifted Transfer Case STARTING AND OPERATING 225 NOTE: If any of the requirements to select a new transfer case position have not been met, the transfer case will not shift.The indicator light for the previous position will remain ON and the newly selected position indicator light will continue to flash until all the requirements for the selected position have been met.
Page 226 226 STARTING AND OPERATING return the control knob back to the original position, make certain all shift requirements have been met, wait five (5) seconds and try the shift again. NOTE: If all the requirements to select a new transfer case position have been met, the current position indica- tor light will turn OFF, the selected position indicator light will flash until the transfer case completes the shift.
Page 227 Preferred Procedure 1. With engine RUNNING, slow vehicle to 2 to 3 mph (3 to 5 km/h). 2. Shift the transmission into NEUTRAL (depress clutch on manual transmissions). 3. While still rolling, rotate the transfer case control switch to the desired position. 4.
Page 228: Limited-Slip Differential - If Equipped
228 STARTING AND OPERATING LIMITED-SLIP DIFFERENTIAL — IF EQUIPPED The limited-slip differential provides additional traction on snow, ice, mud, sand and gravel, particularly when there is a difference between the traction characteristics of the surface under the right and left rear wheels. During normal driving and cornering, the limited-slip unit per- forms similarly to a conventional differential.
Page 229: Parking Brake
PARKING BRAKE The foot operated parking brake is positioned below the lower left corner of the instrument panel. To release the parking brake, pull the parking brake release handle. NOTE: The instrument cluster red brake warning light will come on and flash to indicate that the parking brake is applied.
Page 230: Brake System
230 STARTING AND OPERATING WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury. Also be certain to leave an automatic transmission in Park, a manual transmission in Reverse or first gear.
Page 231: 3500 Dual Rear Wheel Models Only
3500 Dual Rear Wheel Models Only The brake system power assist is provided by a hydro- boost unit which shares fluid with the power steering system. You may experience some clicking or hissing noises from the hydro-boost system during hard braking conditions.
Page 232: Four-Wheel Anti-Lock Brake System - If Equipped
232 STARTING AND OPERATING WARNING! Both Anti-Lock Brake Systems contain sophisticated electronic equipment. It may be susceptible to inter- ference caused by improperly installed or high out- put radio transmitting equipment. This interference can cause possible loss of anti-lock braking capabil- ity.
Page 233 WARNING! Pumping of the anti-lock brakes will diminish their effectiveness and may lead to an accident. Pumping makes the stopping distance longer. Just press firmly on your brake pedal when you need to slow down or stop. STARTING AND OPERATING 233 WARNING! •...
Page 234: Power Steering
234 STARTING AND OPERATING POWER STEERING Your power steering system will provide mechanical steering capability if power assist is lost. If for any reason the hydraulic pressure is interrupted, it will still be possible to steer your vehicle. Under these conditions you will experience a substantial increase in steering effort.
Page 235 • European Metric tire sizing is based on European design standards. Tires designed to this standard have the tire size molded into the sidewall beginning with the section width. The letter P is absent from this tire size designation. Example: 215/65R15 96H •...
Page 236 236 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 237 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 238: Tire Identification Number (Tin)
238 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 239: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. STARTING AND OPERATING 239 Tire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle...
Page 240 240 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 241 5. Determine the combined weight of luggage and cargo being loaded on the vehicle. That weight may not safely exceed the available cargo and luggage load capacity calculated in step 4. 6. If your vehicle will be towing a trailer, load from your trailer will be transferred to your vehicle.
Page 242 242 STARTING AND OPERATING...
Page 243: Tires-General Information
WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 244: Tire Inflation Pressures
244 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 245 check tire pressure. Do not make a visual judgement when determining proper inflation. Radial tires may look properly inflated even when they are underinflated. CAUTION! After inspecting or adjusting the tire pressure al- ways reinstall the valve stem cap–if equipped. This will prevent moisture and dirt from entering the valve stem, which could damage the valve stem.
Page 246 246 STARTING AND OPERATING Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high speeds, maintaining correct tire inflation pressure is very important.
Page 247: Radial-Ply Tires
Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 248: Tire Spinning
248 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
Page 249: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 250: Alignment And Balance
250 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 251: Supplemental Tire Pressure Information
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 252 252 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of Ram 4X2 trucks. NOTE: The use of class “S” chains is permitted on 1500 Ram Trucks with P245/70R17 tires only.
Page 253: Snow Tires
SNOW TIRES Snow tires should be of the same size and type construc- tion as the front tires. Consult the manufacturer of the snow tire to determine any maximum vehicle speed requirement associated with the tire. These tires should always be operated at the vehicle maximum capacity inflation pressures under any load condition.
Page 254 254 STARTING AND OPERATING Follow the recommended tire rotation frequency for your type of driving found in the “Maintenance Schedules” Section of this manual. More frequent rotation is permis- sible if desired. The reasons for any rapid or unusual wear should be corrected prior to rotation being per- formed.
Page 255: Dual Rear Wheels
Dual Rear Wheels The tires used on dual wheel assemblies should be matched for wear to prevent overloading one tire in a set. To check if tires are even, lay a straight edge across all four tires. The straight edge should touch all the tires. STARTING AND OPERATING 255 CAUTION! 3500 Dual Rear Tires have only one approved direc-...
Page 256: Fuel Requirements
256 STARTING AND OPERATING FUEL REQUIREMENTS All engines (except 5.7L engines) are de- signed to meet all emissions regulations and provide excellent fuel economy and performance when using high quality un- leaded “regular” gasoline having an oc- All Engines tane rating of 87. The routine use of pre- Except 5.7L mium gasoline is not recommended.
Page 257: Reformulated Gasoline
and durability for your vehicle. We recommend the use of gasolines that meet the WWFC specifications if they are available. Reformulated Gasoline Many areas of the country require the use of cleaner burning gasoline referred to as “Reformulated Gasoline.” Reformulated gasolines contain oxygenates, and are spe- cifically blended to reduce vehicle emissions and im- prove air quality.
Page 258: Mmt In Gasoline
258 STARTING AND OPERATING MMT In Gasoline MMT is a manganese-containing metallic additive that is blended into some gasoline to increase octane. Gasolines blended with MMT provide no performance advantage beyond gasolines of the same octane number without MMT. Gasolines blended with MMT reduce spark plug life and reduce emission system performance.
Page 259: Materials Added To Fuel
CAUTION! If the Check Engine or Service Engine Soon light is flashing, immediate service is required; see onboard diagnostics system section. Materials Added To Fuel All gasolines sold in the United States are required to contain effective detergent additives. Use of additional detergents or other additives is not needed under normal conditions and would result in unnecessary cost.
Page 260 260 STARTING AND OPERATING Fuel Filler Cap (Gas Cap) The gas cap is behind the fuel filler door. If the gas cap is lost or damaged, be sure the replacement cap is for use with this vehicle. CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap).
Page 261: Fuel System Cautions
Fuel System Cautions CAUTION! Follow these guidelines to maintain your vehicle’s performance: • The use of leaded gas is prohibited by Federal law. Using leaded gasoline can impair engine performance, damage the emission control system, and could result in loss of warranty coverage. •...
Page 262: Carbon Monoxide Warnings
262 STARTING AND OPERATING Carbon Monoxide Warnings WARNING! Carbon monoxide (CO) in exhaust gases is deadly. Follow the precautions below to prevent carbon monoxide poisoning: • Do not inhale exhaust gases. They contain carbon monoxide, a colorless and odorless gas which can kill. Never run the engine in a closed area, such as a garage, and never sit in a parked vehicle with the engine running for an extended period.
Page 263: Ethanol Fuel (E-85)
CAUTION! Only vehicles with the E-85 fuel filler door label can operate on E-85. ETHANOL FUEL (E-85) E-85 is a mixture of approximately 85% fuel ethanol and 15% unleaded gasoline. WARNING! Ethanol vapors are extremely flammable and could cause serious personal injury. Never have any smok- ing materials lit in or near the vehicle when remov- ing the fuel filler tube cap (gas cap) or filling the tank.
Page 264: Selection Of Engine Oil
264 STARTING AND OPERATING NOTE: When the ambient temperature is above 90°F, you may experience hard starting and rough idle follow- ing start up even if the above recommendations are followed. Selection Of Engine Oil For best performance and protection of your vehicle, use only crankcase engine oils that meet the following re- quirements: •...
Page 265: Starting
Starting The characteristics of E-85 fuel make it unsuitable for use when ambient temperatures fall below 0°F. In the range of 0°F to 32°F, you may experience an increase in the time it takes for your engine to start, and a deterioration in drivability (sags and/or hesitations) until the engine is fully warmed up.
Page 266: Catalytic Converter
266 STARTING AND OPERATING CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, you must keep the en- gine maintained to assure proper operation and prevent possible damage.
Page 267: Vehicle Loading
vehicle should be stopped, the engine shut off and the vehicle allowed to cool. Service, including a tune-up to manufacturer’s specifications should be obtained imme- diately. To minimize the possibility of catalyst damage: • Do not try to start the engine by pushing or towing the vehicle.
Page 268 268 STARTING AND OPERATING rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.
Page 269 Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer- cial scale to insure that the GVWR has not been exceeded.
Page 270: Trailer Towing
Gross Vehicle Weight Rating (GVWR) 6500 LBS. TRAILER TOWING All Dodge Ram Pickup trucks are intended to tow trailers up to 2,000 lbs (907 kg) without added equipment or alterations to standard equipment. Your vehicle may be...
Page 271 include a 150 lb (68 kg) allowance for the presence of a driver.) Tongue Weight (of a trailer) is the weight placed on a vehicle’s trailer hitch by the trailer. GROSS TRAILER WEIGHT (GTW) is the weight of the trailer plus the weight of all cargo, consumables and equipment (permanent or temporary) loaded in or on the trailer in its loaded and ready for operation condition.
Page 272: Axle Lubricant And Trailer Towing
272 STARTING AND OPERATING NOTE: Remember that everything put into or on the trailer adds to the load on your vehicle. Also, additional factory-installed options, or dealer-installed options, must be considered as part of the total load on your vehicle. Refer to the Certification label located at the driver’s door for the Gross Vehicle Weight Rating.
Page 273: Trailer Towing Recommendations
2500/3500 Models • The Axles on 2500/3500 Models are trailer tow ready and DO NOT REQUIRE any special axle lubes or additives. Trailer Towing Recommendations • All trailer hitches should be professionally installed on your vehicle. • Safety chains must always be used between your vehicle and trailer.
Page 274: Trailer Towing - Hitches
274 STARTING AND OPERATING • Be sure the trailer is loaded heavier in front, with 60% to 65% of the weight in front of the axle(s). Loads balanced over the wheels or heavier in the rear can cause the trailer to sway severely side to side which will cause loss of control of vehicle and trailer.
Page 275: Connecting Trailer Lighting And Electric Trailer Brakes
Connecting Trailer Lighting And Electric Trailer Brakes NOTE: A 4-way trailer tow connector, located behind the bumper, is standard equipment on all Ram pickup models. This connector contains the following vehicle circuits: park/tail lamps, left stop/turn lamp, right stop/ turn lamp, and ground. With the optional Trailer Tow Prep package a 7-way connector is also provided with the following additional circuits: backup lamp, trailer battery and electric brake.
Page 276: Trailer Weight And Trailer Tongue Weight
276 STARTING AND OPERATING CAUTION! Connect trailer lighting and brakes using factory harnesses only. Do not cut or splice wiring to the brake circuits. Use an approved wiring harness con- nector on the trailer. Trailer Weight and Trailer Tongue Weight Gross Trailer Weight (GTW) means the weight of the trailer plus the weight of all cargo, consumables and equipment loaded on the trailer when in actual under-...
Page 277: Trailer Towing Information (Maximum Trailer Weight Ratings)
4. GAWR ratings Trailer Towing Information (Maximum Trailer Weight Ratings) Trailer Towing Guide NOTE: For trailer towing information (maximum trailer weight ratings) refer to the following website address: http:// www.dodge.com/towing. In Canada, refer to the following website address: http:// www.dodge.ca.
Page 278: Trailer Towing Mirrors - If Equipped
278 STARTING AND OPERATING Trailer Towing Mirrors — If Equipped These mirrors are designed with an adjustable mirror head to provide a greater vision range when towing extra-wide loads. To change position inboard or out- board, the mirror head should be rotated (flipped Out or In).
Page 279: Automatic Transmission Oil Temperature Warning Light
• Air Conditioning— turn it off temporarily. • Hilly Terrain— Turn overdrive off. See Cooling System Operating information in the Service and Maintenance section of this manual for more infor- mation. Automatic Transmission Oil Temperature Warning Light All vehicles with automatic transmissions are equipped with a transmission sump oil temperature sensor and warning light.
Page 280: Snowplow
Snowplow Prep Packages are available as a factory installed option. These packages include components necessary to equip your vehicle with a snowplow. Dodge Ram 1500 Models NOTE: Do not use Dodge Ram 1500 Models for snow- plow applications. WARNING! On 1500 Models, snowplows, winches, and other aftermarket equipment should not be added to the front end of your vehicle.
Page 281: Before Plowing
• Check that snowplow lighting is connected and func- tioning properly. Snowplow Model Prep Package Availability For Detailed Information Visit www.dodge.com or refer to the 2004 Dodge Truck Body Builders Guide. 1. The 1500 models are NOT available for snowplow applications.
Page 282: Over The Road Operation With Snowplow Attached
282 STARTING AND OPERATING 2. The maximum number of occupants in the truck should not exceed two. 3. The total GVWR or the Front GAWR or the Rear GAWR should never be exceeded. 4. The snowplow prep packages are not available with the Sport Package.
Page 283: Methods For Removing Snow
conditions permit. Do not exceed 40 mph (64 km/h). The operator should always maintain a safe stopping distance and allow adequate passing clearance. Methods For Removing Snow STARTING AND OPERATING 283 Operating Tips Under ideal snow plowing conditions, 20 mph (32 km/h) should be maximum operating speed.
Page 284: General Maintenance
284 STARTING AND OPERATING General Maintenance Snowplows should be maintained in accordance with the plow manufacturer’s instructions. Whenever the plow is disconnected from the vehicle, coat the exposed angling cylinder rods with chassis lubricant. The lift cylinder should be extended upward and chassis lubricant ap- plied to the lift rod.
Page 285: Recreational Towing Procedure - Manual Shift Transfer Case - If Equipped
for recreational towing. Refer below for the proper trans- fer case Neutral shifting procedure for your vehicle. Recreational Towing Procedure — Manual Shift Transfer Case — If Equipped Use the following procedure to prepare your vehicle for recreational towing: CAUTION! It is necessary to follow these steps to be certain that the transfer case is fully in N (NEUTRAL) before recreational towing to prevent damage to internal...
Page 286: Returning To Normal Operation - Manual Shift Transfer Case
286 STARTING AND OPERATING CAUTION! Damage to the automatic transmission may occur if the transmission is shifted into P (PARK) with the transfer case in N (NEUTRAL) and the engine RUN- NING. With the transfer case in N (NEUTRAL) ensure that the engine is OFF prior to shifting the transmission into P (PARK) Returning to Normal Operation —...
Page 287: Recreational Towing Procedure - Electronic Shift Transfer Case - If Equipped
CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and damage the internal parts. Recreational Towing Procedure —...
Page 288 288 STARTING AND OPERATING 7. After shift is completed and the Neutral (N) light comes on release Neutral (N) button. 8. Start engine. 9. Shift automatic transmission into Reverse (R). 10. Release brake pedal for five seconds and ensure that there is no vehicle movement.
Page 289: Returning To Normal Operation - Electronic Shift Transfer Case
CAUTION! Damage to the transmission may occur if the trans- mission is shifted into Park (P) with the transfer case in Neutral (N) and the engine RUNNING. With the transfer case in Neutral (N) ensure that the engine is OFF prior to shifting the transmission into Park (P). Returning to Normal Operation —...
Page 290 290 STARTING AND OPERATING during the 1 second time, then all of the mode position indicator lights will flash continuously until all require- ments are met or until the Neutral (N) button is released. NOTE: The ignition key must be ON for a shift to take place and for the position indicator lights to be operable.
Page 291: Driving Off-Road
CAUTION! • Do not use a bumper mounted clamp-on tow bar on your vehicle. The bumper face bar will be damaged. • Do not disconnect the rear driveshaft because fluid will leak from the transfer case and fluid loss will damage internal parts. DRIVING OFF-ROAD Care should be taken when attempting to climb steep hills or driving diagonally across a hill or slope.
Page 292: Traction
292 STARTING AND OPERATING If you experience unusual vibration after driving in mud, slush or similar conditions, check the wheels for im- pacted material. Impacted foreign material can cause a wheel imbalance. Removing the foreign material from the wheels will correct the situation. TRACTION When driving on wet or slushy roads, it is possible for a wedge of water to build up between the tire and road...
Page 293 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Lights ....294 Adding Fuel ......295 Jack Location .
Page 294: 294 What To Do In Emergencies
294 WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency.
Page 295: Adding Fuel
ADDING FUEL The fuel tank filler tube has a restricting door about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to force open the restricting door. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
Page 296: Jack Location
296 WHAT TO DO IN EMERGENCIES JACK LOCATION Removal (All Models) The jack and jack tools are stored under the front passenger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
Page 297 2500/3500 Model Vehicles WHAT TO DO IN EMERGENCIES 297 WARNING! The jack is designed to use as a tool for changing tires only. The jack should not be used to lift the vehicle for service purposes, unless suitable sup- ports are placed under the vehicle as a safety mea- sure.
Page 298: Reinstalling The Scissors-Type Jack And Tools (1500 Models)
298 WHAT TO DO IN EMERGENCIES Reinstalling The Scissors-Type Jack And Tools (1500 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw.
Page 299 WHAT TO DO IN EMERGENCIES 299 3. Fold the flap and roll the jack tool kit into a cylindrical package (in direction of arrows), and tie to the jack using the tie straps. Tying Bag to Jack with Straps Folding Flap and Rolling Bag...
Page 300 300 WHAT TO DO IN EMERGENCIES Jack and Tools Tied Together 1500 Model Vehicles 4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
Page 301: Changing A Flat Tire
CHANGING A FLAT TIRE Removing The Spare Tire Remove the spare tire before attempting to jack the truck. Attach the wheel wrench to the jack extension tube. Insert the tube through the access hole between the lower tailgate and the top of the bumper and into the winch mechanism tube.
Page 302: Tire Changing Procedure
302 WHAT TO DO IN EMERGENCIES Tire Changing Procedure WARNING! Getting under a jacked-up vehicle is dangerous. The vehicle could slip off the jack and fall on you. You could be crushed. Never get any part of your body under a vehicle that is on a jack. Never start or run the engine while the vehicle is on a jack.
Page 303 • Turn on the Hazard Warning Flasher. • Block both the front and rear of the wheel diagonally oppo- site the jacking position. For example, if the right front wheel is being changed, block the left rear wheel. • Passengers should not remain in the vehicle when the vehicle is being jacked.
Page 304 304 WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3.
Page 305 1500 4X4 Jacking Location • For 2500/3500 4x2 series trucks, when changing a front wheel, place the bottle jack under the frame rail behind the wheel. Locate the jack as far forward as possible on the straight part of the frame. WHAT TO DO IN EMERGENCIES 305 2500/3500 4X2 Jacking Location •...
Page 306 306 WHAT TO DO IN EMERGENCIES Place the jack under the axle as close to the tire as possible with the drive tubes extending to the front. Connect the jack tube extension and wheel wrench. 2500/3500 4X4 Jacking Location • For all trucks, when changing a rear wheel, as- semble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 307 NOTE: If the 2500/3500 bottle jack will not lower by turning the dial (thumb wheel) by hand, it may be necessary to use the jack drive tube in order to lower the jack. 4. By rotating the wheel wrench clockwise, raise the vehicle until the wheel just clears the surface.
Page 308 308 WHAT TO DO IN EMERGENCIES WARNING! A loose tire or jack thrown forward in a collision or hard stop could injure someone in the vehicle. Always stow the jack parts and the extra tire and wheel in the places provided. 7.
Page 309 back and forth motion, loosen the wheel skin. Repeat this procedure around the tire until the skin pops off. Replace the wheel skins first using a rubber mallet. When replacing the hub caps, tilt the cap retainer over the lugnut bolt circle and strike the high side down with a rubber mallet.
Page 310 310 WHAT TO DO IN EMERGENCIES Dual wheel models require a special heavy-duty lug nut tightening adapter (included with the vehicle) to cor- rectly tighten the lug nuts. Also, when it is necessary to remove and install dual rear wheels, use a proper vehicle lifting device.
Page 311 1. Tighten the wheel nuts in the numbered sequence to a snug fit. 2. Retighten the wheel nuts in the same sequence to the torques listed in the table. Go through the sequence a second time to verify that specific torque has been achieved.
Page 312: Hoisting
312 WHAT TO DO IN EMERGENCIES Attach the wheel wrench to the extension tube. Rotate the winch mechanism until the wheel is drawn into place against the underside of the vehicle. Continue to rotate until you feel the winch mechanism slip or click 3 or 4 times.
Page 313 WARNING! Battery fluid is a corrosive acid solution; do not allow battery fluid to contact eyes, skin or clothing. Don’t lean over battery when attaching clamps or allow the clamps to touch each other. If acid splashes in eyes or on skin, flush contaminated area immedi- ately with large quantities of water.
Page 314 314 WHAT TO DO IN EMERGENCIES both vehicles, place the automatic transmission in Park or the manual transmission in Neutral, and turn the ignition OFF. 3. Turn off the heater, radio, and all unnecessary electri- cal loads. 4. Connect one end of a jumper cable to the positive terminal of the booster battery.
Page 315 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! • Do not connect the cable to the negative post of the discharge battery.
Page 316: Freeing A Stuck Vehicle
316 WHAT TO DO IN EMERGENCIES FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can often be moved by a rocking motion. Move the gear selector rhythmically between DRIVE and REVERSE, while applying slight pressure to the accelerator. In general, the least amount of accelerator pedal pressure to maintain the rocking motion without spinning the wheels or racing the engine is most effective.
Page 317: Towing A Disabled Vehicle
CAUTION! Tow hooks are for emergency use only, to rescue a vehicle stranded off road. Do not use tow hooks for tow truck hookup or highway towing. You could damage your vehicle. TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle.
Page 318 318 WHAT TO DO IN EMERGENCIES If the vehicle is to be towed more than 15 miles (25 km) the vehicle must be towed with the rear wheels raised and the front wheels on the ground. It may also be towed on a flatbed or with the front wheels raised and the rear wheels on a dolly.
Page 319 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment— 3.7L/4.7L ... 322 Engine Compartment— 5.7L ....323 Onboard Diagnostic System (OBD II) ..324 Emissions Inspection And Maintenance Programs .
Page 320 320 MAINTAINING YOUR VEHICLE Maintenance Free Battery ....337 Air Conditioner Maintenance ... . . 338 Power Steering —...
Page 321 Appearance Care And Protection From Corrosion ......361 Fuse And Relay Center ....365 Vehicle Storage .
Page 322: 322 Maintaining Your Vehicle
322 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 3.7L/4.7L...
Page 323: Engine Compartment- 5.7L
MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 5.7L...
Page 324: Onboard Diagnostic System (Obd Ii)
324 MAINTAINING YOUR VEHICLE ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emis- sions well within current government regulations.
Page 325 For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
Page 326: Dealer Service
326 MAINTAINING YOUR VEHICLE b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility.
Page 327: Replacement Parts
WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 328 328 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. •...
Page 329: Engine Oil
MAINTAINING YOUR VEHICLE Engine Oil Checking Oil Level To assure proper lubrication of your vehicle’s engine, the engine oil must be maintained at the correct level. The best time to check the engine oil level is about 5 minutes after a fully warmed up engine is shut off or before starting the engine after it has sat overnight.
Page 330: Maintenance Schedules
330 MAINTAINING YOUR VEHICLE Change Engine Oil CAUTION! Overfilling or underfilling the crankcase will cause oil aeration or loss of oil pressure. This could dam- age your engine. Road conditions as well as your kind of driving affect the interval at which your oil should be changed. Check the following to determine if any apply to you: •...
Page 331 Dusty Conditions Driving through dust-laden air increases the problems of keeping abrasive materials out of the engine. Under these conditions, special attention should be given to the engine air cleaner, the crankcase inlet air cleaner and the crankcase ventilation system. Make sure that these units are clean at all times.
Page 332 332 MAINTAINING YOUR VEHICLE • SAE 5W-30 is the preferred oil for Dodge Trucks with 3.7L/4.7L/5.7L engines. • Lubricants which do not have both the engine oil certification mark or current service symbol and the correct viscosity grade number should not be used.
Page 333: Engine Oil Filter
governmental agency for advice on how and where used oil and oil filters can be safely discarded in your area. Engine Oil Filter The engine oil filter should be replaced at every engine oil change. Engine Oil Filter Selection The manufacturer’s engines have a full-flow type oil filter.
Page 334: Engine Air Cleaner Filter
334 MAINTAINING YOUR VEHICLE Engine Air Cleaner Filter Under normal driving conditions, replace the air filter at the intervals shown on Schedule “A”. If, however, you drive the vehicle frequently under dusty or severe con- ditions, the filter element should be inspected periodi- cally and replaced if necessary at the intervals shown on Schedule “B”.
Page 335: Catalytic Converter
Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Page 336: Emission-Related Components
336 MAINTAINING YOUR VEHICLE WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Page 337: Maintenance Free Battery
MAINTAINING YOUR VEHICLE plugged or sticking, replace with a new valve— do not attempt to clean the old PCV valve! Check the ventila- tion hoses for indications of damage, weepage or plug- ging with deposits. Replace if necessary. Maintenance Free Battery The top of the maintenance free battery is permanently sealed.
Page 338: Air Conditioner Maintenance
338 MAINTAINING YOUR VEHICLE WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 339: Power Steering - Fluid Check
WARNING! • Use only refrigerants and compressor lubricants approved by the manufacturer for your air condi- tioning system. Some unapproved refrigerants are flammable and can explode, injuring you. Other unapproved refrigerants or lubricants can cause the system to fail, requiring costly repairs. •...
Page 340: Front Suspension Ball Joints
340 MAINTAINING YOUR VEHICLE apparent, and/or the system is not functioning as antici- pated. Coordinate inspection efforts through a certified DaimlerChrysler Dealership. WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading.
Page 341: Steering Linkage - Inspection
Steering Linkage — Inspection Whenever the vehicle is hoisted, all steering linkage joints should be inspected for evidence of damage. If seals are damaged, parts should be replaced to prevent leakage or contamination of the grease. Lubricate the steering linkage regularly according to the “Maintenance Schedule”...
Page 342: Windshield Wiper Blades
342 MAINTAINING YOUR VEHICLE Windshield Wiper Blades The rubber edges of the wiper blades and the windshield should be cleaned periodically with a sponge or soft cloth and a mild nonabrasive cleaner. This will remove accu- mulations of salt or road film. Operation of the wipers on dry glass for long periods may cause deterioration of the wiper blades.
Page 343: Exhaust System
directed on the container, aids cleaning action, reduces the freezing point to avoid line clogging, and is not harmful to paint or trim. Exhaust System The best protection against carbon monoxide entry into the vehicle body is a properly maintained engine exhaust system.
Page 344: Cooling System
344 MAINTAINING YOUR VEHICLE Cooling System Cooling System Maintenance At the intervals shown in the Maintenance Schedules Section of the manual, the system should be drained, flushed and filled. Inspection Coolant protection checks should be made every 12 months (prior to the onset of freezing weather, where applicable).
Page 345 The radiator normally remains completely full, so there is no longer a need to remove the coolant pressure cap except for checking coolant freeze point or replacement with new antifreeze coolant. WARNING! Never add coolant to the radiator when the engine is overheated.
Page 346 346 MAINTAINING YOUR VEHICLE When additional coolant is needed to maintain the proper level, add the recommended concentration of antifreeze and water to the coolant bottle. Do not overfill. NOTE: Failure to follow the antifreeze concentration and replacement recommendations, or failure to use antifreeze formulated to prevent corrosion of all cooling system metals, may result in radiator plugging, overheat- ing, or cooling system leaks such as in core hole plugs.
Page 347: Hoses And Vacuum/Vapor Harnesses
Disposal Of Used Engine Coolant Used ethylene glycol based engine coolant is a regulated substance requiring proper disposal. Check with your local authorities to determine the disposal rules for your community. Do not store ethylene glycol-based engine coolant in open containers or allow it to remain in puddles on the ground.
Page 348: Brake System
348 MAINTAINING YOUR VEHICLE Insure nylon tubing in these areas has not melted or collapsed. Inspect all hose connections such as clamps and cou- plings to make sure they are secure and no leaks are present. Components should be replaced immediately if there is any evidence of wear or damage that could cause failure.
Page 349: Clutch Hydraulic System
WARNING! Use of a brake fluid that may have a lower initial boiling point, or is unidentified as to specification, may result in sudden brake failure during hard prolonged braking. You could have an accident. WARNING! Overfilling the brake fluid reservoir can result in spilling brake fluid on hot engine parts and the brake fluid catching fire.
Page 350: Clutch Linkage
350 MAINTAINING YOUR VEHICLE Clutch Linkage If the clutch pedal linkage begins to squeak or grunt, the clutch pedal pivot bushings should be lubricated. Refer to Recommended Fluids, Lubricants and Genuine Parts for the correct lubricant type. Propeller Shaft Universal Joints Cross Type (No fittings) —...
Page 351: Transfer Case
NOTE: The presence of water in the gear lubricant will result in corrosion and possible failure of differential components. Operation of the vehicle in water, as may be encountered in some off-highway types of service, will require draining and refilling the axle to avoid damage. Limited-Slip Differentials in 1500 Model vehicles re- quire that 4 oz.
Page 352: Automatic Transmission
352 MAINTAINING YOUR VEHICLE Lubricant Selection NV-3500 (5-Speed Manual Transmission — If Equipped) This transmission is filled with manual transmission fluid at the factory. This fluid does not require periodic changing. If it is necessary to add or change fluid in this transmission refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 353 To check the automatic transmission fluid level properly, the following procedure must be used: 1. Operate the engine at idle speed and normal operating temperature. 2. The vehicle must be on level ground. 3. Fully apply the parking brake and press the brake pedal.
Page 354 354 MAINTAINING YOUR VEHICLE CAUTION! Be aware that if the fluid temperature is below 50°F (10°C) it may not register on the dipstick. Do not add fluid until the temperature is elevated enough to produce an accurate reading. 7. Check for leaks. Release parking brake. To prevent dirt and water from entering the transmission after checking or replenishing fluid, make certain that the dipstick cap is properly reseated.
Page 355: Front Wheel Bearings
The use of transmission sealers should be avoided, since they may adversely affect seals. Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will “purge”...
Page 356: Selection Of Lubricating Grease
356 MAINTAINING YOUR VEHICLE Selection of Lubricating Grease The National Lubricating Grease Institute (NLGI) has developed a symbol (Certification Mark) to aid the vehicle owner in the proper selection of grease for the lubrication of wheel bearings and chassis components. This symbol (an example is shown below) is located on the grease container and identifies the application and quality of the grease.
Page 357 Required Maintenance for Noise Control Systems The following maintenance services must be performed every 6 months or 6,000 miles (9 600 km), whichever comes first, to assure proper operation of the noise control systems. In addition, inspection and service should be performed anytime a malfunction is observed MAINTAINING YOUR VEHICLE or suspected.
Page 358 358 MAINTAINING YOUR VEHICLE control prior to its sale or delivery to the ultimate purchaser or while it is in use, or (2) the use of the vehicle after such device or element of design has been removed or rendered inoperative by any person. Among those acts presumed to constitute tampering are the acts listed below.
Page 359 Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 6,000 12,000 KILOMETERS 9 600 19 000 Exhaust system- inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED PERFORMED 18,000 24,000...
Page 360 360 MAINTAINING YOUR VEHICLE Noise Systems Maintenance Chart and Service Log Insert Month, Day, Year under column mileage closest to the mileage at which service was performed. MILES 54,000 KILOMETERS 87 000 Exhaust system- inspect Air cleaner assembly-inspect ODOMETER READING PERFORMED PERFORMED 60,000...
Page 361: Appearance Care And Protection From Corrosion
Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage. Chemicals that make roads passable in snow and ice, and those that are sprayed on trees and road surfaces during other seasons, are highly corrosive to the metal in your vehicle.
Page 362 362 MAINTAINING YOUR VEHICLE • Avoid using abrasive compounds and power buffing that may diminish the gloss or thin out the paint finish. CAUTION! Do not use abrasive or strong cleaning materials such as steel wool or scouring powder, which will scratch metal and painted surfaces.
Page 363 • If you carry special cargo such as chemicals, fertilizers, de-icer salt, etc., be sure that such materials are well packaged and sealed. • If a lot of driving is done on gravel roads, consider mud or stone shields behind each wheel. •...
Page 364 364 MAINTAINING YOUR VEHICLE Glass Surfaces All glass surfaces should be cleaned on a regular basis with any commercial household-type glass cleaner. Never use an abrasive type cleaner. Use caution when cleaning inside rear windows equipped with electric defrosters or windshields equipped with a windshield wiper de-icer.
Page 365: Fuse And Relay Center
FUSE AND RELAY CENTER Your vehicle is equipped with a fuse and relay center located in the engine compartment near the battery. Located on the underside of the cover is a label that identifies each component. 1. Disconnect the battery negative (-) cable before remov- ing the cover.
Page 366: Replacement Light Bulbs
366 MAINTAINING YOUR VEHICLE REPLACEMENT LIGHT BULBS LIGHT BULBS — Inside Overhead Console Lights ....TS 212-2 Dome Light......7679 All of the inside bulbs are brass or glass wedge base.
Page 367 MAINTAINING YOUR VEHICLE...
Page 368 368 MAINTAINING YOUR VEHICLE 2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame.
Page 369 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. MAINTAINING YOUR VEHICLE 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. Twist connector on turn signal/park light bulb and remove connector and bulb from housing.
Page 370: Tail, Stop, Turn And Backup Lights
370 MAINTAINING YOUR VEHICLE 7. Twist collar on headlight halogen bulb remove headlight bulb from the housing. 8. Replace headlight or turn signal bulb. Do not touch the headlight halogen bulb. 9. Reverse procedure for installation of bulbs and hous- ing.
Page 371 3. Push the red lock slide in on the connector and remove the housing from the vehicle. MAINTAINING YOUR VEHICLE 4. Remove the four (4) screws from the bulb strip in the housing.
Page 372: Center High-Mounted Stoplight With Cargo Light
372 MAINTAINING YOUR VEHICLE 5. Pull the appropriate bulb straight from the bulb strip. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights 6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first.
Page 373 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn desired bulb socket ⁄ turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. MAINTAINING YOUR VEHICLE • Outside Bulbs: Cargo Lamps •...
Page 374: Cab Top Clearance Lights - If Equipped
374 MAINTAINING YOUR VEHICLE Cab Top Clearance Lights — If Equipped 1. Remove the two screws from the top of the light. 2. Rotate the socket ⁄ turn and pull it from the light assembly.
Page 375: Tailgate Id Lights (Dual Rear Wheels)
MAINTAINING YOUR VEHICLE 3. Pull the bulb straight from it’s socket and replace. Tailgate ID Lights (Dual Rear Wheels) 1. Remove the two screws and housing and access the bulb sockets from the rear.
Page 376 376 MAINTAINING YOUR VEHICLE 2. Turn socket ⁄ turn counterclockwise to access the bulb. 3. Pull bulb straight out from socket. 4. Reverse procedure for installation of bulbs and hous- ing.
Page 377: Side Marker Lights (Dual Rear Wheels)
Side Marker Lights (Dual Rear Wheels) 1. Push rearward on the side marker light assembly. 2. Pull the entire assembly from the fender. MAINTAINING YOUR VEHICLE 3. Turn socket ⁄ turn counterclockwise and remove from assembly to access the bulb. 4.
Page 378: Fog Lights
378 MAINTAINING YOUR VEHICLE Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise ⁄ turn and remove connector and bulb from housing. 2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing.
Page 379: Fluids And Capacities
FLUIDS AND CAPACITIES Fuel 3.7L/4.7L, 87 Octane 5.7L, 89 Octane 1500 Shortbed Models 1500 Longbed Models 2500 Shortbed Models 2500 Longbed Models 3500 Shortbed Models 3500 Longbed Models Engine Oil (with filter) 3.7L Engine V-6, SAE 5W-30, API Certified 4.7L Engine V-8, SAE 5W-30, API Certified 5.7L Engine V-8, SAE 5W-30, API Certified MAINTAINING YOUR VEHICLE U.S.
Page 380 380 MAINTAINING YOUR VEHICLE Cooling System 3.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 4.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) 5.7L (Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula) U.S. Metric 17 qts. 17 qts. 18.7 qts. 17.7L...
Page 381: Recommended Fluids, Lubricants And Genuine Parts
RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) P/N 5011764AB or equivalent. Engine Oil Use SAE 5W-30, API Certified, meeting material standard MS-6395. Refer to oil viscosity chart for alternative grade.
Page 382: Chassis
382 MAINTAINING YOUR VEHICLE Chassis Component Automatic Transmission Transfer Case Manual Transmission Fluid NV 3500 Mopar “Manual Transmission Fluid” P/N 4874464. Manual Transmission Fluid NV 4500 75W-85 Synthetic, API grade GL4, Mopar P/N 4874459. Clutch Linkage 1500 Model Front Axle (4X4) 1500 Model Rear Axle 2500/3500 Model Front and Rear Axle...
Page 383 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..384 Maintenance Schedules ....384 Schedule “B” ......387 Schedule “A”...
Page 384: Emission Control System Maintenance
384 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 385 • Heavy Loading. • Taxi, police, or delivery service (commercial service). • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B”...
Page 386 386 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 387: Schedule "B" 387
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 388 388 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 389 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 390 390 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 391 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Drain and refill transfer case fluid (4X4). Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 392 392 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Inspect engine air cleaner filter. Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect auto tension drive belt and replace if re- quired.
Page 393 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Change rear axle fluid. Change front axle fluid (4X4). Check transfer case fluid level (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary.
Page 394 394 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Flush and replace engine coolant. Flush and replace Power Steering Fluid. Inspect brake linings. 93,000 96,000 99,000 (149 000) (154 000) (158 000) 100,000...
Page 395 Miles (Kilometers) Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Drain and refill transfer case fluid (4X4). Change rear axle fluid. Change front axle fluid (4X4). Inspect brake linings. Inspect engine air cleaner filter, replace if necessary.
Page 396 396 SCHEDULE “B” Miles (Kilometers) Drain and refill automatic tranmission fluid and change main sump filter (45RFE/545RFE only). * This maintenance is recommended by the manufacture to the owner but is not required to maintain the emis- sions warranty. ‡ This maintenance is not required if previously replaced. 105,000 108,000 111,000...
Page 397: Schedule "A" 397
Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Check transfer case fluid level (4X4). Lubricate outer tie rod ends 2500/3500 (4X4) mod- els only. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. 6,000 12,000 18,000 (10 000)
Page 398 398 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Check transfer case fluid level (4X4). Lubricate outer tie rod ends 2500/3500 (4X4) models only. Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter.
Page 399 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Check transfer case fluid level (4X4). Flush and replace Power Steering Fluid. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect PCV valve, replace as necessary.
Page 400 400 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Drain and refill transfer case fluid (4X4). Flush and replace engine coolant, if not done at 60 mos. Lubricate outer tie rod ends 2500/3500 (4X4) models only. Inspect brake linings.
Page 401 WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 403: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......404 Prepare For The Appointment .
Page 404: Suggestions For Obtaining Service For Your Vehicle
404 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 405 The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf.
Page 406 406 IF YOU NEED CONSUMER ASSISTANCE In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY) To assist customers who have hearing difficulties, the manufacturer has installed special TDD (Telecommuni-...
Page 407: Warranty Information
Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in those documents. We appreciate that you have made a major investment when you purchased your new vehicle. Your dealer has also made a major investment in facilities, tools, and training to assure that you are absolutely delighted with your ownership experience.
Page 408 408 IF YOU NEED CONSUMER ASSISTANCE...
Page 409: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 410: Publication Order Forms
410 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 411 IF YOU NEED CONSUMER ASSISTANCE 411 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals...
Page 413 INDEX...
Page 414 414 INDEX Adding Fuel ......259,295 Air Cleaner, Engine ....334,357 Air Conditioner Maintenance .
Page 415 B-Pillar Location ......239 Brake Fluid ......382 Brake System .
Page 416 416 INDEX Climate Control ......185 Clock ....... . 151 Clutch .
Page 417 Disposal Engine Oil ......347 Door Ajar ......145 Door Locks .
Page 418 418 INDEX Exhaust System ..... . . 69,343 Exterior Lighting ......101 Filters Air Cleaner .
Page 419 Fuel, Flexible ... . . See Flexible Fuel Vehicles Fueling ....... 259 Fuses .
Page 420 420 INDEX Hub Caps ......308 Ignition ......14,204 Key .
Page 421 Courtesy/Reading ..... 113 Cruise ......147 Daytime Running .
Page 422 422 INDEX Lumbar Support ......94 Maintenance ......327 Maintenance Free Battery .
Page 423 Dipstick ......329 Disposal ......332 Filter .
Page 424 424 INDEX Pretensioners Seat Belts ......42 Programmable Electronic Features ..121,125 Programming Transmitters .
Page 425 Seat Belts ......33,34,70 Adjustable Upper Shoulder Anchorage ..41 And Pregnant Women .
Page 426 426 INDEX Spark Plugs ......333 Speed Control ......109 Speedometer .
Page 427 Inflation Pressures ..... 244 Jacking ......302 Load Capacity .
Page 428 428 INDEX Shifting ......208 Transmitter, Garage Door Opener ... . 120 Tread Wear Indicators .
Page 429 INDEX 429 Wiper Blade Replacement ....342 Wipers, Intermittent ..... . 105...

Dodge 2004 Ram 1500 Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Dodge 2004 Ram 1500

Summary of Contents for Dodge 2004 Ram 1500