Page 1: Table Of Contents
TABLE OF CONTENTS SECTION ............. 3 INTRODUCTION THINGS TO KNOW BEFORE STARTING YOUR VEHICLE UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 3 CONTENTS Introduction ......4 How To Use This Manual ....4 Warnings And Cautions .
Page 4: Introduction
4 INTRODUCTION INTRODUCTION This manual has been prepared with the assistance of service and engineering specialists to acquaint you with the operation and maintenance of your new vehicle. It is supplemented by a Warranty Information Booklet and various customer oriented documents. You are urged to read these publications carefully.
Page 5: Van Conversions/Campers
WARNINGS AND CAUTIONS This manual contains WARNINGS against operating procedures which could result in an accident or bodily injury. It also contains CAUTIONS against procedures which could result in damage to your vehicle. If you do not read this entire manual you may miss important information.
Page 6: Vehicle Identification Number
This number also appears on the Automobile Information Disclosure Label affixed to a window on your vehicle. Save this label for a convenient record of your vehicle identification number and optional equipment.
Page 7: Vehicle Modifications / Alterations
INTRODUCTION 7 VEHICLE MODIFICATIONS / ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to an accident resulting in serious injury or death.
Page 9 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....11 Key-In-Ignition Reminder ....11 Sentry Key —...
Page 10 10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To Disarm The System ....25 Windows ......26 Power Windows—If Equipped .
Page 11: Things To Know Before Starting Your Vehicle 9
A WORD ABOUT YOUR KEYS The double sided keys may be inserted into the locks with either side up. The keys for your new vehicle are enclosed in a plastic bag with a bar code label affixed to the front. The bar code can be used to order duplicate keys from your dealer or a locksmith.
Page 12: 12 Things To Know Before Starting Your Vehicle
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Security Light , located in the instrument cluster, will illuminate for about 2 seconds when the ignition switch is first turned to the ON position. If the vehicle electronics do not receive a valid signal from the ignition key, the Security Light will flash continuously to signal that the vehicle has been immobilized.
Page 13 Customer Key Programming You can program new keys to the system if you have two valid keys by doing the following: 1. Insert the first valid key into the ignition and turn the ignition to the ON position for at least 3 seconds but no longer than 15 seconds.
Page 14: Ignition And Steering Lock - If Equipped
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE IGNITION AND STEERING LOCK — IF EQUIPPED Manual Transmissions Depress and hold the release button located between the ignition switch and the instrument panel. Turn the igni- tion key to LOCK and remove the key. Manual Transmissions DOOR KEY The same key used to start the vehicle is also used to...
Page 15 WARNING! When leaving the vehicle always remove the key from the ignition lock, and lock your vehicle. Do not leave children unattended in the vehicle, or with access to an unlocked vehicle. Unsupervised use of vehicle equipment may cause severe personal inju- ries and death.
Page 16 16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a safety feature the doors will not lock when using the door lock switches during the following condition: 1. The driver’s door is open while the key is in the ignition. Central Locking —...
Page 17: Remote Keyless Entry - If Equipped
2. Fasten your seat belt (Fastening the seat belt will cancel any chiming that may confuse you during this programming procedure). 3. Place the key into the ignition. 4. Within 10 seconds cycle the key from the OFF position to the ON position four times; ending in the ON position ( Do not start the engine ).
Page 18: To Unlock The Doors
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE To unlock the doors: Press and release the UNLOCK button on the key fob once to unlock only the driver’s door or twice to unlock all the doors. When the UNLOCK button is pressed, the illuminated entry will initiate, the parking lights will flash on twice and if installed, the cargo lamp will turn on for 30 seconds.
Page 19: To Lock The Doors
To lock the doors: Press and release the LOCK button on the transmitter to lock all doors. If the ignition is OFF, when the doors are locked, the parking lights will flash on once and the horn will chirp once. The horn chirp feature will be shipped from the assembly plants activated.
Page 20: Using The Panic Alarm
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Fasten your seat belt (fastening the seat belt will cancel any chiming that may confuse you during this program- ming procedure). 3. Place the key into the ignition. 4. Turn the ignition to the ON position ( Do not start the engine ).
Page 21: Programming Additional Transmitters
Programming Additional Transmitters Vehicles with the keyless entry option will be shipped from the assembly plants with two key fob transmitters programmed only for that vehicle. A total of four fobs can be programmed for your vehicle. Additional fobs can be programmed to your vehicle through the use of a cur- rently programmed fob.
Page 22: General Information
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11. A single chime will be heard. The chime indicates that the fob has been programmed. 12. Repeat steps 8 to 11 for a total of 4 fobs. 13. Turn the ignition to the OFF position or wait 60 seconds to exit program mode.
Page 23: Transmitter Battery Service
Transmitter Battery Service The recommended replacement battery is a 3V lithium 2016 cell. This transmitter requires two batteries. NOTE: Do not touch the battery terminals that are on the back housing or the printed circuit board. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 1.
Page 24: Security Alarm System - If Equipped
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE SECURITY ALARM SYSTEM — IF EQUIPPED This system monitors the vehicle doors and ignition for unauthorized operation. When the alarm is activated, the system provides both audible and visual signals. For the first 3 minutes the horn will sound and the headlights and security telltale will flash repeatedly.
Page 25: To Disarm The System
To Disarm the System: Use the Keyless Entry transmitter or the key to turn the driver’s door lock to the unlock position. If something has triggered the system in your absence, the horn will sound three times when you unlock the doors and the security lamp will flash for 30 seconds.
Page 26: Windows
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WINDOWS Power Windows—If Equipped The control on the left front door panel has up-down switches that give you fingertip control of all power windows. There is a single opening and closing switch on the front passenger door for passenger window control.
Page 27: Sliding Rear Window
Auto Down (Driver’s Side Only) The driver’s window switch has an Auto Down feature. Press the window switch past the detent, release, and the window will go down automatically. Sliding Rear Window A locking device in the center of the window helps to prevent entry from the rear of the vehicle.
Page 28: Lap/Shoulder Belts
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, you and your passengers can suffer much greater injuries if you are not properly buck- led up. You can strike the interior of your vehicle or other passengers, or you can be thrown out of the vehicle.
Page 29 WARNING! It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and seat belts.
Page 30 30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is above the back of the seat. Grasp the latch plate and pull out the belt. Slide the latch plate up the webbing as far as necessary to allow the belt to go around your lap.
Page 31 WARNING! • A belt buckled into the wrong buckle will not protect you properly. The lap portion could ride too high on your body, possibly causing internal injuries. Always buckle your belt into the buckle nearest you. • A belt that is too loose will not protect you as well. In a sudden stop you could move too far forward, increasing the possibility of injury.
Page 32 32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • A lap belt worn too high can increase the risk of internal injury in a collision. The belt forces won’t be at the strong hip and pelvic bones, but across your abdomen.
Page 33 Standard Cab Front Center Three Point Belt 1. The front center seat belt on the Standard Cab may be disconnected to open up utilization of the storage areas behind the front seats. The black latch plate can be detached from the black keyed seat belt buckle located on the inboard side of the passenger seat.
Page 34 34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • If the black latch and black buckle are not prop- erly connected when the seat belt is used by an occupant, the seat belt will not be able to provide proper restraint and will increase the risk of injury in a collision.
Page 35: Adjustable Upper Shoulder Belt Anchorage
In Use Position WARNING! If the black latch and buckle are not connected when the seat belt is used by an occupant, the seat belt will not restrain you properly. THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 Adjustable Upper Shoulder Belt Anchorage In the front row outboard seats, the shoulder belt can be adjusted upward or downward to help position the belt away from your neck.
Page 36: Automatic Locking Mode (If Equipped)
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE As a guide, if you are shorter than average, you will prefer a lower position, and if you are taller than average, you’ll prefer a higher position. When you release the anchorage, try to move it up or down to make sure that it is locked in position.
Page 37: Enhanced Driver Seat Belt Reminder System (Beltalert)
NOTE: These devices are not a substitute for proper seat belt placement by the occupant. The seat belt still must be worn snugly and positioned properly. The pretensioners are triggered by the airbag control module. Like the airbags, the pretensioners are single use items.
Page 38: Seat Belts And Pregnant Women
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Within 60 seconds of starting the vehicle, unbuckle and then re-buckle the driver’s seat belt at least three times within 10 seconds, ending with the seat belt buckled. 4. Turn off the engine. A single chime will sound to signify that you have successfully completed the pro- gramming.
Page 39: Driver And Right Front Passenger Supplemental Restraint System (Srs)-Airbag
WARNING! Using a seat belt extender when not needed can increase the risk of injury in a collision. Only use the seat belt extender when the lap belt is not long enough when it is worn low and snug, and in the recommended seating positions.
Page 40 40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! • Do not put anything on or around the airbag covers or attempt to manually open them. You may damage the airbags and you could be injured because the airbags are not there to protect you. These protective covers for the airbag cushions are designed to open only when the airbags are inflating.
Page 41 • Infants in rear facing child restraints must NEVER ride in the front seat of a vehicle with a passenger front airbag unless the airbag is turned off (Standard Cab Vehicles Only). An airbag deployment can cause se- vere injury or death to infants in that position. See the Passenger Airbag On/Off Switch section.
Page 42 42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Airbag System Components The airbag system consists of the following: • Airbag Control Module • AIRBAG Readiness Light • Driver Airbag • Passenger Airbag • Steering Wheel and Column • Instrument Panel •...
Page 43 How The Airbag System Works • The airbag control module determines if a frontal collision is severe enough to require the airbags to inflate. • The airbag control module will not detect roll over, or rear collisions. • The airbag control module also monitors the readiness of the electronic parts of the system whenever the ignition switch is in the RUN position.
Page 44 44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • When the airbag control module detects a collision requiring the airbags, it signals the inflator units. A large quantity of nontoxic gas is generated to inflate the airbags. The airbag covers separate and fold out of the way as the airbags inflate to their full size.
Page 45 • is a child, age 1 to 12 who must ride in the front seat because there is no rear seat, because there is no rear seat position available, or because the child has a medical condition which makes it necessary for the driver to be able to see the child, •...
Page 46 46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If A Deployment Occurs The airbag system is designed to deploy when the air bag control module detects a moderate-to-severe frontal col- lision, and then immediately to deflate. NOTE: A frontal collision that is not severe enough to need airbag protection will not activate the system.
Page 47 WARNING! Deployed airbags can’t protect you in another colli- sion. Have the airbags replaced by an authorized dealer as soon as possible. Window Airbags Supplemental Restraint System (SRS)—If Equipped The window airbag control module determines if a side collision is severe enough to require the side airbags to inflate.
Page 48 48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Enhanced Accident Response System If the airbags deploy after an impact and the electrical system remains functional, vehicles equipped with power door locks will unlock automatically. In addition, approximately 10 seconds after the vehicle has stopped moving, the interior lights will light until the ignition switch is turned off.
Page 49: Child Restraint
Airbag Light You will want to have the airbags ready to inflate for your protection in an impact. While the airbag system is designed to be maintenance free, if any of the following occurs, have an authorized dealer service the system promptly: •...
Page 50 50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! In a collision, an unrestrained child, even a tiny baby, can become a missile inside the vehicle. The force required to hold even an infant on your lap can become so great that you could not hold the child, no matter how strong you are.
Page 51 • Children who weigh more than 20 lbs (9 kg) and who are older than one year can ride forward-facing in the vehicle. Forward-facing child seats and convertible child seats used in the forward-facing direction are for children who weigh 20 to 40 lbs (9 to 18 kg) and who are older than one year.
Page 52 52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Here are some tips for getting the most out of your child restraint: • Before buying any restraint system, make sure that it has a label certifying that it meets all applicable Safety Standards.
Page 53 • If the belt still can’t be tightened, or if pulling and pushing on the restraint loosens the belt, disconnect the latch plate from the buckle, turn the buckle around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, try a different seating position.
Page 54 54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The LATCH lower anchorage bars are located where the seatback meets the seat cushion. If the lower anchorage bars are not visible, identification dots are located above the standard cab front seat lower anchorages as a guide for locating the lower anchors.
Page 55 Installing the Child Restraint System We urge that you carefully follow the directions of the manufacturer when installing your child restraint. Many, but not all, restraint systems will be equipped with separate straps on each side, with each having a hook or connector and a means for adjusting the tension in the strap.
Page 56 56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! An incorrectly anchored tether strap could lead to seat failure and injury to the child. In a collision, the seat could come loose and allow the child to crash into the inside of the vehicle or other passengers, or even be thrown from the vehicle.
Page 57: Engine Break-In Recommendations
Children Too Large for Booster Seats Children who are large enough to wear the shoulder belt comfortably, and whose legs are long enough to bend over the front of the seat when their back is against the seat back should use the lap/shoulder belt in a rear seat. •...
Page 58: Safety Tips
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Wait until the engine has reached normal operating temperature before driving at the recommended maxi- mum break-in speed. • Avoid excessive idling. • Check the engine oil level at every fuel fill. NOTE: A new engine will consume some oil during the first few thousand miles of operation.
Page 59: Exhaust Gas
Exhaust Gas WARNING! Exhaust gases contain carbon monoxide, a poten- tially toxic gas that by itself is colorless and odorless. To avoid inhaling these gases, the following precau- tions should be observed: • Do not run the engine in a closed garage or in confined areas any longer than needed to move your vehicle in or out of the area.
Page 60: Safety Checks You Should Make Inside The Vehicle
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The Vehicle Seat Belts Inspect the belt system periodically, checking for cuts, frays and loose parts. Damaged parts must be replaced immediately. Do not disassemble or modify the system. Seat belt assemblies must be replaced after an accident if they have been damaged (bent retractor, torn webbing, etc.) or if the front airbags have deployed.
Page 61: Understanding The Features Of Your Vehicle
UNDERSTANDING THE FEATURES OF YOUR VEHICLE CONTENTS Mirrors .......65 Automatic Dimming Mirror— If Equipped ..65 Outside Mirrors .
Page 62 62 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Open And Close The Hood ....84 Lights ....... .86 Interior Lights .
Page 63 To Accelerate For Passing ....98 Overhead Console ..... . .99 Courtesy/Reading Lights .
Page 64 64 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Cupholders ......114 Front Cupholders ..... 114 Storage .
Page 65: Mirrors
MIRRORS Automatic Dimming Mirror— If Equipped This mirror automatically adjusts for annoying headlight glare from vehicles behind you. You can turn the feature on or off by pressing the button at the base of the mirror. A light in the button will indicate when the dimming feature is activated.
Page 66: Exterior Mirrors Folding Feature
66 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in a right side convex mirror will look smaller and farther away than they really are. Relying too much on your right side convex mirror could cause you to collide with an- other vehicle or other object.
Page 67: Electric Rear Window Defroster And Heated Sideview Mirrors - If Equipped
Set the top switch to the left or right for the left or right mirror, and set it to the center off position to prevent accidentally moving a mirror when you are finished adjusting the mirror. To adjust a mirror, select left or right with the top switch, and press one of the four arrows for the direction you want the mirror to move.
Page 68 68 UNDERSTANDING THE FEATURES OF YOUR VEHICLE UConnect™ allows you to transfer calls between the system and your cellular phone as you enter or exit your vehicle, and enables you to mute the system’s micro- phone for private conversations. The UConnect™; phone book enables you to store up to 32 names and four numbers per name.
Page 69: Operation
The UConnect™ system is fully integrated into your vehicle, including your vehicle’s stereo system. All voice prompts as well as the other party’s voice in a conversa- tion will be played over your vehicle’s stereo system. The volume of the UConnect™ system can be controlled through your normal stereo controls.
Page 70 70 UNDERSTANDING THE FEATURES OF YOUR VEHICLE enter into your cellular phone during the cellular phone pairing process. You can enter any four-digit pin number. You will not need to remember this pin number after the initial registration process. • The UConnect™ system will then prompt you to begin the cellular phone pairing process on your cellular phone.
Page 71 • After the Ready prompt, say Dial or Call followed by the name and designation of a phonebook entry that you wish to dial. For example, you can say Call John Doe Work . Add Names to Your UConnect™ Phonebook •...
Page 72 72 UNDERSTANDING THE FEATURES OF YOUR VEHICLE After you are finished editing an entry in the phonebook, you will be given the opportunities to edit another entry in the phonebook, call the number you just edited, or return to the main menu. Phonebook edit can be used to add another phone number to a name entry that already exists in the phonebook.
Page 73: Phone Call Features
List All Names in the UConnect™ Phonebook • Press the ’Phone’ button to begin. • After the Ready prompt, say Names . • The UConnect™ system will play the names of all the phonebook entries. • To call one of the names in the list, press the ’Voice Recognition’...
Page 74 74 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Answer or Reject an Incoming Call - Call Currently in Progress If a call is currently in progress and you have another incoming call, press the ’Phone’ button to place the current call on hold and answer the incoming call. To reject the incoming call, you can disregard the call and continue with your current conversation.
Page 75: Advanced Phone Connectivity
Three-Way Calling To initiate three-way calling, press the ’Voice Recogni- tion’ button while a call is in progress and make a second phone call. When the second call is established, press the ’Phone’ button until you hear a double beep indicating that the two calls have been joined into one conference call.
Page 76 76 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • You will be asked to say the name of the phone that you wish to delete. You can either say the name of the phone that you wish to delete or you can say All to delete all the phones.
Page 77: Uconnect™ System Features
• The lower priority phone will only be used for the next phone call. After that, the UConnect™ system will return to using the highest priority phone in the vehicle. UConnect™ System Features Barge In - Touch Tone Phone Inputs You can use your UConnect™...
Page 78 78 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Turning Confirmation Prompts On/Off Turning confirmation prompts off will stop the system from confirming your choices (e.g. the UConnect™ sys- tem will not repeat a phone number before you dial it). • Press the ’Phone’ button to begin. •...
Page 79: Seats
Help If you need assistance at any prompt or if you want to know what your options are at any prompt, say Help . The UConnect™ system will play all the options at any prompt if you ask for help. Cancel At any prompt, you can say Cancel and you will be returned to the previous menu.
Page 80: 40-20-40 Front Seat
80 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Adjusting a seat while the vehicle is moving is dangerous. The sudden movement of the seat could cause you to lose control. The seat belt might not be properly adjusted and you could be injured. Adjust any seat only while the vehicle is parked.
Page 81 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 81 Up, Down, Forward, and Rearward...
Page 82: Manual Passenger Seat
82 UNDERSTANDING THE FEATURES OF YOUR VEHICLE The power seat controls are on the outboard side of the front seat cushions. Three switches control the seat move- ment. The four-way switch in the center can be moved forward or backwards to get the most comfortable posi- tion.
Page 83: Manual Seatback Recline
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 83 Manual Seatback Recline The recliner mechanism control is on the outboard side of the seat. To recline, lean forward slightly, lift the lever, then push back to the desired position and release the lever.
Page 84: Adjustable Head Restraints
84 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjustable Head Restraints Head restraints can reduce the risk of whiplash injury in the event of impact from the rear. Pull up or push down on the restraints so that the upper edge is as high as practical, at least to the level of the ears.
Page 85 To prevent possible damage, do not slam the hood to close it. Use a firm downward push at the front center of the hood to ensure that both latches engage. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 85 WARNING! If the hood is not fully latched, it could fly up when the vehicle is moving and block your forward vision.
Page 86: Lights
86 UNDERSTANDING THE FEATURES OF YOUR VEHICLE LIGHTS Interior Lights Courtesy/ dome lights are turned on when the front doors are opened, when the dimmer control (rotating wheel on the right side of the switch) is rotated to the second upward detent position, or if equipped, when the UNLOCK button is pressed on the key fob.
Page 87: Battery Saver
turn on the cargo light located on the back of the cab. When a door is open and the interior lights are on, rotating the dimmer control all the way down to the OFF detent will cause all the interior lights to go out. This is also known as the Party mode because it allows the doors to stay open for extended periods of time without discharging the vehicle’s battery.
Page 88: Headlamp Delay - If Equipped
88 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlamp Delay — If Equipped To aid in your exit, your vehicle, if equipped, can be programmed by your dealer with a headlamp delay that will leave the headlamps on for 0, 30, 60, or 90 seconds. This delay is initiated when the ignition is turned OFF while the headlamp switch is on, and then the headlamp switch is cycled off.
Page 89: Daytime Running Lights (Canada And Fleet Vehicles Only)
To minimize the possibility of scratching the lenses and reducing light output, avoid wiping with a dry cloth. To remove road dirt, wash with a mild soap solution fol- lowed by rinsing. Do not use abrasive cleaning components, solvents, steel wool or other abrasive materials to clean the lenses.
Page 90: Cargo Light
90 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CARGO LIGHT The cargo lights are turned on by rotating the dimmer control to the optional fully upward position. The cargo lights will also turn on for 30 seconds when a key fob Unlock is pressed, as part of the illuminated entry feature.
Page 91: Passing Light
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 91 Passing Light You can signal another vehicle with your headlights by partially pulling the multifunction lever toward the steer- ing wheel. This will cause the high beam headlights to turn on until the lever is released. High Beam / Low Beam Select Switch Pull the multifunction control lever fully toward the steering wheel to switch the headlights from HIGH or...
Page 92: Windshield Wipers
92 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Windshield Wipers The wipers and washers are operated by a switch in the multifunction control lever. Turn the end of the handle to select the desired wiper speed. Intermittent Wiper System The intermittent feature of this system was designed for use when weather conditions make a single wiping cycle, with a variable pause between cycles, desirable.
Page 93: Windshield Washers
The delay interval decreases as you rotate the knob until it enters the LO continual speed position. The delay can be regulated from a maximum of about 15 seconds between cycles, to a cycle every 2 seconds. The delay intervals will double in duration when the vehicle speed is 10 mph (16 km) or less.
Page 94: Tilt Steering Column
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE TILT STEERING COLUMN To tilt the column, push down on the lever below the turn signal control and move the wheel up or down, as desired. Push the lever back up to lock the column firmly in place.
Page 95: Driver Adjustable Pedals
DRIVER ADJUSTABLE PEDALS The power adjustable accelerator and brake pedals allow the driver to establish a comfortable position relative to the steering wheel and pedals. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Adjustment 1. Position the driver seat so that you are at least 10 inches (254 mm) away from the airbag located in the center of the steering wheel.
Page 96: Electronic Speed Control
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CAUTION! Do not place any article under the adjustable pedals or impede its ability to move as it may cause damage to the pedal controls. Pedal travel may become limited if movement is stopped by an obstruction in the adjustable pedal’s path.
Page 97: To Set At A Desired Speed
To Set At A Desired Speed When the vehicle has reached the desired speed, press and release the SET button. Release the accelerator and the vehicle will operate at the selected speed. To Deactivate A soft tap on the brake pedal, normal braking, clutch pressure while slowing the vehicle, or pressing the CAN- CEL button will deactivate speed control without erasing the memory.
Page 98: To Accelerate For Passing
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To decrease speed while the speed control is on, press and hold the COAST button. Release the button when the desired speed is reached, and the new speed will be set. To Accelerate For Passing Depress the accelerator as you would normally.
Page 99: Overhead Console
OVERHEAD CONSOLE The overhead console consists of the following features: • Courtesy/Reading Lights • Compass/Temperature Mini-Trip Computer (CMTC) • Universal Garage Door Opener UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Courtesy/Reading Lights In the middle of the console are two courtesy/reading lights.
Page 100: Compass/Temperature Mini-Trip Computer
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE COMPASS/TEMPERATURE MINI-TRIP COMPUTER This overhead console consists of the following: • Courtesy Lights • Compass/Temperature Mini-Trip Computer • Universal Garage Door Opener This overhead console allows you to choose between a compass/temperature display and one of four trip con- ditions being monitored.
Page 101: Reset Button
RESET Button Use this button to reset the following displays to zero: Average Fuel Economy Trip Odometer Elapsed time UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Global Reset If the RESET button is pressed twice within 4 seconds while in any of the 3 resettable displays, the Global Reset will reset all 3 displays.
Page 102: Average Fuel Economy (Avg Eco)
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Average Fuel Economy (AVG ECO) Shows the average fuel economy since the last reset. This display mode becomes less sensitive to instantaneous changes in fuel consumption as the number of total vehicle miles since the last reset increases. It is suggested that this mode be reset periodically for general operation or when driving conditions change significantly (for example, at the end of a trip or when a trailer is...
Page 103: Elapsed Time (Et)
Elapsed Time (ET) This display shows the accumulated ignition ON time since the last reset. C/T Button Use this button to select a readout of the outside tem- perature and one of eight compass headings that indicate the direction in which the vehicle is facing. UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 WARNING! Even if the display still reads a few degrees above...
Page 104: Manual Compass Calibration
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Manual Compass Calibration NOTE: To ensure proper compass calibration, make sure the compass variance is properly set before manu- ally calibrating the compass. If the compass appears erratic and the CAL symbol does not appear, you must manually put the compass into the “Calibration”...
Page 105: Outside Temperature
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 To set the variance: Turn the ignition ON and set the display to “Compass/Temperature.” Press the RESET button approximately five seconds. The last variance zone number will be displayed. Press the STEP button to select the new variance zone and press the RESET button to resume normal operation.
Page 106: Garage Door Opener
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE GARAGE DOOR OPENER The HomeLink Universal Transceiver replaces up to three remote controls (hand held transmitters) that oper- ate devices such as garage door openers, motorized gates, or home lighting. It triggers these devices at the push of a button.
Page 107: Programming Homelink
Programming HomeLink NOTE: When programming a garage door opener, it is advised to park outside the garage. Some vehicles may require the ignition switch to be turned to the second (or accessories ) position for programming and/or opera- tion of HomeLink. It is also recommended that a new battery be placed in the hand-held transmitter of the device being programmed to HomeLink for quicker training and accurate transmission of the radio-frequency...
Page 108 108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Your motorized door or gate will open and close while you are training the Universal Transceiver. Do not train the transceiver if people or pets are in the path of the door or gate. A moving door or gate can cause serious injury or death to people and pets or damage to objects.
Page 109: Canadian Programming/Gate Programming
If the indicator light blinks rapidly for two seconds and then turns to a constant light, continue with Program- ming steps 6-8 to complete the programming of a rolling code equipped device (most commonly a garage door opener). 6. At the garage door opener receiver (motor-head unit) in the garage, locate the learn or smart button.
Page 110: Using Homelink
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you live in Canada or you are having difficulties programming a gate operator by using the Program- ming procedures (regardless of where you live), replace Programming HomeLink step 3 with the following: NOTE: If programming a garage door opener or gate operator, it is advised to unplug the device during the cycling process to prevent possible overheating.
Page 111: Reprogramming A Single Homelink Button
Reprogramming a Single HomeLink Button To program a device to HomeLink using a HomeLink button previously trained, follow these steps: 1. Press and hold the desired HomeLink button. Do NOT release the button. 2. The indicator light will begin to flash after 20 seconds. Without releasing the HomeLink button, proceed with Programming step 2 For questions or comments, contact HomeLink at:...
Page 112: Electrical Power Outlets
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE ELECTRICAL POWER OUTLETS The auxiliary electrical outlets can provide power for in cab accessories designed for use with the standard “cigar lighter” plugs. One of the outlets is the cigar lighter outlet, located in the instrument panel below the ash receiver.
Page 113: Cigar Lighter And Ash Receiver
CIGAR LIGHTER AND ASH RECEIVER The ash receiver is opened and closed by pushing on the front surface of the receiver and then allowing the receiver to open. The cigar lighter is located in the instrument panel below the ash receiver. NOTE: This outlet has a fused direct feed from the battery so it receives power whether the ignition is ON or OFF.
Page 114: Cupholders
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS Front Cupholders The cupholders consist of two cupwells for passenger convenience. STORAGE Center Storage Compartment The center portion of the seat folds down to provide an armrest with unique storage compartments under the lid. Push the button on the front of the armrest to raise the cover.
Page 115: Storage And Seats
configure the storage area into compartments. For ex- ample, compartments can be configured to hold a lap-top computer, a cellular telephone, CD’s and miscellaneous items. The top of the cover provides a generous firm surface to serve as a desktop for your “mobile office.” WARNING! •...
Page 116: Pickup Box
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There is also storage behind the seat. This storage area contains the 10 inch subwoofer (if equipped). PICKUP BOX The pickup box on your new Ram has many features designed for utility and convenience. NOTE: If you are installing a toolbox to the front of the pickup box, you must use Mopar available from you dealer.
Page 117 You can carry wide building materials (sheets of ply- wood, etc.) by building a raised load floor. Place lumber across the box in the indentations provided above the wheel housings and in the bulkhead dividers to form the floor. WARNING! The pickup box is intended for load carrying pur- poses only, not for passengers, who should sit in seats and use seat belts.
Page 118: Slide-In Campers
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE There are stampings in the sheet metal on the inner side bulkheads of the box in front of and behind both wheel housings. Place wooden boards across the box from side to side to create separate load compartments in the pickup box.
Page 119 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119...
Page 121: Understanding Your Instrument Panel
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instruments And Controls ....122 Instrument Cluster ..... . 123 Instrument Cluster Description .
Page 122: Instruments And Controls
122 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENTS AND CONTROLS...
Page 123: Instrument Cluster
UNDERSTANDING YOUR INSTRUMENT PANEL 123 INSTRUMENT CLUSTER...
Page 124: Instrument Cluster Description
124 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTION 1. Malfunction Indicator Light This light is part of an onboard diagnostic system which monitors the emissions and engine control system. If the vehicle is ready for emissions testing the light will come on when the ignition is first turned on and remain on, as a bulb check, until the engine is started.
Page 125 2. Voltage Gauge When the engine is running, the gauge indicates the electrical system voltage. The pointer should stay within the normal range if the battery is charged. Typically this would be between 12 and 14 volts. If the pointer moves to either extreme left or right and remains there during normal driving, the electrical system should be serviced.
Page 126 126 UNDERSTANDING YOUR INSTRUMENT PANEL unbuckled, a chime will sound. After the bulb check or when driving, if the driver seat belt remains unbuckled, the Seat Belt Warning Light will flash or remain on continuously. Refer to Enhanced Driver Seat Belt Re- minder System (BeltAlert) in the Occupant Restraints section for more information.
Page 127 12. Temperature Gauge The temperature gauge indicates engine coolant temperature. Any reading within the normal range (less that the red zone) indicates that the cooling system is operating satisfactorily. The gauge needle will likely indicate a higher temperature when driving in hot weather, up mountain grades, in heavy traffic.
Page 128 128 UNDERSTANDING YOUR INSTRUMENT PANEL 15. CHECK GAGES This light illuminates when the Voltmeter, Engine Oil Pressure or Engine Coolant Temperature gages indicate a reading either too high or too low. Examine the gages carefully, and follow the instructions above for each indicated problem. NOTE: When the ignition switch is turned to OFF, the Fuel Gage, Voltmeter, Oil Pressure and Engine Coolant Temperature gages may not show accurate readings.
Page 129 17. ABS Warning Light This light monitors the Anti-Lock Brake System which is described elsewhere in this manual. This light will come on when the ignition key is turned to the ON position and may stay on for five seconds. If the ABS light remains on or comes on during driving, it indicates that the anti-lock portion of the brake system is not functioning and that service is required.
Page 130 130 UNDERSTANDING YOUR INSTRUMENT PANEL 19. LAMP OUT Light The LAMP OUT indicator in the instrument cluster alerts the driver if a defective bulb or wiring circuit is detected for most of the exterior lamps - headlamps, turn signal lamps, and stop lamps. 20.
Page 131: Electronic Digital Clock
24. Oil Temperature Gauge – if equipped This gauge shows the oil temperature. The gauge pointer will likely show higher temperatures when driving in hot weather, up mountain grades, or in heavy stop and go traffic. If this gauge reaches the red zone you should stop the vehicle, shift into Neutral, and increase the engine idle speed for 2 to 3 minutes.
Page 132: Sales Code Rbq-Am/Fm Stereo Radio With 6 - Disc Cd Changer
132 UNDERSTANDING YOUR INSTRUMENT PANEL SALES CODE RBQ—AM/FM STEREO RADIO WITH 6 - DISC CD CHANGER Radio Operation Power/Volume Control Press the PWR/VOL control to turn the radio on. Turn the volume control clockwise to increase the volume. NOTE: Power to operate the radio is controlled by the ignition switch.
Page 133 Seek Press and release the SEEK button to search for the next station in either the AM or FM mode. Press the top of the button to seek up and the bottom to seek down. The radio will remain tuned to the new station until you make another selection.
Page 134: Cd Player Operation
134 UNDERSTANDING YOUR INSTRUMENT PANEL 5 seconds after pressing the SET RND button, the station will continue to play but will not be locked into push- button memory. You may add a second station to each push-button by repeating the above procedure with this exception: Press the SET button twice and SET 2 will show in the display window.
Page 135 Inserting The Compact Disc CAUTION! This CD player will accept 4 ⁄ inch (12 cm) discs only. The use of other sized discs may damage the CD player mechanism. You may either insert or eject a disc with the radio OFF. If you insert a disc with the ignition ON and the radio OFF, the display will show the time of day.
Page 136 136 UNDERSTANDING YOUR INSTRUMENT PANEL If you have ejected a disc and have not removed it within 15 seconds, it will be reloaded. If the CD is not removed, the radio will continue to play the non-removed CD. If the CD is removed and there are other CD’s in the radio, the radio will play the next CD.
Page 137 PTY (Program Type) Button Pressing this button once will turn on the PTY mode for 5 seconds. If no action is taken during the 5 second time out the PTY icon will turn off. Pressing the PTY button within 5 seconds will allow the program format type to be selected.
Page 138: Remote Sound System Controls
138 UNDERSTANDING YOUR INSTRUMENT PANEL By pressing the SEEK button when the PTY icon is displayed, the radio will be tuned to the next frequency station with the same selected PTY name. The PTY function only operates when in the FM mode. The radio display will flash “SEEK”...
Page 139: Radio Operation
The right hand control is a rocker type switch with a button in the center. Pressing the top of the switch will increase the volume and pressing the bottom of the switch will decrease the volume. The center button of the right hand control will allow you to change the mode.
Page 140: Radio Operation And Cellular Phones
140 UNDERSTANDING YOUR INSTRUMENT PANEL 2. If the disc is stained, clean the surface with a soft cloth, wiping from center to edge. 3. Do not apply paper or tape to the disc; avoid scratch- ing the disc. 4. Do not use solvents such as benzene, thinner, cleaners, or antistatic sprays.
Page 141: Climate Controls
CLIMATE CONTROLS Air Conditioning with Dual Zone Temperature Control With the Dual Zone Temperature Control System, each front seat occupant can independently control the tem- perature of air coming from the outlets on their side of the vehicle. UNDERSTANDING YOUR INSTRUMENT PANEL 141 Air Conditioning Operation To turn on the Air Conditioning, set the fan control at any speed and press the snowflake button located on the...
Page 142 142 UNDERSTANDING YOUR INSTRUMENT PANEL A/C Pushbutton With the fan control in the ON posi- tion, pushing the A/C button turns on the air conditioning compressor. An indicator light on the button shows that the Air Conditioning compressor is on. Conditioned air is now directed through the mode outlets selected.
Page 143 Bi-Level Air flows through the outlets located in the instru- ment panel and those located on the floor. NOTE: There is a difference in temperature between the upper and lower outlets for added comfort. The warmer air goes to the floor outlets. This feature gives improved comfort during sunny but cool conditions.
Page 144 144 UNDERSTANDING YOUR INSTRUMENT PANEL Dual Zone Temperature Control Use this control to regulate the temperature of the air inside the passenger compartment. This is accomplished by having separate temperature control slides for both the driver and front passenger. The blue area of the scale indicates cooler temperatures while the red area indicates warmer temperatures.
Page 145: Operating Tips
edges of the instrument panel. The demisters also pro- vide extra air ducts for circulation. They are in operation whenever the Floor, Mix or Defrost modes are in use. NOTE: When you turn off the engine you may hear a hissing sound from under the hood for a short period of time.
Page 146 146 UNDERSTANDING YOUR INSTRUMENT PANEL speeds will reduce fogging. Interior fogging on the windshield can be quickly removed by selecting the defrost mode. Regular cleaning of the inside of the windows with a non-filming cleaning solution (vinegar and water works very well) will help prevent contaminates (cigarette smoke, perfumes, etc.) from sticking to the windows.
Page 147: Operating Tips Chart
UNDERSTANDING YOUR INSTRUMENT PANEL 147 Operating Tips Chart...
Page 149 STARTING AND OPERATING CONTENTS Ignition/Starter Switch ....152 Lock ......152 Off .
Page 150 150 STARTING AND OPERATING Power Steering ......162 Tire Safety Information ....163 Tire Markings .
Page 151 Snowplow ......192 Dodge SRT-10 Models ....192 Traction .
Page 152: 152 Starting And Operating
152 STARTING AND OPERATING IGNITION/STARTER SWITCH LOCK Engages the steering wheel lock (if equipped) when the steering wheel is turned. Unlocks the steering wheel (if equipped with locking wheel). This is the normal running position. Allows the electrical accessories to be used when the engine is not running.
Page 153: Starting Procedures
STARTING AND OPERATING 153 STARTING PROCEDURES The starter should not be operated for more than 15- second intervals. Waiting a few seconds between such intervals will protect the starter from overheating. Manual Transmission Apply the parking brake, place the gearshift control lever in NEUTRAL and depress the clutch pedal to the floor before starting the vehicle.
Page 154: If Engine Fails To Start
154 STARTING AND OPERATING Normal starting of either a cold or a warm engine does not require pump- ing or depressing the accelerator pedal. To start the vehicle, turn the key to the ON position and press the red ENGINE START button located on the instrument panel and release when the engine starts.
Page 155: After Starting
WARNING! Never pour fuel or other flammable liquids into the throttle body air inlet opening in an attempt to start the vehicle. This could result in a flash fire causing serious personal injury. After Starting The idle speed is automatically controlled and will de- crease as the engine warms up.
Page 156 156 STARTING AND OPERATING Damage to the clutch can re- sult from starting in 2nd or 3rd gear with a loaded ve- hicle. Use each gear in nu- merical order – do not skip a gear. For improved clutch life, all six forward gears should be used.
Page 157: Limited-Slip Differential
MANUAL TRANSMISSION RECOMMENDED SHIFT SPEEDS (km/h) (24) (40) (65) Higher upshift speeds may be used to obtain a desired acceleration rate. Downshifting Moving from a high gear down to a lower gear is recommended to preserve brakes when driving down steep hills.
Page 158: Parking Brake
158 STARTING AND OPERATING The limited-slip differential is especially helpful during slippery driving conditions. With both rear wheels on a slippery surface, a slight application of the accelerator will supply maximum traction. When starting with only one rear wheel on an excessively slippery surface, slight momentary application of the parking brake may be necessary to gain maximum traction.
Page 159 Be sure the parking brake is firmly set when parked and the gear shift lever is in the REVERSE position. STARTING AND OPERATING 159 WARNING! • Always fully apply the parking brake when leav- ing your vehicle, or it may roll and cause damage or injury.
Page 160: Brake System
160 STARTING AND OPERATING When parking on a hill, turn the front wheels toward the curb on a downhill grade and away from the curb on an uphill grade. The parking brake should always be applied whenever the driver is not in the vehicle. BRAKE SYSTEM If power assist is lost for any reason (for example, repeated brake applications with the engine off), the...
Page 161 The system’s pump motor runs during an ABS stop to provide regulated hydraulic pressure. The pump motor makes a low humming noise during operation. This is normal. When you are in a severe braking condition involving use of the Anti-lock Brake System, you will experience some pedal drop as the vehicle comes to a complete stop.
Page 162: Power Steering
162 STARTING AND OPERATING WARNING! • Anti-lock system (ABS) cannot prevent the natu- ral laws of physics from acting on the vehicle, nor can it increase braking or steering efficiency be- yond that afforded by the condition of the vehicle brakes and tires or the traction afforded.
Page 163: Tire Safety Information
TIRE SAFETY INFORMATION Tire Markings NOTE: • P(Passenger)-Metric tire sizing is based on U.S. design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designation. Ex- ample: P215/65R15 95H. STARTING AND OPERATING 163 • European Metric tire sizing is based on European design standards.
Page 164 164 STARTING AND OPERATING Tire Sizing Chart Size Designation: P = Passenger car tire size based on U.S. design standards ...blank... = Passenger car tire based on European design standards LT = Light Truck tire based on U.S. design standards T = Temporary Spare tire 31 = Overall Diameter in Inches (in) 215 = Section Width in Milimeters (mm)
Page 165 Service Description: 95 = Load Index —A numerical code associated with the maximum load a tire can carry. H = Speed Symbol —A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions. —The maximum speed corresponding to the Speed Symbol should only be achieved un- der specified operating conditions.
Page 166: Tire Identification Number (Tin)
166 STARTING AND OPERATING Tire Identification Number (TIN) The TIN may be found on one or both sides of the tire however the date code may only be on one side. Tires with white sidewalls will have the full TIN including date code located on the white sidewall side of the tire.
Page 167: Tire Loading And Tire Pressure
Tire Loading and Tire Pressure Tire Placard Location NOTE: Some vehicles have a “Tire and Loading Infor- mation” placard located on the driver’s side “B” pillar. STARTING AND OPERATING 167 Tire and Loading Information Placard This placard tells you important information about the, 1) number of people that can be carried in the vehicle 2) the total weight your vehicle can carry 3) the tire size designed for your vehicle...
Page 168 168 STARTING AND OPERATING Loading The vehicle maximum load on the tire must not exceed the load carrying capacity of the tire on your vehicle. You will not exceed the tire’s load carrying capacity if you adhere to the loading conditions, tire size and cold tire inflation pressures specified on the Tire and Loading Information placard and the Vehicle Loading section of this manual.
Page 169 Steps for Determining Correct Load Limit 1. Locate the statement “The combined weight of occu- pants and cargo should never exceed XXX pounds” on your vehicle’s placard. 2. Determine the combined weight of the driver and passengers that will be riding in your vehicle. 3.
Page 170 170 STARTING AND OPERATING...
Page 171: Tires-General Information
WARNING! Overloading of your tire is dangerous. Overloading can cause tire failure, affect vehicle handling, and increase your stopping distance. Use tires of the recommended load capacity for your vehicle. Never overload them. TIRES—GENERAL INFORMATION Tire Pressure Proper tire inflation pressure is essential to the safe and satisfactory operation of your vehicle.
Page 172: Tire Inflation Pressures
172 STARTING AND OPERATING 2. Economy— Improper inflation pressures can cause uneven wear patterns to develop across the tire tread. These abnormal wear patterns will reduce tread life resulting in a need for earlier tire replacement. Underinflation also increases tire rolling resistance and results in higher fuel consumption.
Page 173 The pressure should be checked and adjusted as well as inspecting for signs of tire wear or visible damage at least once a month. Use a good quality pocket-type gauge to check tire pressure. Do not make a visual judgement when determining proper inflation.
Page 174 174 STARTING AND OPERATING Tire pressure may increase from 2 to 6 psi (13 to 40 kPa) during operation. DO NOT reduce this normal pressure build up or your tire pressure will be too low. Tire Pressures for High Speed Operation The manufacturer advocates driving at safe speeds within posted speed limits.
Page 175: Radial-Ply Tires
Radial-Ply Tires WARNING! Combining radial ply tires with other types of tires on your vehicle will cause your vehicle to handle poorly. The instability could cause an accident. Al- ways use radial ply tires in sets of four (or 6, in case of trucks with dual rear wheels).
Page 176: Tire Spinning
176 STARTING AND OPERATING Do not install a wheel cover or attempt to mount a conventional tire on the compact spare wheel, since the wheel is designed specifically for the compact spare. Do not install more than one compact spare tire/wheel on the vehicle at any given time.
Page 177: Tread Wear Indicators
Tread Wear Indicators Tread wear indicators are in the original equipment tires to help you in determining when your tires should be replaced. These indicators are molded into the bottom of the tread grooves and will appear as bands when the tread depth becomes 1/16 inch (2 mm).
Page 178: Alignment And Balance
178 STARTING AND OPERATING WARNING! • Do not use a tire, wheel size or rating other than that specified for your vehicle. Some combina- tions of unapproved tires and wheels may change suspension dimensions and performance charac- teristics, resulting in changes to steering, han- dling, and braking of your vehicle.
Page 179: Supplemental Tire Pressure Information
Improper alignment will not cause vehicle vibration. Vibration may be a result of tire and wheel out-of- balance. Proper balancing will reduce vibration and avoid tire cupping and spotty wear. SUPPLEMENTAL TIRE PRESSURE INFORMATION A light load vehicle condition is defined as two passen- gers {150 lbs (68 kg) each} plus 200 lbs (91kg) of cargo.
Page 180: Snow Tires
180 STARTING AND OPERATING These cautions apply to all chain traction devices, includ- ing link and cable (radial) chains. Tire chain use is permitted only on the rear tires of SRT–10 Models. NOTE: The use of class “S” chains is permitted on SRT– 10 Models with the use of 17 x 8 steel wheels (part number 52113265AC) available from your authorized dealer.
Page 181: Tire Rotation Recommendations
TIRE ROTATION RECOMMENDATIONS Tires on the front and rear axles of vehicles operate at different loads and perform different steering, driving, and braking functions. For these reasons, they wear at unequal rates, and develop irregular wear patterns. These effects can be reduced by timely rotation of tires. The benefits of rotation are especially worthwhile with aggressive tread designs such as those on On/Off Road type tires.
Page 182: Fuel Requirements
If you experience these symptoms, try another brand of “regular” gasoline be- fore considering service for the vehicle. Over 40 automobile manufacturers around the world have issued and endorsed consistent gasoline specifica- tions (the World Wide Fuel Charter, WWFC) to define fuel properties necessary to deliver enhanced emissions, engine performance, and durability for your vehicle.
Page 183: Gasoline/Oxygenate Blends
Gasoline/Oxygenate Blends Some fuel suppliers blend unleaded gasoline with mate- rials called oxygenates such as 10% alcohol, MTBE, ETBE or TAME. Oxygenates are required in some areas of the country during the winter months to reduce carbon monoxide emissions. Fuels blended with these oxygen- ates may be used in your vehicle.
Page 184: Sulfur In Gasoline
184 STARTING AND OPERATING Sulfur In Gasoline Your vehicle may have been designed to meet California low emission standards on clean burning, low sulfur, California gasoline. Gasoline sold outside of California is allowed to have higher sulfur levels that may affect the performance of your vehicle’s catalytic converter.
Page 185: Carbon Monoxide Warnings
overheat. If you notice a pungent burning odor or some light smoke, your engine may be out of tune or malfunctioning and may require immediate service. Contact your dealer for service assistance. • When pulling a heavy load or driving a fully loaded vehicle when the humidity is low and the temperature is high, use a premium unleaded fuel to help prevent spark knock.
Page 186: Adding Fuel
186 STARTING AND OPERATING the vehicle is raised. Have any abnormal conditions repaired promptly. Until repaired, drive with all side windows fully open. ADDING FUEL NOTE: The fuel tank filler tube is about 2 inches (50 mm) down from the opening. If fuel is poured from a portable container, the container should have a flexible nozzle long enough to extend into the fuel filler tube.
Page 187 CAUTION! Damage to the fuel system or emission control system could result from using an improper fuel tank filler tube cap (gas cap). A poorly fitting cap could let impurities into the fuel system. STARTING AND OPERATING 187 WARNING! • Remove the fuel tank filler tube cap (gas cap) slowly to prevent fuel spray from the filler neck which may cause injury.
Page 188: Catalytic Converter
188 STARTING AND OPERATING CATALYTIC CONVERTER The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic converter will not require maintenance. However, you must keep the en- gine maintained to assure proper operation and prevent possible damage.
Page 189: Vehicle Loading
As with any vehicle, do not park or operate this vehicle in areas where combustible materials such as grass or leaves can come in contact with a hot exhaust system. A scorching odor may be detected if you continue to run a malfunctioning engine.
Page 190 190 STARTING AND OPERATING The label also specifies maximum capacities of front and rear axle systems (GAWR). Total load must be limited so GVWR and front and rear GAWR are not exceeded. Payload The payload of a vehicle is defined as the allowable load weight a truck can carry, including the weight of the driver, all passengers, options and cargo.
Page 191 Loading The actual total weight and the weight of the front and rear of your vehicle at the ground can best be determined by weighing it when it is loaded and ready for operation. The entire vehicle should first be weighed on a commer- cial scale to insure that the GVWR has not been exceeded.
Page 192: Trailer Towing
Gross Vehicle Weight Rating (GVWR) 6500 LBS. TRAILER TOWING DO NOT tow a trailer with Dodge SRT-10 models. SNOWPLOW Dodge SRT-10 Models NOTE: DO NOT use Dodge SRT- 10 Models for snowplow applications.
Page 193: Traction
CAUTION! Using this vehicle for snowplow applications can cause damage to the vehicle. WARNING! Attaching a snowplow to this vehicle could ad- versely affect performance of the airbag system in an accident. Do not expect that the airbag will perform as described earlier in this manual STARTING AND OPERATING 193 TRACTION...
Page 194: Equipment Identification Plate
194 STARTING AND OPERATING EQUIPMENT IDENTIFICATION PLATE The equipment Identification Plate is located on the hood inner surface. The following information about your vehicle is dis- played on this plate: Model, Wheelbase, Vehicle Identifi- cation Number, Truck Order Number, and code numbers with descriptions of all production and special equip- ment on the truck as shipped from the factory.
Page 195 WHAT TO DO IN EMERGENCIES CONTENTS Hazard Warning Lights ....196 Adding Fuel ......197 Jack Location .
Page 196: 196 What To Do In Emergencies
196 WHAT TO DO IN EMERGENCIES HAZARD WARNING LIGHTS The Hazard Warning switch is mounted on the top of the steering column as shown in the illustration. To engage the Hazard Warning lights, depress the button on the top of the steering column. When the Hazard Warning switch is activated, all directional turn signals will flash off and on to warn oncoming traffic of an emergency.
Page 197: Adding Fuel
ADDING FUEL The fuel tank filler tube has a restriction about 2 inches (50 mm) inside the opening. If using a portable fuel container, it should have a flexible nozzle long enough to reach past the restriction. WARNING! A fire may result if gasoline is pumped into a portable container that is in a vehicle or on a truck bed.
Page 198: Jack Location
198 WHAT TO DO IN EMERGENCIES JACK LOCATION Removal The jack and jack tools are stored under the front passen- ger seat. Lift the flap on the side of the seat for access. Remove the jack and tools by removing the wing bolt and sliding the assembly from under the seat.
Page 199: Reinstalling The Scissors-Type Jack And Tools (Srt-10 Models)
Reinstalling The Scissors-Type Jack And Tools (SRT–10 Models) 1. Lower the jack all the way down by turning the jack turn-screw until the jack is snug. 2. Position the jack and tool bag (unrolled). Make sure the lug wrench is under the jack near the jack turn-screw. Turn Screw and Lug WHAT TO DO IN EMERGENCIES 199 3.
Page 200 200 WHAT TO DO IN EMERGENCIES Jack and Tools Tied Tying Bag to Jack with Straps...
Page 201: Changing A Flat Tire
4. Place the jack and tools in the storage position holding the jack by the jack turn-screw, slip the jack and tools under seat so that the bottom slot engages into the fastener on the floor and then secure to the floor pan using the wing bolt.
Page 202: Tire Changing Procedure
202 WHAT TO DO IN EMERGENCIES It is recommended that you stow the flat or spare to avoid tangling the loose cable. NOTE: The winch mechanism is designed for use with the jack extension tube only. Use of an air wrench or other power tools is not recommended and can damage the winch.
Page 203 WARNING! Do not attempt to change a tire on the side of the vehicle close to moving traffic. Pull far enough off the road to avoid the danger of being hit when operating the jack or changing the wheel. • Turn on the Hazard Warning Flasher. •...
Page 204 204 WHAT TO DO IN EMERGENCIES 1. Remove the spare wheel, jack, and tools from storage. 2. Using the wheel wrench, loosen, but do not remove, the wheel nuts by turning them counterclockwise one turn while the wheel is still on the ground. 3.
Page 205 • Operate the jack using the jack drive tube and the wheel wrench. The tube extension, may be used, but is not required. • When changing a rear wheel, assemble the jack drive tube to the jack and connect the drive tube to the extension tube.
Page 206 206 WHAT TO DO IN EMERGENCIES 6. Using the wheel wrench, finish tightening the nuts using a crisscross pattern. Correct nut tightness is 90–110 ft. lbs. (125–150 N·m). If in doubt about the correct tightness, have them checked with a torque wrench by your dealer or at a service station.
Page 207: Hoisting
Disc Type Nut Stud Size Torque Wheels Ft. Lbs. Cone 1/2-20 90-110 To Stow The Flat Or Spare Turn the wheel so that the valve stem is down. Slide the wheel retainer through the center of the wheel and position it properly across the wheel opening. For convenience in checking the spare tire inflation, stow with the valve stem toward the rear of the vehicle.
Page 208: Jump-Starting
208 WHAT TO DO IN EMERGENCIES JUMP-STARTING You should not try to start your vehicle by pushing or towing. Pushing or towing a vehicle equipped with a manual transmission may overheat and damage the catalytic converter. Also, there is a greater risk of an accident when a vehicle is being pushed or towed.
Page 209 Check the Battery Test Indicator (If Equipped). If a yellow or bright colored dot is visible in the indicator (if equipped), DO NOT jump-start the battery. If the indicator (if equipped) is dark or shows a green dot, proceed as follows: 1.
Page 210 210 WHAT TO DO IN EMERGENCIES 5. Connect the other cable, first to the negative terminal of the booster battery and then to the engine of the vehicle with the discharged battery. Make sure you have a good contact on the engine. WARNING! •...
Page 211: Freeing A Stuck Vehicle
WARNING! Any procedure other than above could result in: 1. Personal injury caused by electrolyte squirting out the battery vent; 2. Personal injury or property damage due to battery explosion; 3. Damage to charging system of booster vehicle or of immobilized vehicle. WHAT TO DO IN EMERGENCIES 211 FREEING A STUCK VEHICLE If vehicle becomes stuck in snow, sand, or mud, it can...
Page 212: Towing A Disabled Vehicle
212 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE Proper towing or lifting equipment is required to prevent damage to your vehicle. Use only tow bars and other equipment designed for the purpose, following equip- ment manufacturer’s instructions. Use of safety chains is mandatory.
Page 213 MAINTAINING YOUR VEHICLE CONTENTS Engine Compartment— 8.3L ....216 Onboard Diagnostic System (OBD II) ..217 Emissions Inspection And Maintenance Programs .
Page 214 214 MAINTAINING YOUR VEHICLE Front Suspension Ball Joints ....231 Steering Linkage — Inspection ... . 231 Body Lubrication .
Page 215 Fog Lights ......257 Fluid Capacities ......258 Recommended Fluids, Lubricants And Genuine Parts .
Page 216: 216 Maintaining Your Vehicle
216 MAINTAINING YOUR VEHICLE ENGINE COMPARTMENT— 8.3L...
Page 217: Onboard Diagnostic System (Obd Ii)
ONBOARD DIAGNOSTIC SYSTEM (OBD II) Your vehicle is equipped with a sophisticated onboard diagnostic system called OBD II. This system monitors the performance of the emissions and engine control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as engine emissions well within current government regulations.
Page 218 218 MAINTAINING YOUR VEHICLE For states which have an I/M (Inspection and Maintenance) requirement, this check verifies the following: the MIL (Malfunction Indicator Lamp) is functioning and is not on when the engine is running, and that the OBD (On Board Diagnostic) system is ready for testing.
Page 219: Dealer Service
b. The MIL light will remain fully illuminated until the first engine crank or the key is turned off. This means that your vehicle’s OBD system is ready and you can proceed to the I/M station. If your OBD system is not ready, you should see your dealer or repair facility.
Page 220: Replacement Parts
220 MAINTAINING YOUR VEHICLE WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the proper equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
Page 221 Checking the oil while the vehicle is on level ground will improve the accuracy of the oil level readings. Maintain the oil level between the ADD and SAFE markings on the dipstick. Adding one quart of oil when the reading is at the ADD mark will result in a SAFE reading on these engines.
Page 222: Maintenance Schedules
222 MAINTAINING YOUR VEHICLE • More than 50% of your driving is at sustained high speeds during hot weather, above 32°C (90°F) • Taxi, Police or delivery service (commercial service) • Off-road or desert operation • If equipped for and operating with E-85 (ethanol) fuel.
Page 223 Engine Oil Identification (API) Symbol There is a symbol to aid you in selecting the proper engine oil. This symbol means that the oil has been certified by the American Petroleum Institute (API). We only recommend synthetic API Certified engine oils, such as Mo- bil 1 , that meet the requirements of Material Standard MS-10725.
Page 224: Engine Oil Filter
224 MAINTAINING YOUR VEHICLE Materials Added to Engine Oil Do not add any materials (other than leak detection dyes) to engine oil. Engine oil is an engineered product and it’s performance may be impaired by supplemental addi- tives. Disposing of Used Engine Oil And Oil Filters Care should be taken in disposing of used engine oil and oil filters from your vehicle.
Page 225: Spark Plugs
Spark Plugs Spark plugs must fire properly to assure engine perfor- mance and emission control. New plugs should be in- stalled at the specified mileage. The entire set should be replaced if there is any malfunction due to a faulty spark plug, malfunctioning spark plugs can damage the cata- lytic converter.
Page 226: Catalytic Converter
226 MAINTAINING YOUR VEHICLE Catalytic Converter The catalytic converter requires the use of unleaded fuel only. Leaded gasoline will destroy the effectiveness of the catalyst as an emission control device. Under normal operating conditions, the catalytic con- verter will not require maintenance. However, it is im- portant to keep the engine properly tuned to assure proper catalyst operation and prevent possible catalyst damage.
Page 227: Crankcase Emission Control System
WARNING! A hot exhaust system can start a fire if you park over materials that can burn. Such materials might be grass or leaves coming into contact with your ex- haust system. Do not park or operate your vehicle in areas where your exhaust system can contact any- thing that can burn.
Page 228: Maintenance Free Battery
228 MAINTAINING YOUR VEHICLE Check the ventilation hose for indication of damage or plugging deposits. Replace if necessary. Maintenance Free Battery The top of the maintenance free battery is permanently sealed. You will never have to add water, nor is periodic maintenance required.
Page 229: Air Conditioner
WARNING! Battery fluid is a corrosive acid solution and can burn or even blind you. Don’t allow battery fluid to contact your eyes, skin or clothing. Don’t lean over a battery when attaching clamps. If acid splashes in eyes or on skin, flush the area immediately with large amounts of water.
Page 230: Power Steering - Fluid Check
230 MAINTAINING YOUR VEHICLE WARNING! • Use only refrigerants approved by the manufac- turer for your air conditioning system. Some un- approved refrigerants are flammable and can ex- plode, injuring you. Other refrigerants can cause the system to fail, requiring costly repairs.
Page 231: Front Suspension Ball Joints
WARNING! Fluid level should be checked on a level surface and with the engine off to prevent injury from moving parts and to insure accurate fluid level reading. Do not overfill. Use only manufacturers recommended power steering fluid. If necessary, add fluid to restore to the proper indicated level.
Page 232: Body Lubrication
232 MAINTAINING YOUR VEHICLE Body Lubrication Locks and all body pivot points, including such items as seat tracks, doors, tailgate and hood hinges, should be lubricated periodically to assure quiet, easy operation and to protect against rust and wear. Prior to the appli- cation of any lubricant, the parts concerned should be wiped clean to remove dust and grit;...
Page 233: Exhaust System
To prevent freeze-up of your windshield washer system in cold weather, select a solution or mixture that meets or exceeds the temperature range of your climate. This rating information can be found on most washer fluid containers. WARNING! Commercially available windshield washer solvents are flammable.
Page 234: Cooling System
234 MAINTAINING YOUR VEHICLE WARNING! Exhaust gases can injure or kill. They contain carbon monoxide (CO) which is colorless and odorless. Breathing it can make you unconscious and can eventually poison you. To avoid breathing CO, fol- low the preceding safety tips. Exhaust System Rubber Isolator and Loop-Type Hanger —...
Page 235 Check the coolant reserve tank tube for condition and tightness or connections at the reserve tank and radiator. Check the coolant pressure cap and coolant reserve system for proper vacuum sealing. With the engine at normal operating temperature, note the level of the coolant in the coolant reserve tank.
Page 236 236 MAINTAINING YOUR VEHICLE Adding Coolant When adding coolant or refilling system, a 50% solution of ethylene glycol antifreeze coolant in water should be used. Higher concentrations (not to exceed 65%) are required if temperatures below -34 F° (-37 C°) are antici- pated.
Page 237 CAUTION! Mixing of coolants other than specified (non- HOAT), may result in engine damage that may not be covered under the new vehicle warranty, and decreased corrosion protection. If a non-HOAT cool- ant is introduced into the cooling system in an emergency, it should be replaced with the specified coolant as soon as possible.
Page 238: Hoses And Vacuum/Vapor Harnesses
238 MAINTAINING YOUR VEHICLE WARNING! The warning words “DO NOT OPEN HOT” on the radiator pressure cap are a safety precaution. Heat causes pressure to build up in the cooling system. To prevent scalding or injury, do not remove the pres- sure cap.
Page 239 The brake master cylinder has a translucent plastic reservoir. On the outboard side of the reservoir, there is a “MAX” dot and an “MIN” dot. The fluid level must be kept within these two dots. Do not add fluid above the MAX mark, because leakage may occur at the cap.
Page 240: Clutch Hydraulic System
240 MAINTAINING YOUR VEHICLE Brake Hoses Inspection should be performed whenever the brake system is serviced or at intervals specified. Inspect hy- draulic brake hoses for surface cracking, scuffing or worn spots. If there is any evidence of cracking, scuffing, or worn spots, the hose should be replaced immediately! Eventual deterioration of the hose can take place with possible burst failure.
Page 241: Transmission
Drain and Refill Vehicles operated in normal service do not have regularly scheduled oil changes. If fluid has become contaminated with water or to provide the correct viscosity grade, drain and refill. Lubricant Selection Refer to Recommended Fluids, Lubricants and Genuine Parts for correct fluid type.
Page 242: Front Wheel Bearings
Schedule B. If contaminated with water, the fluid should be changed immediately. Front Wheel Bearings Front wheel bearings for all Dodge Ram Trucks are sealed-for-life. They do not require greasing or seal replacement. In some instances, these bearings will “purge” excess grease and the bearing will look slightly wet.
Page 243: Appearance Care And Protection From Corrosion
quality level available and when combined as shown can be used for both wheel bearing and chassis lubrication. Use only those greases that have the NLGI symbol on the container along with the proper quality level for your application. Appearance Care and Protection from Corrosion Protection of Body and Paint from Corrosion Vehicle body care requirements vary according to geo- graphic locations and usage.
Page 244 244 MAINTAINING YOUR VEHICLE Washing • Wash your vehicle regularly. Always wash your ve- hicle in the shade using a mild car wash soap, and rinse the panels completely with clear water. • If insects, tar or other similar deposits have accumu- lated on your vehicle, wash it as soon as possible.
Page 245 • If your vehicle is damaged due to an accident or similar cause which destroys the paint and protective coating have your vehicle repaired as soon as possible. The cost of such repairs is considered the responsibil- ity of the owner. •...
Page 246 246 MAINTAINING YOUR VEHICLE and Mopar Total Clean. Care should be taken to avoid soaking your leather upholstery with any liquid. Please do not use polishes, oils, cleaning fluids, solvents, deter- gents, or ammonia based cleaners to clean your leather upholstery.
Page 247: Fuse And Relay Center
Seat Belt Maintenance Do not bleach, dye or clean the belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage will also weaken the fabric. If the belts need cleaning, use a mild soap solution or lukewarm water.
Page 248: Vehicle Storage
248 MAINTAINING YOUR VEHICLE 2. Use specified fuses only. 3. Always properly reinstall the cover. VEHICLE STORAGE If you are storing your vehicle for more than 21 days, we recommend that you take the following steps to mini- mize the drain on your vehicle’s battery: •...
Page 249: Bulb Replacement
BULB REPLACEMENT Headlight (Halogen)/Front Park and Turn Lights CAUTION! This is a halogen bulb. Avoid touching the glass with your fingers. Reduced bulb life will result. 1. Remove the two (2) expanding fasteners from the headlight welt. MAINTAINING YOUR VEHICLE...
Page 250 250 MAINTAINING YOUR VEHICLE 2. Remove the three (3) bolts from the headlight housing. NOTE: The lower bolt on the driver side headlight also retains the ambient temperature sensor between the headlight assembly and the frame.
Page 251 MAINTAINING YOUR VEHICLE...
Page 252 252 MAINTAINING YOUR VEHICLE 3. Pull the housing out from the fender to allow room to disconnect the electrical connectors. 4. Unlock and pull connector straight from the base of the headlight halogen bulb. 5. Twist connector on turn signal/park light bulb and remove connector and bulb from housing.
Page 253: Tail, Stop, Turn And Backup Lights
Tail, Stop, Turn and Backup Lights 1. Remove the two (2) screws that pass through the bed sheetmetal. MAINTAINING YOUR VEHICLE 2. Pull the housing straight out from the body, with a quick motion, to separate the housing from the body. If not pulled straight, locators may be damaged.
Page 254 254 MAINTAINING YOUR VEHICLE 4. Remove the four (4) screws from the bulb strip in the housing. 5. Pull the appropriate bulb straight from the bulb strip. • Top Bulb: Park/Turn/Hazard • Center Bulb: Stop/Park/Sidemarker • Bottom Bulb: Backup Lights...
Page 255: Center High-Mounted Stoplight With Cargo Light
6. Reverse procedure for installation of bulbs and hous- ing. 7. While holding the taillight firmly in place, fasten the top screw first. MAINTAINING YOUR VEHICLE Center High-Mounted Stoplight With Cargo Light 1. Remove the two (2) screws holding the housing/lens to the body as shown.
Page 256 256 MAINTAINING YOUR VEHICLE 2. Separate the connector holding the housing and wir- ing harness to the body. 3. Turn desired bulb socket ⁄ turn and remove socket and bulb from housing. 4. Pull desired bulb straight from the socket. •...
Page 257 Fog Lights 1. Reach under the vehicle, unlock and twist connector counterclockwise ⁄ turn and remove connector and bulb from housing. MAINTAINING YOUR VEHICLE 2. Pull bulb straight from the connector. 3. Reverse procedure for installation of bulbs and hous- ing.
Page 258 258 MAINTAINING YOUR VEHICLE FLUID CAPACITIES Fuel SRT-10 Models Engine Oil (with filter) 8.3L Cooling System 8.3L U.S. Metric 26 gal. 8.5 qts. 8.0L 20 qts.
Page 259 RECOMMENDED FLUIDS, LUBRICANTS AND GENUINE PARTS Engine Component Fluids, Lubricants and Genuine Parts Engine Coolant Mopar Antifreeze/Coolant 5 Year/102,000 Mile Formula HOAT (Hybrid Or- ganic Additive Technology) P/N 05066386AA or equivalent. Engine Oil We only recommend synthetic engine oils, such as Mobil 1 , that are API Certified and meet the requirements of Material Standard MS-10725.
Page 260 260 MAINTAINING YOUR VEHICLE Chassis Component Transmission Fluid Clutch Linkage Limited-Slip Rear Axle Brake Master Cylinder Power Steering Reservoir Fluids, Lubricants and Genuine Parts. Mopar Synthetic Manual Transmission Lubricant 75W/85W (Castrol Syn- torq LT 75W/85W) Multipurpose Grease, NLGI Grade 2 E.P. Mopar SAE 90W.
Page 261 MAINTENANCE SCHEDULES CONTENTS Emission Control System Maintenance ..262 Maintenance Schedules ....262 Schedule “B” ......265 Schedule “A”...
Page 262: Emission Control System Maintenance
262 MAINTENANCE SCHEDULES EMISSION CONTROL SYSTEM MAINTENANCE The “Scheduled” maintenance services, listed in bold type in this section (Section 8) must be done at the times or mileages specified to assure the continued proper functioning of the emission control system. These, and all other maintenance services included in this manual, should be done to provide best vehicle performance and reliability.
Page 263 • Off-road or desert operation. • If equipped for and operating with E-85 (ethanol) fuel. NOTE: If ANY of these apply to you then change your engine oil every 3,000 miles (5 000 km) or 3 months, whichever comes first and follow schedule “B” of the Maintenance Schedules section of this manual.
Page 264 264 MAINTENANCE SCHEDULES At Each Stop for Fuel • Check the engine oil level about 5 minutes after a fully warmed engine is shut off. Checking the oil level while the vehicle is on level ground will improve the accu- racy of the oil level reading.
Page 265: Schedule "B
Schedule “B” Follow schedule “B” if you usually operate your vehicle under one or more of the following conditions. • Day or night temperatures are below 32° F (0° C). • Stop and go driving. • Extensive engine idling. • Driving in dusty conditions. •...
Page 266 266 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 3,000 6,000 9,000 (5 000) (10 000) (14 000) 12,000 15,000 (19 000) (24 000)
Page 267 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect and replace, if necessary, the PCV orifice. 18,000 21,000 24,000 (29 000) (34 000) (38 000) SCHEDULE “B”...
Page 268 268 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. 33,000 36,000 39,000 (53 000) (58 000) (62 000) 42,000 45,000 (67 000) (72 000)
Page 269 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Replace ignition cables. Inspect and replace, if necessary, the PCV orifice. 48,000 51,000 54,000 (77 000)
Page 270 270 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Inspect engine air cleaner filter. Change rear axle fluid. Inspect brake linings. Inspect auto tension drive belt and replace if re- quired. 63,000 66,000 69,000 (101 000) (106 000) (110 000) 72,000 75,000...
Page 271 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if neces- sary. Replace spark plugs. Inspect PCV valve, replace as necessary. Inspect auto tension drive belt and replace if re- quired.
Page 272 272 SCHEDULE “B” Miles (Kilometers) Change engine oil and engine oil filter. Flush and replace engine coolant. Flush and replace Power Steering Fluid. Inspect brake linings. 93,000 96,000 99,000 (149 000) (154 000) (158 000) 100,000 102,000 (160 000) (163 000)
Page 273 Miles (Kilometers) Change engine oil and engine oil filter. Change rear axle fluid. Inspect brake linings. Inspect engine air cleaner filter, replace if necessary. Replace spark plugs. Replace ignition cables. Inspect and replace, if necessary, the PCV orifice. Inspect auto tension drive belt and replace if required.
Page 274: 274 Schedule "A
274 SCHEDULE “A” Schedule “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. 6,000 12,000 18,000 (10 000) (19 000) (29 000) [12] [18] 24,000 30,000 (38 000) (48 000) [24] [30]...
Page 275 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Flush and replace engine coolant at 60 months, regardless of mileage. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect and replace, if necessary, the PCV orifice. Replace ignition cables.
Page 276 276 SCHEDULE “A” Miles (Kilometers) [Months] Change engine oil and engine oil filter. Flush and replace Power Steering Fluid. Inspect brake linings. Replace engine air cleaner filter. Replace spark plugs. Inspect and replace, if necessary, the PCV orifice. Inspect auto tension drive belt and replace if required.
Page 277 Miles (Kilometers) [Months] Change engine oil and engine oil filter. Flush and replace engine coolant, if not done at 60 mos. Inspect brake linings. Inspect auto tension drive belt and replace if required. Replace ignition cables. Replace engine air cleaner filter. Replace spark plugs.
Page 278 278 SCHEDULE “A” WARNING! You can be badly injured working on or around a motor vehicle. Do only that service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent me- chanic.
Page 279: If You Need Consumer Assistance
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Vehicle ......280 Prepare For The Appointment .
Page 280: Suggestions For Obtaining Service For Your Vehicle
280 IF YOU NEED CONSUMER ASSISTANCE SUGGESTIONS FOR OBTAINING SERVICE FOR YOUR VEHICLE Prepare For The Appointment If you’re having warranty work done, be sure to have the right papers with you. Take your warranty folder. All work to be performed may not be covered by the warranty, discuss additional charges with the service manager.
Page 281 The manufacturer has empowered its dealers to make warranty and repair decisions that ensure you are not inconvenienced. There is no need for you to wait for a decision from the manufacturer. If a special circumstance occurs that requires information from the manufacturer, we have asked the dealer’s service management to make the contact on your behalf.
Page 282 282 IF YOU NEED CONSUMER ASSISTANCE DaimlerChrysler Canada Inc. Customer Center P.O. Box 1621 Windsor, Ontario N9A 4H6 Phone —(800) 465–2001 In Mexico contact: Av. Prolongacion Paseo de la Reforma, 1240 Sante Fe C.P. 05109 Mexico, D. F. In Mexico (915) 729–1248 or 729–1240 Outside Mexico (525) 729–1248 or 729–1240 Customer Assistance For The Hearing Or Speech Impaired (TDD/TTY)
Page 283: Warranty Information
The manufacturer will not stand behind any service contract that is not the manufacturer’s Service Contract. It is not responsible for any service contract other than the manufacturer’s Service Contract. If you purchased a service contract that is not a manufacturer’s Service Contract, and you require service after your manufactur- er’s new vehicle limited warranty expires, please refer to your contract documents, and contact the person listed in...
Page 284 284 IF YOU NEED CONSUMER ASSISTANCE...
Page 285: Mopar Parts
MOPAR PARTS Mopar fluids, lubricants, parts, and accessories are available from your dealer. They will help you keep your vehicle operating at its best. REPORTING SAFETY DEFECTS In the 50 United States and Washington D.C.: If you believe that your vehicle has a defect which could cause a crash or cause injury or death, you should immediately inform the National Highway Traffic Safety Administra- tion (NHTSA) in addition to notifying the manufacturer.
Page 286: Publication Order Forms
286 IF YOU NEED CONSUMER ASSISTANCE PUBLICATION ORDER FORMS To order the following manuals, you may use either the website or the phone numbers listed below. Visa, Mas- tercard, American Express, and Discover orders are ac- cepted. If you prefer mailing your payment, please call for an order form.
Page 287 IF YOU NEED CONSUMER ASSISTANCE 287 Call Toll Free at 1–800–890–4038 (U.S.) or 1–800–387–1143 (Canada) Visit us on the World Wide Web at: www.techauthority.daimlerchrysler.com or www.daimlerchrysler.ca/manuals...
Page 289 INDEX...
Page 290 290 INDEX Adding Fuel ......186,197 Additives, Fuel ......184 Air Cleaner, Engine .
Page 291 Hoses ......240 Master Cylinder ..... . . 238 Parking .
Page 292 292 INDEX Compass Calibration ..... 103 Compass Variance ..... . . 104 Computer, Trip/Travel .
Page 293 Emergency, In Case of Freeing Vehicle When Stuck ....211 Hazard Warning Flasher ....196 Jacking .
Page 294 294 INDEX Fog Lights ......89,257 Four-Way Hazard Flasher ....196 Freeing A Stuck Vehicle .
Page 295 Hoisting ......207 Homelink Transmitter ....106 Hood Release .
Page 296 296 INDEX Courtesy/Reading ..... . 99 Cruise ......127 Daytime Running .
Page 297 Schedule B ......265 Malfunction Indicator Light ....218 Manual, Service .
Page 298 298 INDEX Passing Light ......91 PCV Valve ......227 Pedals, Adjustable .
Page 299 Safety Checks Inside Vehicle ....60 Safety Checks Outside Vehicle ....60 Safety Defects, Reporting .
Page 300 300 INDEX Spark Plugs ......225 Speed Control ......96 Speedometer .
Page 301 Jacking ......202 Load Capacity ..... 167,168 Radial .
Page 302 302 INDEX Warning Lights (Instrument Cluster Description) Warnings and Cautions ..... 5 Warranty Information ..... 283 Washers, Windshield .

This manual is also suitable for:

Dr srt-10 2004

Dodge 2004 DR Ram SRT-10 Owner's Manual

Table of Contents

Things to Know before Starting Your Vehicle

Understanding the Features of Your Vehicle

Understanding Your Instrument Panel

Starting and Operating

What to Do in Emergencies

Maintaining Your Vehicle

216 Maintaining Your Vehicle

8 Maintenance Schedules

Maintenance Schedules

Quick Links

INTRODUCTION

TABLE OF CONTENTS

Chapters

Related Manuals for Dodge 2004 DR Ram SRT-10

Summary of Contents for Dodge 2004 DR Ram SRT-10