Hauppauge WINTV-HVR-4000 CYBERLINK QI Quick Installation Manual

WinTV-HVR-4000
Quick Installation Guide for Windows XP
© 2006 Hauppauge Computer Works · QI-WNTV-HVR4000CYBER-V1.0-ENG · 2006/10/26
Hauppauge Computer Works, Ltd. Tech Support: (+44) 0207 378 0202
Telephone: (+44) 0207 378 1997
10 Borough High Street
Bank Chambers Fax: (+44) 0207 357 9171
London, UK, SE1 9QQ
www.hauppauge.co.uk
Hauppauge Computer Works, Inc. Tech Support: (+1) 631 434 3197
Telephone: (+1) 631 434 1600
91 Cabot Court
Hauppauge, NY 11788 Fax: (+1) 631 434 3198
www.hauppauge.com
Hauppauge Digital Asia, Pte. Ltd. Tech Support: (+65) 276 4412
Blk 1093, Lower Delta Road #04-05 Telephone: (+65) 276 9163
Tiong Bahru Industrial Estate Fax: (+65) 276 9167
Singapore 169204
www.hauppauge.com.sg
1. Contents of the WinTV-HVR-package
● WinTV-HVR-4000 - PCI-board
● Remote control transmitter with
2 AAA batteries
● Remote control receiver
with velcro dot fastener
● FM Radio antenna
● S-Video/Composite Adapter
● Installation CD-ROM with:
· CyberLink PowerCinema 4.7
2. Installing the WinTV-HVR board
To install, switch off the computer and remove the computer cover.
The manufacturer of your PC supplies instructions on removing the PC
cover.
N ote: Your PC could be damaged by electrostatic discharge.
Avoid this by contacting the earthed chassis of your PC,
before you open it or touch the PCI card.
● Locate a free PCI slot (a short white slot). Unscrew and remove the
meta cover plate which covers the back of the empty slot.
●
Plug the WinTV-HVR board into the PCI slot, and screw the WinTV-
HVR metal cover plate to the PC.
3. Connections of the WinTV-HVR-4000 board
With the HVR you can watch and record analog TV, DVB-Terrestrial and
DVB-Satellite channels. You can also connect sources via the compos-
ite and S-Video inputs and listen to FM Radio as well.
You can now connect the leads provided to the WinTV-HVR-4000 in
the following order.
FM FM Radio-Antenna
TV TV-Antenna
SAT SAT-Cable from the LNB of your satellite dish
S-VIDEO IN S-Video-Input *
LINE IN Stereo-Audio-Input, from the output of your source
IR Input for the Infra-red-Sensor
N ote: for using a RCA Yellow Phono composite input you
must use the supplied S-Video to composite adapter.
Page 1
4. WinTV-HVR-4000 DVB reception advice
DVB-T
Please ensure that you have a suitable TV aerial connected to the
WinTV card. You should then ensure you are located in a area that
supports Digital Terrestrial TV by visiting:
www.dtg.org.uk/retailer/coverage.html and entering your post code.
If your area does have digital Terrestrial TV coverage, please check
your TV antenna as most antenna's that are over 8 years old may not
support the Digital Terrestrial TV broadcasts and you may need to
update yours to a 'Wideband or Highgain' antenna.
DVB-S
Please ensure that your satellite dish is correctly aligned and the Sat
cable is connectly directly from the LNB and not via a set top box.
5. Install the WinTV-HVR Windows XP driver
N ote: You may need to disable your antivirus programs during
the installation only.
Start your PC. When it is com-
pletely booted, the Add New
Hardware Wizard will appear.
Insert the Hauppauge Installation
CD-ROM into your CD-ROM
drive. Click Next.
Select Search for the best driver
for your device (Recommended).
Click Next.
N ote: If you see a
Hardware Installation
box that mentions that
the driver is not digitally
signed, click the "Continue
Anyway" button to continue
the installation.
Once the driver components are
installed, click the Finish button.
You can check to see if the driver has been installed correctly. Click on
Start / Settings / Control Panel / System / Hardware / Device
Manager.
If you then click on the Sound
Video and Game Controllers sec-
tion you should see the eight
WinTV-HVR components.
If any of them have a yellow
exclamation mark, follow this pro-
cedure:
1. Close Device Manager
2. On the Hauppauge Installation
CD-ROM double click on the file
called "HcwDriverInstall". The
windows "Searching for hard-
ware and updating drivers..."
appears. Click on the bar to exit
and re-start the computer
3. Check again to see if the driver
has been installed correctly. If not, please contact our tech support.
6. CyberLink Software Installation
To start the software installation, click Start / Run then type your CD-
ROM drive letter (for example: D:\) and then Setup.exe.
Click Next.and follow the on
screen instructions to install the
software.
Once the installation is complete,
please re-start your computer.
Page 2
7. CyberLink PowerCinema
To start the PowerCinema application double click on the CyberLink
PowerCinema Icon on your desktop or click on Start / All Programs /
CyberLink PowerCinema / PowerCinema.
The Setup Wizard will appear
which will guide you through the
setup and configuration of the
application, click Next.
Select the type of screen that you
are using (4:3 is normal TV /
Monitor screen size and 16:9 is a
widescreen TV / Monitor) and
click Next.
Select the type of speaker setup
that you are using and click Next.
The WinTV-HVR-4000 has a
Hybrid tuner and can be config-
ured for all 4 types of signals:
Analogue (Cable TV), DVB-T, DVB-
S / HD DVB-S2.
You need to ensure that you have
connected the cables correctly
before performing a channel
scan.
This section will explain how to
scan in analog, digital DVB-T and
digital DVB-S.
You can configure a signal input
by selecting Settings / TV / Signal
settings.
Analog TV Setup
Select if you are using a Cable or
Antenna signal and click Next.
Select the region that you are
located in and click Next.
Page 3
Click on Autoscan for TV
Channels Now to start searching
for TV channels. During the chan-
nel scan the TV pictures will brei-
fly appear.
Once the channel scan is finished
click on Complete.
Digital DVB-T Setup
Select Digital (DVBT) and click
Next.
Select the region that you are
located in and click Next.
Click on Autoscan for TV
Channels Now to start searching
for TV channels. During the chan-
nel scan the TV pictures will brei-
fly appear.
Once the channel scan is finished
click on Complete.
Digital DVB-S/DVB-S2 TV Setup
Select Digital (DVBS) and click
Next.
Page 4