Automatic Input Switching (Auto Function) - Pioneer 507CMX - PDP - 50" Plasma Panel Operating Instructions Manual

Other Operations
Automatic input switching
(AUTO FUNCTION)
This display is equipped with an optional [AUTO
FUNCTION] selector. When enabled, the selector
automatically switches the display's input source to INPUT1
when an image signal is detected at the INPUT1 terminal.
Remote control unit
DISPLAY
STANDBY/ON MENU
/ SET
MENU SET
Main unit operating panel
1
Press the MENU button to display the menu
screen.
M E N U
P I C T U R E S C R E E N
C O N T R A S T
B R I G H T N E S S
H . E N H A N C E
V. E N H A N C E
P I C T U R E R E S E T
SET
ENTER
32
En
MENU
2/3
SET
5/∞
INPUT SCREEN SIZE – VOL +
5/∞ 2/3
I N P U T 1
S E T U P O P T I O N
: 0
: 0
0
:
: 0
MENU
EXIT
2
Use the 2/3 buttons to select [OPTION].
M E N U
P I C T U R E S C R E E N
L A N G U A G E
E N E R G Y S AV E
T I M E R S E T T I N G
S C R E E N M G T.
A U T O S E T U P M O D E
A U T O F U N C T I O N
P I P D E T E C T
S P L I T F R E E Z E
SET ENTER
3 Use the 5/∞ buttons to select [AUTO FUNCTION].
M E N U
P I C T U R E S C R E E N
L A N G U A G E
E N E R G Y S AV E
T I M E R S E T T I N G
S C R E E N M G T.
A U T O S E T U P M O D E
A U T O F U N C T I O N
P I P D E T E C T
S P L I T F R E E Z E
SET CHANGE
4
Press the SET button to select [INPUT1].
The factory default setting is [OFF]. Each time the
SET button is pressed, the selector function switches
alternately as shown:
3 OFF
INPUT1 2
÷ OFF .......... [AUTO FUNCTION] is disabled.
÷ INPUT1 ..... ÷ When a signal is detected at INPUT1,
the input source automatically
switches to [INPUT1].
÷ After the [AUTO FUNCTION] mode
has caused the input to switch, if the
input signal is no longer detected, the
input source reverts to the one
selected before operation of the
[AUTO FUNCTION] mode.
÷ If the input changes when the unit is
in [AUTO FUNCTION] mode, pressing
the INPUT button to select a different
input will cause the [AUTO
FUNCTION] mode to be temporarily
disabled, but it can be enabled again
by turning the power ON/OFF.
5
When finished with the setting, press the MENU
button to return to the normal screen image.
Notes
÷ The [AUTO FUNCTION] for [INPUT1] is supported only when a
separate SYNC or composite SYNC analog RGB signal is input.
(When a G ON SYNC or component video signal is input,
[AUTO FUNCTION] is disabled.)
÷ The [AUTO FUNCTION] setting affects all input sources.
I N P U T 1
S E T U P O P T I O N
: E N G L I S H
: S TA N D A R D
: I N A C T I V E
: O F F
: A C T I V E
: O F F
MENU EXIT
I N P U T 1
S E T U P O P T I O N
: E N G L I S H
: S TA N D A R D
: I N A C T I V E
: O F F
: A C T I V E
: O F F
MENU EXIT