Accessories/ Installation Procedure - Kenwood KDC-BT952HD Instruction Manual

Appendix
81
|
KDC-X996/ KDC-BT952HD
• Sirius, XM and all related marks and logos are
trademarks of Sirius XM Radio Inc. All rights reserved.
• PANDORA, the PANDORA logo, and the Pandora trade
dress are trademarks or registered trademarks of
Pandora Media, Inc., used with permission.
• HD Radio Technology manufactured under license
from iBiquity Digital Corporation. U.S. and Foreign
Patents. HD Radio™ and the HD, HD Radio, and "Arc"
logos are proprietary trademarks of iBiquity Digital
Corp.
• "Adobe Reader" is a trademark of Adobe Systems
Incorporated.
• The "AAC" logo is a trademark of Dolby Laboratories.
• The Bluetooth word mark and logos are owned by
the Bluetooth SIG, Inc. and any use of such marks
by JVC KENWOOD Corporation is under license.
Other trademarks and trade names are those of their
respective owners.
• iTunes is a trademark of Apple Inc.
• "Made for iPod" and "Made for iPhone" mean that an
electronic accessory has been designed to connect
specifically to iPod, or iPhone, respectively, and
has been certified by the developer to meet Apple
performance standards. Apple is not responsible for
the operation of this device or its compliance with
safety and regulatory standards. Please note that the
use of this accessory with iPod, or iPhone may affect
wireless performance.
• iPhone, iPod, iPod classic, iPod nano, and iPod touch
are trademarks of Apple Inc., registered in the U.S. and
other countries.
• Android is a trademark of Google Inc.
• BlackBerry®, RIM®, Research In Motion® and related
trademarks, names and logos are the property of
Research In Motion Limited and are registered and/or
used in the U.S. and countries around the world. Used
under license from Research In Motion Limited.

Accessories/ Installation Procedure

Accessories
1 2
..........1 ..........2
3 4
..........4 ..........4
5
..........1
3 m (9.5 ft)
Installation Procedure
1
To prevent a short circuit, remove the key from the
ignition and disconnect the - battery.
2
Make the proper input and output wire
connections for each unit.
3
Connect the speaker wires of the wiring harness.
4
Connect the wiring harness wires in the following
order: ground, battery, ignition.
5
Connect the wiring harness connector to the unit.
6
Install the unit in your car.
7
Reconnect the - battery.
8
Press the reset button.
2WARNING
If you connect the ignition wire (red) and the battery wire
(yellow) to the car chassis (ground), you may cause a short
circuit, that in turn may start a fire. Always connect those
wires to the power source running through the fuse box.
¤
• Mounting and wiring this product requires skills and
experience. For safety's sake, leave the mounting and wiring
work to professionals.
• Make sure to ground the unit to a negative 12V DC power
supply.
• Do not install the unit in a spot exposed to direct sunlight
or excessive heat or humidity. Also avoid places with too
much dust or the possibility of water splashing.
• Do not use your own screws. Use only the supplied screws.
Using wrong screws, could damage the unit.
• If the power is not turned ON ("Protect" is displayed), the
speaker wire may have a short-circuit or touched the
chassis of the vehicle and the protection function may
have been activated. Therefore, the speaker wire should be
checked.
• If your car's ignition key switch does not have an ACC
position, connect the ignition wires to a power source
that can be turned on and off with the ignition key. If you
connect the ignition wires to a constant-voltage power
source, as with battery wires, the battery may die.
• If the console has a lid, make sure to install the unit so that
the faceplate will not hit the lid when it is closed or opened.
• If the fuse blows, first make sure the wires are not touching
other parts to cause a short circuit, and then replace the old
fuse with one with a new the same rating.
• Insulate unconnected wires with vinyl tape or other similar
materials. To prevent a short circuit, do not remove the caps
on the ends of the unconnected wires and terminals.
• Connect the speaker wires correctly to the corresponding
terminals. The unit may be damaged or fail to work if you
share the - wires or ground them to any metal part in the
car.
• When connecting only two speakers, connect the
connectors either to both of the front output terminals
or to both of the rear output terminals (do not mix front
and rear terminals). For example, if you connect the +
connector of the left speaker to a front output terminal, do
not connect the - connector to a rear output terminal.
• After the installing the unit, check whether the brake lamps,
blinkers, wipers, etc. on the car are working properly.
• Mount the unit so that the mounting angle is 30° or less.
• Reception may become poor if there are
metal objects near the Bluetooth antenna
Bluetooth antenna unit
For Good Reception
To assure good reception, note the following:
• Communicate with the cell-phone within the line-
of-sight distance of 10 m (30 ft). The communication
range becomes shorter depending on the
surrounding environment. The communication
range also becomes shorter when there is an
obstacle between this unit and the cell-phone. The
above maximum communication range (10 m) is
not always assured.
• A broadcast station or walkie-talkie located nearby
can interfere with communication due to a too
strong signal.
|
English
82