Connecting Digital Audio Sources - Pioneer VSX9120TXHK - 770w 7.1 Channel Dolby Truehd Operating Instructions Manual

Connecting your equipment
VSX-9120TXH
MULTI-ZONE & SOURCE ZONE 2
OPTICAL
DIGITAL
IN 1
OUT
IR
OUT
COMPONENT VIDEO
IN 1
Y P
B
IN 2 (DVR/
IN
VCR1)
1
IN 2
(TV/SAT)
IN
2
Y P
OUT IN 3 B
(CD)
RS-232C S-VIDEO
ASSIG-
NABLE
1 3
HDMI
CONTROL iPod
OUT
XM
IN
IN
IN
AUDIO IN OUT IN
L
IN 1
(DVD/LD)
R
IN 2
(DVR/VCR2)
CD CD-R/TAPE/MD
COAXIAL
ASSIGNABLE
1 2
Y
P
B
P
R
2
COMPONENT
VIDEO
Y
P
B
P
R
COMPONENT
1
DVD player
VIDEO
1 Connect the component video outputs of your
source to a set of ASSIGNABLE COMPONENT VIDEO
inputs.
Connect using a three-way component video cable.
• Since they are assignable, it doesn't matter which
component video inputs you use for which source.
After connecting everything, you'll need to assign the
component video inputs—see The Input Setup menu
on page 60.
2 Connect the COMPONENT VIDEO OUT jacks to the
component video inputs on your TV or monitor.
Use a three-way component video cable.
Note
1 • If your digital component only has a coaxial digital output, you can connect it to one of the coaxial inputs on this receiver using a coaxial cable. When
you set up the receiver you'll need to tell the receiver which input you connected the component to (see also The Input Setup menu on page 60).
• The digital outputs from other components can be connected to any spare digital audio inputs on this receiver. You can assign them when setting up
the receiver (see also The Input Setup menu on page 60).
2 In order to record some digital sources, you must make analog connections as explained in Connecting analog audio sources below.
ANTENNA
IN
AM LOOP
P
CENTER
L L
P Y P P
R B R
OUT
IN
3
P Y P P
R B R
R R
SUB
ASSIGNABLE 1 3
FRONT WOOFER
IN IN OUT IN OUT IN MONITOR
OUT
VIDEO
L
IN IN OUT IN OUT IN
R
DVD/LD TV/SAT DVR/VCR1 DVR/VCR2
FRONT
MULTI CH
TV

Connecting digital audio sources

This receiver has both digital inputs and outputs,
allowing you to connect digital audio components for
playback and for making digital recordings.
Most digital components also have analog connections.
See Connecting analog audio sources on the following
page if you want to connect these too.
MULTI-ZONE & SOURCE ZONE 2
OPTICAL
DIGITAL
IN 1
OUT
OUT
COMPONENT VIDEO
IN 1
Y
IN 2 (DVR/
IN
VCR1)
1
IN 2
(TV/SAT)
IN
2
Y
OUT
IN 3
(CD)
RS-232C
ASSIG-
NABLE
1 3
HDMI
CONTROL iPod
OUT
XM
IN
IN
IN
IN OUT
AUDIO
L
IN 1
(DVD/LD)
R
IN 2
(DVR/VCR2)
CD CD-R/TAPE/MD
COAXIAL
ASSIGNABLE
1 2
VSX-9120TXH
1
OPTICAL COAXIAL
DIGITAL OUT
CD-R, MD,
DAT, etc.
1 Connect an optical-type
your digital component to the DIGITAL 3 (CD) input.
Use an optical cable for the connection.
2 For recording equipment, connect the optical-type
DIGITAL output to a digital input on the recorder.
Use an optical cable to connect to the DIGITAL OUT.
ANTENNA
IN
IR
AM L
L
P P Y P P
B R B R
OUT
IN
3
P P Y P P
B R B R
R
ASSIGNABLE 1 3
S-VIDEO
IN IN OUT IN OUT
VIDEO
IN IN IN OUT IN OUT
DVD/LD TV/SAT DVR/VCR1 DVR/
2
OPTICAL
DIGITAL IN
1
digital audio output on
2
03
15
En