Advertisement
reached the limit of your amplifier's or receiver's volume capability
and should quickly reduce the volume to avoid damaging your
speakers and/or your amplifier or receiver.
NOTE: 12 o'clock on most receivers is close to full volume.
9) Adjust the volume of the SSVCs to the desired listening level.
10) To turn Off your speakers, press the function control button once.
The status indicator will turn red and your speakers will be muted
again. You may also turn the volume control knob to the full
counter clockwise position to turn Off the speakers.
SMART SELECT™ SPECIAL FEATURES OPERATION
6
In addition to On and Off control, the function control button can be
used to send system-wide commands to turn all SSVCs On or Off.
To mute all volume controls (All Off feature)
1) On any SSVC, press the function control button until the status
indicator light is red.
2) Press and hold the function control button until the status indicator
blinks amber.
3) All connected SSVCs will now be in mute mode.
To enable all volume controls (All On feature)
1) On any SSVC, press the function control button until the status
indicator light is solid green.
2) Press and hold the function control button until the status indicator
blinks amber.
3) All connected SSVCs will now be in Active mode.
To turn Off Smart Select™ System
1) On any SSVC, press the function control button until the status
indicator light is red.
2) Press and hold the function control button until the status indicator
blinks amber, and then turns red.
3) All connected SSVCs will now be in Mute mode.
4) Press and hold the function control button again until the status
indicator blinks amber.
5) The status indicator will no longer be illuminated.
6) The SSVCs are now in Standby mode and the AC power to the com-
ponents connected to the Smart AC™ Power Controller is turned Off
according to the settings of the Smart AC™ Controller (see Smart
AC™ instruction manual).
To turn On Smart Select™ System
1) On any SSVC, press the function control button once. The status
indicator will light green.
2) The SSVC is now in Active mode. All other SSVCs will be in Mute
mode.
7
SPECIFICATIONS
Audio-
• Power rating/channel:
• 126 Watts power handling
• 14 Watts RMS, continuous
• Uses Ultra-Match™ impedance matching autoformers.
• Accepts up to 12 AWG wire.
• Attenuation:
12 steps, including "Off"
43dB total attenuation
• 2 channel stereo control
• Can be used with any combination of 4 Ohm to 8 Ohm speakers and
amplifiers.
• Frequency response: 20Hz - 20kHz, +1/-0.5 dB at rated power
DC power-
• Input voltage: +12 VDC
• Power consumption: 80 mA, .96 Watts
Mounting-
• Fits into most 20 cubic in. Junction boxes. 1 5/8"W x 2 7/8"H x 2 5/8"D
(4.1 x 7.3 x 5.4 cm)
Weight-
• 1.1 lbs (.5 kg)
8
LIMITED WARRANTY
The Russound Smart Select™ Volume Control is fully guaranteed for Two
(2) years from the date of purchase against all defects in materials and
workmanship. During this period Russound will replace any defective parts
and correct any defect in workmanship without charge for either parts or
labor. For this warranty to apply, the unit must be installed and used
according to its written instructions. If service is necessary, it must be per-
formed by Russound. The unit must be returned to Russound at the
owner's expense and with prior written permission. Accidental damage
and shipping damage are not considered defects under the terms of the
warranty. Russound assumes no responsibility for defects resulting from
abuse or servicing performed by an agency or person not specifically
authorized in writing by Russound. Damage to or destruction of compo-
nents due to improper use voids the warranty. In these cases the repair
will be made at the owner's expense. To return for repairs, the unit must
be shipped to Russound at the owner's expense, along with a note
explaining the nature of the service required. Be sure to pack in a corru-
gated container with at least 3 inches of resilient material to protect the
unit from damage in transit.
CONNECTION DIAGRAMS FOR RUSSOUND MODEL SSVC. REFER TO THE INSTRUCTIONS ON BACK.
DIAGRAMS ARE NOT TO SCALE.
To other Smart Select
Volume Controls
Figure 1
EZB-1, 4-Way
Connecting
Block
AMP/Receiver
SPEAKERS
SPEAKERS
SPEAKERS
SPEAKERS
Smart Select
™
Volume Control
OUTPUT INPUT
L+
L–
R–
R+
L+
L–
R–
R–
To power
and data
connections
(figure 2)
Speaker Pair
™
Figure 2
EZB-1, 4-Way
Smart Select
™
Connecting
Power Interrupter
Block
SPEAKERS
SPEAKERS
4 conductor, 22AWG
2 twisted pair wire
with sheild
To speakers
and connecting
block (figure 1)
OUTPUT INPUT
12V 1000mA
L+
L–
R–
R+
L+
L–
R–
R–
power supply
pt. No. 846XP
Smart Select
™
Volume Control
To other Smart
Select
Volume
™
Controls
SPEAKERS
SPEAKERS
Advertisement
