Russound ALTX-WIRI 2D Manual

CONNECTION DIAGRAMS FOR RUSSOUND MODEL ALTx-WIRi 2D. REFER TO THE INSTRUCTIONS ON REVERSE SIDE. DIAGRAMS ARE NOT TO SCALE.
1X
2X
8 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
1 X
8 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
8 X 1 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
1 X
8 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
Impedance Matching Charts For UltraMatch™
1 X
Refer to the circuit board illustrations at left, which show the
four possible settings (1X, 2X, 4X, 8X).
Impedance Matching For 4 Ohm Amplifiers
Jumper Settings on Circuit Boards
4X
8X
8 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
Example: The table below shows an 8 ohm minimum impedance
1 X
amplifier with 1 pair of 4 ohm speakers and 3 pairs of 8 ohm
8 X
speakers. The chart indicates the jumper setting should be set at 8X.
4 X
X
1 X - 2
X - 8 X
Impedance Matching For 8 Ohm Amplifiers
2 X - 4
8 X
1 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
1 X
8 X
4 X
X
1 X - 2
X - 8 X
2 X - 4
1 X
View of Status Jumpers
from behind plate
Status
Off Position
OFF ON
Status
On Position
OFF ON
8 Ohm Pairs
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
0 - 1X 1X 2X 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
1 1X 2X 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
2 2X 4X 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
3 4X 4X 4X 8X 8X 8X 8X 8X 8X 8X 8X
4 4X 8X 8X 8X 8X 8X 8X 8X 8X
5 8X 8X 8X 8X 8X 8X 8X
6 8X 8X 8X 8X 8X
7 8X 8X 8X
8 8X
8 Ohm Pairs
0 1 2 3 4 5 6 7 8
0 - 1X 2X 4X 4X 8X 8X 8X 8X
1 2X 4X 4X 8X 8X 8X 8X
2 4X 8X 8X 8X 8X
3 8X 8X 8X
4 8X
Audio Receiver
EZB-1 Connecting Block
Amplifier
Speaker
Output
SPEAKERS SPEAKERS
SPEAKERS SPEAKERS
ALTx-WIRi 2D
INPUT
R+ R- L- L+
L+ L- R- R+
OUTPUT
846C to switched
AC outlet on Receiver
Electrical box
8X
4X
1X -2X
2X -4X
1X -8X
8X
4X
1X -2X
2X -4X
1X -8X
S
TATUS
+12VDC
P
OWER
+12VDC
IR R I
ECEIVER N
IR C I
OMMON N
+
12VDC
GND
STATUS
SIGNAL
DESIGNED IN USA MADE IN KOREA
Speakers
WHITE (STATUS)
BLUE (SIGNAL)
RED (+12VDC)
BLACK (GND)
IR and Status Connections
ALTx-WIRi 2D
Decora®
faceplate
S
STA TU
RO L
CO NT
UR CE
IR SO
846C to AC Outlet
857 Infrared Connecting Block
IR Emitters to
Source Components