Sanyo VDC-DP9584S Installation Manual
  1. Manuals
  2. Brands
  3. Sanyo Manuals
  4. Security Camera
  5. VDC-DP9584S
  6. Installation manual
Sanyo VDC-DP9584S Installation Manual

Sanyo VDC-DP9584S Installation Manual

Color ccd camera
Hide thumbs Also See for VDC-DP9584S:
1
2
3
4
5
6
7
8
Table of Contents

Advertisement

Quick Links

Download this manual See also: Instruction Manual
INSTALLATION MANUAL
Color CCD Camera
THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED
SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL
CODES.
Please read this manual before installing and using this unit, and always follow the instructions
in it for proper use. Please also read the separate INSTRUCTION MANUAL before using the unit
for proper use.
This unit can be installed on the ceiling or wall.
When installing, first remove the built-in camera
from the unit.
Ceiling Installed (see page 1)
(In-ceiling routing)
(Surface routing)
Wall Installed (see page 3)
(In-wall routing)
Since the conduit hole cover is not
waterproof-finished, always be sure to
seal the cover entirely by puttying, for
example, upon completion of installation.
(Surface routing)
VDC-DP9585P
Important
• Be careful when opening holes for installing
the unit. Work with the power and video
cables pulled out for easy installation.
• Make sure to properly perform waterproofing
for the ceiling or wall where you are installing
the unit.
• Make sure that the surface in the installation
location has no unevenness and is strong
enough to bear the total weight of the unit.
• Install this unit in an environment where the
temperature range stays between -10°C
and +50°C (no condensation allowed).
• As a precaution against static electricity
damage, touch a nearby metal object (door
knob, etc.) to dissipate static electricity in
your body before touching this unit.
b When routing the cables on ceiling or wall
surfaces:
Loosen the conduit hole cover fixing screw (A) on
the back of the camera unit base with the hexagonal
wrench (small), open the cover (B), and pass the
connection cables through the conduit hole.
A
B
b Replacement timing of major parts
If the unit is used continuously, parts will
become worn and deteriorated depending on
the environment of use.
It is recommended that parts be replaced
approximately every 2 years (approximately
1,200,000 times) in order to maintain unit
performance.
• Motor, cables used in mechanical parts,
gears, etc.

Advertisement

Table of Contents
loading

Related Manuals for Sanyo VDC-DP9584S

Summary of Contents for Sanyo VDC-DP9584S

  • Page 1 INSTALLATION MANUAL Color CCD Camera VDC-DP9585P THIS INSTALLATION SHOULD BE MADE BY A QUALIFIED SERVICE PERSON AND SHOULD CONFORM TO ALL LOCAL CODES. Please read this manual before installing and using this unit, and always follow the instructions in it for proper use. Please also read the separate INSTRUCTION MANUAL before using the unit for proper use.

  • Page 2: Installing On The Ceiling

    Installing on the Ceiling 1. Remove the camera unit 2. Install the camera unit base Loosen the four screws (A) using the Attach the cushioning sheet (F) to the hexagonal wrench (large) and open the back of the camera unit base (G), open a dome cover.

  • Page 3: Mount The Camera Unit

    3. Mount the camera unit 4. Adjust/Check the video image from the camera Connect the cables from the ceiling. Push the excess of connected cables into Set up the camera remotely (see the the ceiling. back of this manual). For details on the connections, see page 5. Check the settings screen or camera angle on a portable monitor (see the back Free the locks (E) on the base chassis.

  • Page 4: Installing On The Wall

    Installing on the Wall 1. Remove the camera unit 3. Install the camera unit base • Check the top and bottom of the camera unit See “Installing on the Ceiling” (see page 1). base using the pattern sheet. Attach the cushioning sheet (D) to the 2.
  • Page 5 Free the locks (G) on the base chassis. 5. Adjust/Check the video image from the camera Set up the camera remotely (see the back of this manual). Check the settings screen or camera angle on a portable monitor (see the back of this manual).

  • Page 6: Monitor Connection

    Connections Do not connect the power cord until all other Connection for a communication device connections have been completed. for remote operation DC12 AC24 – BLACK WHITE DAY/NIGHT YELLOW ALARM IN1 PURPLE ALARM IN2 ORANGE BLUE ALARM OUT Note: GRAY COMMON BNC type RG-6U, 300 m or less...
  • Page 7 YELLOW RS-485 (A) Controller PURPLE RS-485 (B) GRAY UTP (+) Receiver WHITE UTP (–) Note: All connection cables should be 24 AWG or higher with a maximum length of no more than 600 m. Alarm Signal Input Color or Black-and-White Setting For details, see “Specifying Alarm Input”...

  • Page 8: Adjusting The Camera

    Adjusting the Camera bSetting up the camera remotely Use of the separately ordered Camera Control Unit (VAC-70) is recommended for setting and adjustment of this camera. The Camera Control Unit allows you to adjust the camera angle (pan/tilt) as well as perform advanced settings from the main menu.

This manual is also suitable for:

Vdc-dp9585p

Table of Contents