223Vw User Manual TABLE OF CONTENTS FOR YOUR SAFETY ------------------------------------------------------------- SAFETY PRECAUTIONS ------------------------------------------------- SPECIAL NOTES ON LCD MONITORS ------------------------------ BEFORE YOU OPERATE THE MONITOR --------------------------------- FEATURES ------------------------------------------------------------------- PACKING LIST -------------------------------------------------------------- INSTALLATION INSTRUCTIONS -------------------------------------- ADJUSTING THE VIEWING ANGLE ---------------------------------- OPERATING INSTRUCTIONS -------------------------------------------------...
Page 3
Before operating the monitor please read this manual thoroughly. This manual should be retained for future reference. FCC Class B Radio Frequency Interference Statement WARNING: (FOR FCC CERTIFIED MODELS) NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 4
PRECAUTIONS Do not use the monitor near water, e.g. near a bathtub, washbowl, kitchen sink, laundry tub, swimming pool or in a wet basement. Do not place the monitor on an unstable cart, stand, or table. If the monitor falls, it can injure a person and cause serious damage to the appliance.
SPECIAL NOTES ON LCD MONITORS The following symptoms are normal with LCD monitor and do not indicate a problem. Due to the nature of the fluorescent light, the screen may flicker during initial use. Turn off the Power Switch and then turn it on again to make sure the flicker disappears.
Power Cord D-Sub Cable DVI Cable INSTALLATION INSTRUCTIONS SWIVEL BASE Install Remove Figure 1 Installing and Removing the Swivel Base...
Page 7
POWER CORD Power Source: 1. Make sure that the power cord is the correct type required in your area. 2. This LCD monitor has an External universal power supply that allows operation in either 100/120V AC or 220/240V AC voltage area (No user adjustment is required.) 3.
Figure 2 Connecting Cables Power input socket DVI input socket Signal input socket ADJUSTING THE VIEWING ANGLE For optimal viewing it is recommended to look at the full face of the monitor, then adjust the monitor’s angle to your own preference. Hold the stand so you do not topple the monitor when you change the monitor’s angle.
Page 9
Figure 3 NOTES Do not touch the LCD screen when you change the angle. It may cause damage or break the LCD screen. Careful attention is required not to catch your fingers or hands when you change the angle.
OPERATING INSTRUCTIONS GENERAL INSTRUCTIONS Press the power button to turn the monitor on or off. The other control buttons are located on the side of the monitor (See Figure 4). By changing these settings, the picture can be adjusted to your personal preferences. The power cord should be connected.
Page 11
EXTERNAL CONTROLS 1. Input Select 2. Auto Adjust button / Exit 3. Brightness 4. Contrast 5. MENU 6. Power button 7. LED FRONT PANEL CONTROL Power Button Press this button to switch ON/OFF of monitor’s power. MENU / ENTER : Active OSD menu or function adjust confirm or Exit OSD menu when in Contrast /Brightness OSD status.
Auto Adjust button / Exit: When OSD menu is in active status, this button will act as EXIT-KEY (EXIT OSD menu). When OSD menu is in off status, press this button to activate the Auto Adjustment function. The Auto Adjustment function is used to optimized the HPos, VPos, Clock and Focus. OSD Lock Function: To lock the OSD, press and hold the MENU button while the monitor is off and then press power button to turn the monitor on.
Figure 5 The OSD Message ADJUSTING THE PICTURE The descriptions for function control LEDS Main Main Sub Menu Sub Menu Menu Description Menu Item Item Icon Icon Luminance Contrast Contrast from Digital-register.
Page 14
Brightness Backlight Adjustment. Adjust Picture Phase to reduce Focus Horizontal-Line noise. Image Setup Adjust picture Clock to reduce Clock Vertical-Line noise. Adjust the horizontal position of H. Position the picture. Image Position Adjust the verticalposition of the V. Position picture. Warm Recall Warm Color Temperature.
Page 15
Main Main Menu Sub Menu Sub Menu Menu Description Item Item Icon Icon Select input signal from Analog analog source (D-Sub). Input Select Select input signal from digital Digital source (DVI). Adjust the horizontal position H. Position of the OSD. Adjust the verticalposition of OSD Setup V.
Clear each old status of Auto- configuration. Reset Do not execute reset, return to main menu. Exit Exit OSD PLUG AND PLAY Plug & Play DDC2B Feature This monitor is equipped with VESA DDC2B capabilities according to the VESA DDC STANDARD. It allows the monitor to inform the host system of its identity and, depending on the level of DDC used, communicate additional information about its display capabilities.
OFF mode. This reduces the monitor's internal power supply consumption. After the video input signal is restored, full power is restored and the display is automatically redrawn. The appearance is similar to a "Screen Saver" feature except the display is completely off. The display is restored by pressing a key on the keyboard, or clicking the mouse.
Page 18
The power LED is ON , but *Computer Power Switch should be in there’s no video or no picture. the ON position. *Computer Video Card should be snugly seated in its slot *Make sure monitor’s video cable is properly connected to the computer. *Inspect monitor’s video cable and make sure none of the pins are bent.
ERROR MESSAGE & POSSIBLE SOLUTION NO SIGNAL Check that the signal-cable is properly connected , If the connector is loose, tighten the connector’s screws. Check the signal-cable’s connection pins for damage. INPUT NOT SUPPORT Your computer has been set to unsuitable display mode ,set the computer to display mode given in the following table.
Page 20
Input Separate Sync. H/V TTL H-Frequency 30kHz – 80kHz V-Frequency 55-75Hz Display Colors 16.7M Colors Dot Clock 165MHz Max. Resolution 1680 x 1050@60Hz Plug & Play VESA DDC2B Power Consumption ON Mode ≤45W(max) OFF Mode ≤1W Input Connector D-Sub 15pin DVI 24pin Input Video Signal Analog:0.7Vp-p(standard),...
Page 21
Auto Adjust Button Switch Brightness Contrast Power Button MENU External Controls: Functions Contrast Brightness Focus Clock Input Select H. Position V. Position OSD Setup Language (Warm)Color (Cool)Color sRGB RGB Color temperature Information Reset Exit C-Tick, cULus,TUV-GS, TCO’99 Regulatory Compliance...
CONNECTOR PIN ASSIGNMENT 15 - Pin Color Display Signal Cable PIN NO. DESCRIPTION PIN NO. DESCRIPTION Green Detect Cable Blue Ground Ground DDC-Serial Data Ground H-Sync R-Ground V-Sync G-Ground DDC-Serial Clock B-Ground 24 - Pin Color Display Signal Cable...
Page 24
PIN NO. DESCRIPTION PIN NO. DESCRIPTION TMDS Data 2- TMDS Data 3+ TMDS Data 2+ +5V Power TMDS Data Ground(for+5V) Shield TMDS Data 4- Hot Plug Detect TMDS Data 4+ TMDS Data 0- DDC Clock TMDS Data 0+ DDC Data TMDS Data 0/5 Shield N.C.