Related Manuals for Encore ENLTV - V2.2
Summary of Contents for Encore ENLTV - V2.2
- Page 1 Personal Video Recorder ENLTV / ENLTV-FM (PCI TV Capture Card) ENLTV Series User’s Guide Version 2.2...
- Page 2 TIME WITHOUT NOTICE, AND SHOULD NOT BE CONSTRUED AS A COMMITMENT BY US. WE ASSUME NO RESPONSIBILITY OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL, INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT. Copyright Encore Electronics © 2009. All Rights Reserved.
-
Page 3: Table Of Contents
ENLTV User’s Guide - Contents: Chapter 1: Introduction ........................4 1.1 - Package Contents....................... 4 1.2 - System Requirements ......................4 Chapter 2: Getting Started ......................... 5 2.1 - ENLTV / ENLTV-FM Hardware Installation ..............5 2.2 - Device Driver Installation ....................6 2.3 - Install the DirectX®... -
Page 4: Chapter 1: Introduction
ENLTV User’s Guide - Chapter 1: Introduction 1.1 - Package Contents The following items are included in the E NLTV / ENLTV-FM package. CD Setup Disc (includes Software Driver and Utility Software) ENLTV or ENLTV-FM PCI Card Video Cable Audio Cable Remote Controller FM Antenna (ENLTV-FM only) -
Page 5: Chapter 2: Getting Started
ENLTV User’s Guide - Chapter 2: Getting Started 2.1 - ENLTV / ENLTV-FM Hardware Installation Install the ENLTV / ENLTV-FM PCI Card to the computer’s available PCI slot according to your computers manual and new hardware installation procedures. Make sure that the computer’s power cord is unplugged before inserting the ENLTV / ENLTV-FM card to the PCI slot. -
Page 6: Device Driver Installation
ENLTV User’s Guide - 2.2 - Device Driver Installation 1. Placed the CD software that comes with the ENLTV / ENLTV-FM in the CD-ROM drive. (Assuming that the ENLTV / ENLTV-FM PCI TV Tuner card is properly installed to the computer’s PCI slot), then follow the on-screen installation guide below. - Page 7 ENLTV User’s Guide - 3. Click “Next” on driver setup welcome window to continue. 4. Make sure the “Complete” radio button is selected then click “Next” 5. Click “Install” to begin install driver.
- Page 8 ENLTV User’s Guide - 6. Click “Next” button. 7. Click “Continue Anyway” to continue the installation. 8. Click ”Continue Anyway” button...
- Page 9 ENLTV User’s Guide - 9. Click “Finish” button 10. Click “Finish” to reboot PC. 11. To make sure the driver is properly installed and started, open the “Device Manager”. Please double-click the “Sound, video and game controller”.
- Page 10 ENLTV User’s Guide - Device driver installation for Windows Vista™ 1. After ENLTV / ENLTV-FM hardware has been installed, the next time when the computer is powered-on, a message “Found New Hardware” dialogue box will appear on the screen. Click “Cancel” button to close “Found New Hardware”...
- Page 11 ENLTV User’s Guide - 5. Click “Next” on driver setup welcome window to continue. 6. Make sure the “Complete” radio button is selected then click “Next” 7. Click “Install” button...
- Page 12 ENLTV User’s Guide - 8. Click “Next” button 9. Click “Finish” button 10. Click “Finish” button.
- Page 13 ENLTV User’s Guide - 11. To make sure the driver is properly installed and started, open the “Device Manager”. Please double-click the “Sound, video and game controller”.
-
Page 14: Install The Directx
ENLTV User’s Guide - 2.3 - Install the DirectX® Microsoft DirectX® allows 3D hardware acceleration support in Windows® 98, 2000, Windows® XP/64 bit and Windows Vista™ 32bit/64bit. For software MPEG support in Windows 98, you must first install Microsoft DirectX®, and then an MPEG compliant video player. -
Page 15: Install The Enltv Utility Software
ENLTV User’s Guide - 5. Click “Next” to confirm the installation of DirectX 6. Click “Finish” NOTE: The computer will automatically restart. Please save any unsaved files and close all programs before hitting the “Finish” button. 2.4 - Install the ENLTV Utility software. 1. - Page 16 ENLTV User’s Guide - Please read the License Agreement and click “Yes” button Make sure the “Typical” radio button is selected then click “Next” Click “Next” button to accept the default location or choose a different folder Note: We recommend not to change the default location Click “Next”...
- Page 17 ENLTV User’s Guide - Click “Finish” button. NOTE: We recommend restarting your computer right after the Installation Wizard. 2. Install TV application on Windows Vista™ 32/64bit 1. Insert the installation CD into the CD-ROM drive. The setup screen will automatically appear. 2.
- Page 18 ENLTV User’s Guide - 5. Please read the License Agreement and click “Yes” button 6. Make sure the “Typical” radio button is selected then click “Next” 7. Click “Next” button to accept the default location or choose a different folder Note: We recommend not to change the default location...
- Page 19 ENLTV User’s Guide - 8. Click “Next” 9. Click “Finish” to restart your computer. NOTE: We recommend restarting your computer right after the Installation Wizard.
-
Page 20: Chapter 3: Launch The Enltv Program
ENLTV User’s Guide - Chapter 3: Launch the ENLTV Program 3.1 - Running the ENLTV for the first time Click “Start”, move your mouse to “Programs\ENLTV\ENLTV” then click ENLTV NOTE: When the ENLTV Program is first started, it will prompt you to configure the Device Setting. - Page 21 ENLTV User’s Guide - Select the video signal format in your area (NTSC or PAL) from the “TV Tuner Standard” drop-down menu. Select “Line-In” to drop-down menu of the “Audio Input Source” and the “Volume Control Source”. Click “Next” NOTE: •...
-
Page 22: Watch Tv Programs Or Movies From Dvd/Vcr/Camcorder
ENLTV User’s Guide - 3.2 - Watch TV programs or movies from DVD/VCR/Camcorder 5.Double click to full screen 4.Channel Control 3.Volume Control 2.Search TV Channel 7.TV wall 1.Source Switch 6.Channel List 1. Source Switch: click it to select TV, Audio/Video or S-Video. 2. -
Page 23: Record Video
ENLTV User’s Guide - When you do a full screen display, you can use the panel bar to set up your TV box. 1. Fix Panel: To fix the display panel. Show / Hide as mouse drags. 2. Hide Panel: To hide the sub-panel. 3. -
Page 24: Snapshot Image
ENLTV User’s Guide - 3.4 - Snapshot Image 1. Click the “Setting” button to setup the image format. 2. The ENLTV supports BMP and JPEG image format. The default is JPEG. Please choose your desired format. 3. Click “Snapshot” button to capture image. 3.5 - Playback Video 1. - Page 25 ENLTV User’s Guide - Exit: To exit the video playback window, [Esc] or [ALT]+[F4] on keyboard equalized Minimize: To minimize the video playback window, click "MoviePlayer" in desktop taskbar to restore display Hide Control Panel: To hide video control panel, right click video window and select "Control Panel"...
-
Page 26: Browse Images
ENLTV User’s Guide - 3.6 - Browse Images 1. Click the “Browse Image” to retrieve the saved pictures. 2. You can use the “Browse Image” software to control picture zoom in/out, or rename. The menu bar contains many function buttons for easy operations, these are: Refresh: To refresh the display snapshot image in current folder. -
Page 27: Time-Shifting
ENLTV User’s Guide - 3.7 – Time-Shifting Right click inside the ENLTV video window and select the “Timeshift” function. Video is now being recorded to your hard disk while showing live on screen. TimeShift You can click “pause” button or slide the “timer”... - Page 28 ENLTV User’s Guide - Click “Stop” button on the control panel, or right click inside the ENLTV video window and select “Stop” from the context menu to stop the time-shift function.
-
Page 29: Using And Setting Up The Fm Radio
ENLTV User’s Guide - 3.8 - Using and setting up the FM Radio (This feature is for ENLTV-FM only) NOTE: ENLTV-FM is equipped with FM Radio receiver only. There is no AM Radio receiver included. Click the “Switch Video Source” button then select “Radio Mode”. -
Page 30: Chapter 4: Using The Remote Control
ENLTV User’s Guide - Chapter 4: Using the Remote Control The Remote control allows you to operate the ENLTV program, such as turning the TV on or off, changing channel and volume, etc. Aim the upper front side of the Remote Control to the Remote Control Receiver as you would do on other infrared remote control. -
Page 31: Chapter 5: Frequently Asked Questions
The ENLTV/ENLTV-FM driver and software should match. If step 1 did not fix the problem, uninstall the driver and the software, and then reinstalling them from the product CD again. If your product CD is not available with you, you can check our web site at http://www.encore-usa.com for download. - Page 32 ENLTV User’s Guide - Q: How do I uninstall the ENLTV software? A: For Windows® XP, there are two ways to uninstall the ENLTV Utility software. 1. Go to Start > All Program > ENLTV > Uninstall ENLTV program. 2. Go to Windows “Control Panel” > “Add or Remove programs”. Select ENLTV then click “Remove”...
- Page 33 ENLTV User’s Guide - If the audio is still not working, check the sound card settings. See the User’s Guide, page 21, “Device Initial Setting” to set the “Audio Input Source”. Make sure all the appropriate audio levels are set about 3/4 high. Q：...
-
Page 34: Chapter 6: Technical Support
ENLTV User’s Guide - Chapter 6: Technical Support For Technical Support or Installation Hotline contacts please visit our web site at http://www.encore-usa.com 2009/05/01 Version: 2.2...