Table of Contents
Advertisement
Quick Links
How to install and operate the DLS CA10,
mono amplifier.
Welcome!
This owners manual is written in easy english and
uses a lot of drawings to simply the installation and
use of the above amplifiers.
Your DLS amplifiers must be installed correctly in
order to work well. This manual will show you how
to install the amplifier like a pro. Please read the
entire manual before beginning the installation.
Install the amplifier yourself if you feel confident with
our instructions and if you have the proper tools.
However if you feel unsure, turn over the installa-
tion job to someone better suited to it.
Warranty Service
This amplifier is covered by warranty, depending
on the conditions in the country where it is sold. If
the amplifier is returned for service, please include
the original dated receipt with the product.
Technical Assistance
For technical assistance ask the shop where the
product was sold or the distributor in your very coun-
try.
You can always phone the DLS Helpdesk in Sweden
+ 46 31 84 00 60 or send an e-mail to info@dls.se.
Information can also be found on our WEB-site
www.dls.se
Contents
Specifications................................
Features...................................
Installation................................
Trouble-shooting.......................... 2
Tools and materials needed..........
Amplifier installation kit................
Routing Wires............................
Power and Outputs.....................
Inputs and controls.....................
Bass Boost,Crossovers................
Phase control.............................
Subwoofers...............................
Testing...........................................
Professional tips..........................
Specifications
DLS CLASSIC
Number of channels
Power output in 4 ohm (0,2% THD)
Max output in 2 ohm (0,2% THD)
Max output in 1 ohm (0,3% THD)
All above output power ratings at 13,8 Volt
Signal to noise ratio, A-weighted
Damping factor
Frequency response
Input impedance
Input sensitivity
Phase control
Bass boost adjustable gain
Filter subsonic, 18 dB slope
Filter lowpass 12 db slope
* can be switched in/out
Power consumption, idle
Fuse
Dimensions (mm)
Dimensions (inch)
Weight
We follow a policy of continuous advancement in
development.
For this reason all or part of specifications & designs
may be changed without prior notice.
1
2
2
3
3
3
4
5
5
5
5
6
6
7
CA 10
1
1 x 400 W
1 x 700 W
1 x 1000 W
>100 dB
>100
10 Hz - 125 Hz
>10 kohm
0,25 - 5V
0-180 degrees
continuous
0 - 18 dB
25 Hz fixed*
40-125 Hz
1,0 A
5 x 30A
51,5x450x290
2,03x17,7x11,4
6,5 kg
Advertisement
Table of Contents
Related Manuals for DLS CA10ENG
Summary of Contents for DLS CA10ENG
-
Page 1: Table Of Contents
You can always phone the DLS Helpdesk in Sweden + 46 31 84 00 60 or send an e-mail to info@dls.se. Information can also be found on our WEB-site www.dls.se We follow a policy of continuous advancement in development. -
Page 2: Features
4. Check the amplifier protection fuses. Are these broken change to new ones with the same value. If short circuiting continues, contact your local DLS dealer. A fault may exist in the amplifier. Before you begin installation 5. To start the amplifier requires a remote voltage of 9-15 volt. -
Page 3: Tools And Materials Needed
CA10 Routing wires Tools and material needed Tools: Š Š Š Š Š Flat and Phillips screwdrivers Š Š Š Š Š Wire cutter Š Š Š Š Š Wire stripper Š Š Š Š Š Electric drill with drills Š... -
Page 4: Wiring
+12V REM GND DLS FH 2B fuse holder Connect the battery cable by a crimp fork terminal ( spade ) to the +12 Volt on the amplifier. -
Page 5: Inputs And Controls
CA10 Input and controls Input Wiring Bass Boost on CA10 Inputs may be low level from the RCA output of the car stereo.If your head unit has a separate RCA sub Bass Boost is used to Bass Boost output we recommend that you to use it for connection increase bass 6dB 12dB... -
Page 6: Speaker Wiring
CA10 Speaker wiring CA 10 One 4 ohm subwoofer Two 2 ohm subwoofers 4 ohm load 2 ohm load Speaker Speaker Filter settings Testing Subsonic Before you finish the installation, you should do the following tests to make sure the wiring is correct and 40Hz 125Hz everything is operating properly. -
Page 7: Professional Tips
1,5 Volt route original cable away from source of interference. If noise remains regardless of cable position, try to use so called Quasi-balanced signal cables. DLS PRO or ULTIMATE cables are quasibalanced. Professional Tip: Professional Tip: Installing in trunk Securing wires When installing the amplifier in the trunk, run the Use wire ties to bundle together when possible. - Page 8 DLS Svenska AB P.O. Box 13029 Artillerigatan 25 S-40251 Göteborg, Sweden Tel: +46 31 840060 Fax: +46 31 844021 E-mail: info@dls.se www.dls.se...